QUICKSTART “BASIC” GUIDELINES FOR MODEL 6002 - FOR A GATE UP TO 14 FEET, 500LBS AND “OPENING TO THE INSIDE”
Installation
Weld front and rear brackets
in positions shown.
Tip: Cover the actuator arm
to protect it from welding
sparks before doing any
welding.
The 6002 is intended for installation only on swing gates used for vehicles.
Pedestrians must be supplied with a separate access opening. For safety and installation instructions, please refer to
6002 Actuator Arm and Control Box Mounting manual, 115 VAC or Solar Control Box Wiring/Owner’s manuals.
Arm in “Open to the Inside” Position
Arm in Closed Position
46
3
/4” Closed Position
7”
7”
90°
Gate Hinge Pivot Point
Front Bracket Pivot Point
Rear Bracket
Front Bracket
Rear Bracket Pivot Point
(Actuator Cover On)
(Actuator Cover Off)
2
7
/8”
Actuator
Cable
Power Conduit
Loops Conduit
Securely mount a control
box near the actuator arm
with appropriate hardware
(not included).
Control Box
Coaxial
Cable
Antenna
Actuator arm and brackets MUST be level!
A support bar must be
installed the entire
length of the gate to
support the pickets.
Remove
3 Screws
ONLY
Remove
Actuator Cover
Coaxial Cable Antenna Kit
P/N 1514-073 (Sold separately)
Bottom
Middle
Top
Clevis Pins
Rear
Front
Front clevis pin MUST fit into
countersunk hole to allow
retaining ring to be installed.
Retaining Ring
120 S. Glasgow Avenue
Inglewood, California 90301
U.S.A.
THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY.
Visit
www.dkslocator.com
to find a professional installing and servicing dealer in your area.
115 VAC
or Solar
Power
Input
Brown wire
Blue wire
Orange wire
Red wire
Yellow wire
Green wire
Green/Yellow wire
NOT USED
7-Wire Operator
Actuator Cable
Photo Sensors Height
Close Beam
Open Beam
Open Beam
Close Beam
Reversing Edge
Photo Sensor
Photo Sensor
Sensor mounted
just below actuator
arm cable.
Gate Opened
Gate Closed
Note: Refer to YOUR chosen 115 VAC OR
Solar powered control box manuals to
wire entrapment protection devices.
Outside
Property
Inside
Property
Single operator connects to
PRIMARY connection ONLY
on the 115 VAC OR Solar
control box circuit board.
1
7
8
6
5
4
3
2
PRIMARY
Circuit board power MUST be ON to adjust limit sensors, LEDs will light.
Limit
Limit Sensors Adjustment
t
180°
limit nut
OPEN
OPEN
Slow Down
n
n
Manual Release
Manually move the gate to
the desired open or closed
position. Loosen the limit nuts and
slowly slide the limit assemblies until the
LIMIT LEDs on the circuit board light up.
5 Limit
3 Limit
4 Slo Dwn
6 Slo Dwn
4302
4302
DO NOT cycle operator before limit sensors and DIP-switches
have been adjusted, damage could occur to gate and operator.
Powered shaft rotated back 2 turns.
Fully Extended (Bottomed Out)
OPEN
OPEN
Manually release
with allen wrench.
Powered Shaft
Manually release the arm and fully extend the powered shaft. Rotate it back two full turns before installing the arm.
Prevent Powered Shaft from Bottoming Out
6002-066-K-10-16
Manual Release
OPEN
OPEN
180°
Allen
wrench
is inside
of cover.
Cover holes with aluminum
tape on top ONLY.
Opening Direction DIP-Switch 1 (SW 1)
Refer to YOUR chosen 115 VAC OR Solar powered control box manuals for
complete DIP-switch settings.
ON setting.
Opens clockwise.
ON setting.
Opens counter-clockwise.
SW 1
1
ON
2 3 4 5 6 7 8
5” or less
Gate Closed
21”
Typical
27.5”
Max
Reversing Edge
is mounted
along ENTIRE
end of gate.
4302
Wiring to Circuit Board
All potential entrapment
areas MUST be protected
with an external entrapment
protection device.
At least ONE external
entrapment protection device
MUST be installed or the
operator will NOT function.
External
Entrapment
Protection
Devices
Potential
Entrapment
Area
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
DKS 6002 User manual
-
DKS 6002 Pre-2016 User manual
-
-
DKS 6003 Aug 2018 - later User manual
-
-
-
-
-
-
