PAR64

HQ Power PAR64 User manual

  • Hello! I am an AI chatbot trained to assist you with the HQ Power PAR64 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
VDPLP64xx (xx = B2, C2, B3, C3)
20.04.2010 ©Velleman nv
2
terminator
eindweerstand
résistance de terminaison
terminación
Terminierung
How to turn the controller line from 3-pins into 5-pins (plug and socket)
Controller line van 3-pin naar 5-pin aanpassen (stekker en contact).
Modifier la ligne du contrôleur de 3 broches en 5 broches (fiche et contact)
Modificar la línea del controlador de 3 polos y 5 polos (conector y contacto)
Die Controller-Linie von 3-Pin nach 5-Pin anpassen (Stecker und Buchse).
VDPLP64xx (xx = B2, C2, B3, C3)
20.04.2010 ©Velleman nv
3
User manual
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its
lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted
municipal waste; it should be taken to a specialized company for recycling. This device
should be returned to your distributor or to a local recycling service. Respect the local
environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing HQ-power! Please read the manual thoroughly before bringing this device
into service. If the device was damaged in transit, do not install or use it and contact your dealer.
2. Safety Instructions
Be very careful during the installation: touching live wires can cause life-
threatening electroshocks.
Always disconnect mains power when device not in use or when servicing or
maintenance activities are performed. Handle the power cord by the plug only.
Keep this device away from children and unauthorized users.
Caution: device heats up during use.
There are no user-serviceable parts inside the device. Refer to an authorized
dealer for service and/or spare parts.
This device falls under protection class I. It is therefore essential that the device be earthed. Have
a qualified person carry out the electric connection.
Make sure that the available voltage does not exceed the voltage stated in the specifications of
this manual.
Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it
if necessary.
Respect a minimum distance of 0.5m between the device’s light output and any illuminated
surface.
Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).
Do not stare directly at the light source, as this may cause epileptic seizure in sensitive people.
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
Indoor use only. Keep this device away form rain, moisture, splashing and
dripping liquids.
Keep this device away from dust and extreme heat. Make sure the ventilation
openings are clear at all times. For sufficient air circulation, leave at least 1” (±2.5
cm) in front of the openings.
Protect this device from shocks and abuse. Avoid brute force when operating the
device.
Familiarise yourself with the functions of the device before actually using it. Do not allow
operation by unqualified people. Any damage that may occur will most probably be due to
unprofessional use of the device.
All modifications of the device are forbidden for safety reasons. Damage caused by user
modifications to the device is not covered by the warranty.
VDPLP64xx (xx = B2, C2, B3, C3)
20.04.2010 ©Velleman nv
4
Only use the device for its intended purpose. All other uses may lead to short circuits, burns,
electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the
warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty
and the dealer will not accept responsibility for any ensuing defects or problems.
A qualified technician should install and service this device.
Do not switch the device on immediately after it has been exposed to changes in temperature.
Protect the device against damage by leaving it switched off until it has reached room
temperature.
This device is designed for professional use on stage, in discos, theatres, etc. The VDPLP64xx
can be used indoor (<35°C, <75%RH) with an alternating current of max. 240V AC/50Hz.
Lighting effects are not designed for permanent operation: regular operation breaks will prolong
their lives.
Use the original packaging if the device is to be transported.
Keep this manual for future reference.
4. Features
fanless cooling
short double bracket
stand-alone, master/slave or music trigger mode
DMX-controlled via 5 channels for smooth RGB colour mixing
dimmer and shutter function via DMX mode
special angled connection panel
lens protection screen
blue LED display for easy menu setup (auto-off function)
5. Overview
Refer to the illustrations on page 2 of this manual.
1 MODE selection button 5
DMX input
2 UP-Button 6
DMX output
3 DOWN-Button 7
AC output
4 LCD 8
AC input
6.
Installation
a) Floor standing
Loosen the knobs on the side of the mounting bracket and unfold the bracket.
Place the device in such a way that passers-by can not touch it nor stumble over it or its power
cord(s).
b) Overhead mounting
Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable
norms.
The construction to which the device is attached should be able to support 10 times the weight of
the device for one hour without deformation.
The installation must always be secured with a secondary attachment e.g. a safety cable.
Never stand directly below the device when it is being mounted, removed or serviced. Have a
qualified technician check the device once a year and once before you bring it into service.
Install the device in a location with few passers-by and inaccessible to unauthorised persons.
Overhead mounting requires extensive experience: calculating workload limits, determining the
installation material to be used… Have the material and the device itself checked regularly. Do not
attempt to install the device yourself if you lack these qualifications as improper installation may
result in serious injuries.
For truss-mounting, use an appropriate clamp (not incl.) and fit an M10 bolt through the centre of
the (folded) bracket.
Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
Make sure there is no flammable material within a 50cm radius of the device.
VDPLP64xx (xx = B2, C2, B3, C3)
20.04.2010 ©Velleman nv
5
c) DMX-512 connection
Refer to the illustrations on page 2 of this manual.
When applicable, connect an XLR cable to the female 3-pin XLR output of a controller (not incl.)
and the other side to the male 3-pin XLR input [5] of the VDPLP64xx. Multiple VDPLP64xx’s
can be linked through serial linking. The linking cable should be a dual core, screened cable with
XLR input and output connectors.
A DMX terminator is recommended for installations where the DMX cable has to run a long
distance or is in an electrically noisy environment (e.g. discos). The terminator prevents
corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR
plug with a 120Ω resistor between pins 2 and 3, which is then plugged into the XLR output socket
[6] of the last device in the chain.
d) general
Make sure there is no flammable material within a 50cm radius of the device and there is
sufficient cooling.
Have a qualified electrician carry out the electrical connection.
Connect the device to the mains with the power plug [8]. Don’t connect it to a dimming pack.
The output connector [7] can be used to supply power to other devices (max. 8A).
The installation has to be approved by an expert before the device is taken into service.
7. Operation
Refer to the illustrations on page 2 of this manual.
The VDPLP64xx can work stand-alone with fixed colour output or controlled by an external DMX-
controller (not incl.).
The VDPLP64xx in master mode generates DMX values on the DMX output [6]. Linked devices
will follow the behaviour of the master when they are placed in slave mode.
a) Colour mode “C” (master)
Press the MODE selection button [1] until the first digit of display [4] shows “C”.
Use the UP- [2] or DOWN-button [3] to select all-off or one of the twelve preset colours (see
table below).
C 0 all off C 7 Lime
C 1 Red C 8 Orange
C 2 Green C 9 Marine
C 3 Blue C10 Frog
C 4 Yellow C11 Lavender
C 5 Pink C12 Candy
C 6 Turquoise C13 White
The selected setting is automatically stored in memory.
b) Slave mode “SLA”
Press the MODE selection button [1] until the display [4] showsSLA”. This sets the units DMX-
channel to 001.
While a DMX-signal is received, a LED on the lower right will be on.
Slave mode can also be used fro remotely controlling the unit if no specific DMX address is
required and channels 001~003 can be used as default.
c) DMX mode “d”
Press the MODE selection button [1] until the display [4] showsd”. After a few seconds, the
display will show the DMX starting address.
All DMX-controlled devices need a digital start address so that the correct device responds to the
signals. This digital start address is the channel number from which the device starts to “listen” to
the DMX controller. The same starting address can be used for a whole group of devices or an
individual address can be set for every device.
When all devices have the same address, all the units will “listen” to the control signal on one
particular channel. In other words: changing the settings of one channel will affect all devices
simultaneously. If you set individual addresses, each device will “listen” to a separate channel
number. Changing the settings of one channel will only affect the device in question.
VDPLP64xx (xx = B2, C2, B3, C3)
20.04.2010 ©Velleman nv
6
In case of the 5-channel VDPLP64xx, you will have to set the start address of the first unit to
001 (CH1~4), the second unit to 006 (1 + 5) (CH5~8), the third to 011 (6 + 5) (CH9~12), and
so on.
Use the UP- [2] or DOWN-button [3] to select a DMX starting address. After selecting, it takes
±3s before the address becomes active. The display shows alternately the address and “d”.
The selected address is automatically stored in memory.
While a DMX-signal is received, a LED on the lower right will be on.
The unit receives DMX values in a packet of 5 channels and mirrors this data on the DMX output
[6]:
DMX channel Value Range Function
CH1 000-255 red (Out1 level)
CH2 000-255 green (Out2 level)
CH3 000-255 blue (Out3 level)
CH4 0-100 Dimmer
CH5 0-100 Shutter
d) Display ON/OFF
When the display does not detect user inputs for ±25s, it will automatically switch off.
To switch it on again, press any button (settings are not affected).
e) Key lock
Pressing and holding the MODE-button [1] for more than 3s will lock all buttons ([1], [2] and
[3]). The display shows alternately the current mode and “LOC”.
Press and hold the MODE-button [1] again for more than 3s to unlock the buttons.
f) Switch-on status
The device always returns to the mode/status it was in when it was switched off. However, all
DMX values are cleared at power-off.
g) DMX signal loss
The device will retain the status it was in before signal loss.
8.
Cleaning and maintenance
1. All screws should be tight and free of corrosion.
2. The housing, the lenses, the mounting supports and the installation location (e.g. ceiling,
suspension, trussing) should not be deformed, modified or tampered with e.g. do not drill extra
holes in mounting supports, do not change the location of the connections …
3. Mechanically moving parts must not show any signs of wear and tear.
4. The electric power supply cables must not show any damage. Have a qualified technician
maintain the device.
5. Disconnect the device from the mains prior to maintenance activities.
6. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
7. There are no user-serviceable parts.
8. Contact your dealer for spare parts if necessary.
9. Technical specifications
VDPLP64B2 VDPLP64C2 VDPLP64B3 VDPLP64C3
colour black chrome black chrome
power supply 90-250VAC / 50-60Hz (switching power mode)
power consumption
20W 44W
DMX channels 5
number of LEDs 177 (36 R, 83 G, 58 B) 39 x 1W (9 R, 18 G, 12 B) - Edison
beam angle 20°
dimensions Ø186 x 252mm
weight 1.5kg 2kg
Velleman® Service and Quality Warranty
Velleman® has over 35 years of experience in the electronics world
and distributes its products in more than 85 countries.
All our products fulfil strict quality requirements and legal stipulations
in the EU. In order to ensure the quality, our products regularly go
through an extra quality check, both by an internal quality
department and by specialized external organisations. If, all
precautionary measures notwithstanding, problems should occur,
please make appeal to our warranty (see guarantee conditions).
General Warranty Conditions Concerning Consumer Products
(for EU):
• All consumer products are subject to a 24-month warranty on
production flaws and defective material as from the original date of
purchase.
• Velleman® can decide to replace an article with an equivalent
article, or to refund the retail value totally or partially when the
complaint is valid and a free repair or replacement of the article is
impossible, or if the expenses are out of proportion.
You will be delivered a replacing article or a refund at the value of
100% of the purchase price in case of a flaw occurred in the first year
after the date of purchase and delivery, or a replacing article at 50%
of the purchase price or a refund at the value of 50% of the retail
value in case of a flaw occurred in the second year after the date of
purchase and delivery.
• Not covered by warranty:
- all direct or indirect damage caused after delivery to the article (e.g.
by oxidation, shocks, falls, dust, dirt, humidity...), and by the article,
as well as its contents (e.g. data loss), compensation for loss of
profits;
- frequently replaced consumable goods, parts or accessories such as
batteries, lamps, rubber parts, drive belts... (unlimited list);
- flaws resulting from fire, water damage, lightning, accident, natural
disaster, etc. …;
- flaws caused deliberately, negligently or resulting from improper
handling, negligent maintenance, abusive use or use contrary to the
manufacturer’s instructions;
- damage caused by a commercial, professional or collective use of
the article (the warranty validity will be reduced to six (6) months
when the article is used professionally);
- damage resulting from an inappropriate packing and shipping of the
article;
- all damage caused by modification, repair or alteration performed by
a third party without written permission by Velleman®.
• Articles to be repaired must be delivered to your Velleman® dealer,
solidly packed (preferably in the original packaging), and be
completed with the original receipt of purchase and a clear flaw
description.
• Hint: In order to save on cost and time, please reread the manual
and check if the flaw is caused by obvious causes prior to presenting
the article for repair. Note that returning a non-defective article can
also involve handling costs.
• Repairs occurring after warranty expiration are subject to shipping
costs.
• The above conditions are without prejudice to all commercial
warranties.
The above enumeration is subject to modification according to
the article (see article’s manual).
Velleman® service- en kwaliteitsgarantie
Velleman® heeft ruim 35 jaar ervaring in de elektronicawereld en
verdeelt in meer dan 85 landen.
Al onze producten beantwoorden aan strikte kwaliteitseisen en aan de
wettelijke bepalingen geldig in de EU. Om de kwaliteit te waarborgen,
ondergaan onze producten op regelmatige tijdstippen een extra
kwaliteitscontrole, zowel door onze eigen kwaliteitsafdeling als door
externe gespecialiseerde organisaties. Mocht er ondanks deze
voorzorgen toch een probleem optreden, dan kunt u steeds een
beroep doen op onze waarborg (zie waarborgvoorwaarden).
Algemene waarborgvoorwaarden consumentengoederen (voor
Europese Unie):
• Op alle consumentengoederen geldt een garantieperiode van 24
maanden op productie- en materiaalfouten en dit vanaf de
oorspronkelijke aankoopdatum.
• Indien de klacht gegrond is en een gratis reparatie of vervanging
van een artikel onmogelijk is of indien de kosten hiervoor buiten
verhouding zijn, kan Velleman® beslissen het desbetreffende artikel
te vervangen door een gelijkwaardig artikel of de aankoopsom van
het artikel gedeeltelijk of volledig terug te betalen. In dat geval krijgt
u een vervangend product of terugbetaling ter waarde van 100% van
de aankoopsom bij ontdekking van een gebrek tot één jaar na
aankoop en levering, of een vervangend product tegen 50% van de
kostprijs of terugbetaling van 50 % bij ontdekking na één jaar tot 2
jaar.
• Valt niet onder waarborg:
- alle rechtstreekse of onrechtstreekse schade na de levering
veroorzaakt aan het toestel (bv. door oxidatie, schokken, val, stof,
vuil, vocht...), en door het toestel, alsook zijn inhoud (bv. verlies van
data), vergoeding voor eventuele winstderving.
- verbruiksgoederen, onderdelen of hulpstukken die regelmatig dienen
te worden vervangen, zoals bv. batterijen, lampen, rubberen
onderdelen, aandrijfriemen... (onbeperkte lijst).
- defecten ten gevolge van brand, waterschade, bliksem, ongevallen,
natuurrampen, enz.
- defecten veroorzaakt door opzet, nalatigheid of door een
onoordeelkundige behandeling, slecht onderhoud of abnormaal
gebruik of gebruik van het toestel strijdig met de voorschriften van de
fabrikant.
- schade ten gevolge van een commercieel, professioneel of collectief
gebruik van het apparaat (bij professioneel gebruik wordt de
garantieperiode herleid tot 6 maand).
- schade veroorzaakt door onvoldoende bescherming bij transport van
het apparaat.
- alle schade door wijzigingen, reparaties of modificaties uitgevoerd
door derden zonder toestemming van Velleman®.
• Toestellen dienen ter reparatie aangeboden te worden bij uw
Velleman®-verdeler. Het toestel dient vergezeld te zijn van het
oorspronkelijke aankoopbewijs. Zorg voor een degelijke verpakking
(bij voorkeur de originele verpakking) en voeg een duidelijke
foutomschrijving bij.
• Tip: alvorens het toestel voor reparatie aan te bieden, kijk nog eens
na of er geen voor de hand liggende reden is waarom het toestel niet
naar behoren werkt (zie handleiding). Op deze wijze kunt u kosten en
tijd besparen. Denk eraan dat er ook voor niet-defecte toestellen een
kost voor controle aangerekend kan worden.
• Bij reparaties buiten de waarborgperiode zullen transportkosten
aangerekend worden.
• Elke commerciële garantie laat deze rechten onverminderd.
Bovenstaande opsomming kan eventueel aangepast worden
naargelang de aard van het product (zie handleiding van het
betreffende product).
Garantie de service et de qualité Velleman®
Velleman® jouit d’une expérience de plus de 35 ans dans le
monde de l’électronique avec une distribution dans plus de 85
pays.
Tous nos produits répondent à des exigences de qualité
rigoureuses et à des dispositions légales en vigueur dans l’UE.
Afin de garantir la qualité, nous soumettons régulièrement nos
produits à des contrôles de qualité supplémentaires, tant par
notre propre service qualité que par un service qualité externe.
Dans le cas improbable d’un défaut malgré toutes les
précautions, il est possible d’invoquer notre garantie (voir les
conditions de garantie).
Conditions générales concernant la garantie sur les
produits grand public (pour l’UE) :
• tout produit grand public est garanti 24 mois contre tout vice
de production ou de matériaux à dater du jour d’acquisition
effective ;
• si la plainte est justifiée et que la réparation ou le
remplacement d’un article est jugé impossible, ou lorsque les
coûts s’avèrent disproportionnés, Velleman® s’autorise à
remplacer ledit article par un article équivalent ou à rembourser
la totalité ou une partie du prix d’achat. Le cas échéant, il vous
sera consenti un article de remplacement ou le remboursement
complet du prix d’achat lors d’un défaut dans un délai de 1 an
après l’achat et la livraison, ou un article de remplacement
moyennant 50% du prix d’achat ou
le remboursement de 50%
du prix d’achat lors d’un défaut après 1 à 2 ans.
• sont par conséquent exclus :
- tout dommage direct ou indirect survenu à l’article après
livraison (p.ex. dommage lié à l’oxydation, choc, chute,
poussière, sable, impureté…) et provoqué par l’appareil, ainsi que
son contenu (p.ex. perte de données) et une indemnisation
éventuelle pour perte de revenus ;
- tout bien de consommation ou accessoire, ou pièce qui
nécessite un remplacement régulier comme p.ex. piles,
ampoules, pièces en caoutchouc, courroies… (liste illimitée) ;
- tout dommage qui résulte d’un incendie, de la foudre, d’un
accident, d’une catastrophe naturelle, etc. ;
- out dommage provoqué par une négligence, volontaire ou non,
une utilisation ou un entretien incorrects, ou une utilisation de
l’appareil contraire aux prescriptions du fabricant ;
- tout dommage à cause d’une utilisation commerciale,
professionnelle ou collective de l’appareil (la période de garantie
sera réduite à 6 mois lors d’une utilisation professionnelle) ;
- tout dommage à l’appareil qui résulte d’une utilisation
incorrecte ou différente que celle pour laquelle il a été
initialement prévu comme décrit dans la notice ;
/