Eneo VK-1320/WDDG2 Installation And Operating Instructions Manual

1

Montage- und Betriebsanleitung

1/3” Videokameras im vandalismusgeschützten Domegehäuse

Tag/Nacht Domekamera – VKC-1327A/WDDG1, VKC-1327A/WDDG2

S/W Domekamera – VK-1320/WDDG2

Installation and Operating instructions

1/3” Video Cameras in Vandal Resistant Dome Housing

Day/Night Dome Camera – VKC-1327A/WDDG1, VKC-1327A/WDDG2

B/W Dome Camera – VK-1320/WDDG2

Mode d’emploi

Caméras Vidéo en boîtier antivandalisme 1/3”

Dôme Couleur Jour/Nuit – VKC-1327A/WDDG1, VKC-1327A/WDDG2

Dôme Caméra N/B – VK-1320/WDDG2

Instrucciones de manejo

Cámaras Vídeo en carcasa antivandalismo 1/3”

Camáras Domo Día/Noche – VKC-1327A/WDDG1, VKC-1327A/WDDG2

Camáras Domo en B/N – VK-1320/WDDG2

2

Inhalt

1. Sicherheitshinweise ........................................................................................................................................... 4

2. Allgemeine Beschreibung .................................................................................................................................

5

3. Montage des WDDG1-Gehäuses

......................................................................................................................... 5

4. Montage des WDDG2-Gehäuses

......................................................................................................................... 6

5. Anschlussbelegung ...........................................................................................................................................

6

6. Beschreibung der Einstellmöglichkeiten bei unterschiedlichen Kamerapaketen ..................................................

7

7. Fehlersuche und Fehlerbehebung

...................................................................................................................... 9

8. Technische Daten ..............................................................................................................................................

9

9. Maßzeichnungen .............................................................................................................................................36

Contents

1. Safety Instructions ........................................................................................................................................... 12

2. General Description

.......................................................................................................................................... 13

3. Mounting the WDDG1 Housing .........................................................................................................................

13

4. Mounting the WDDG2 Housing .........................................................................................................................

14

5. Connection Assignment ....................................................................................................................................

14

6. Description of the Possible Settings for Various Camera Packages ...................................................................

15

7. Troubleshooting and Rectiﬁcation of Faults ......................................................................................................

17

8. Speciﬁcations ..................................................................................................................................................17

9. Dimensional Drawings .....................................................................................................................................

36

Sommaire

1. Consignes de sécurité ...................................................................................................................................... 20

2. Description générale ........................................................................................................................................

21

3. Montage du boîtier WDDG1 ..............................................................................................................................

21

4. Montage du boîtier WDDG2 ..............................................................................................................................

22

5. Affectation des connexions ..............................................................................................................................

22

6. Description des possibilités de réglage des différents ensembles de caméras ..................................................

23

7. Recherche de défauts et remèdes ....................................................................................................................

25

8. Spéciﬁcations ..................................................................................................................................................25

9. Croquis ............................................................................................................................................................ 36

Page is loading ...

12

1. Safety Instructions

• Please read these safety and operating instructions before putting the camera into operation.

• Keep the manual in a safe place for later reference.

• Never operate the camera outside of the speciﬁcations as this may prevent the camera functioning.

• The cameras should never ointed with open iris towards the sun. (This can damage the sensor).

• Pay attention to safety when laying the connection cable and ensure that the cable is not subjected to heavy loads

or damage and that no moisture can get in.

• Protect your camera from contamination with water and humidity to prevent it from permanent damage.

Never switch the camera on when it gets wet. Have it checked at an authorized service center in this case.

• To disconnect the power cord of the 230VAC cameras, pull it out by the plug. Never pull the cord itself.

• Never open the device.

The warranty becomes void if repairs are undertaken by unauthorized persons.

• Maintenance and repair have to be carried out only by authorized service centers.

• Operate the camera only at a temperature range of -10°C to +40°C and at a humidity of max. 90%.

• The camera is equipped with an automatic gain control (AGC) which increases the sensitivity at low light levels.

Noisy pictures at these conditions are quite normal.

• Pictures including bright spotlights will cause perhaps vertical lines (smear) or soft edges (blooming) on the

monitor display. This happens most probably in automatic shutter mode (ESC).

This is not a defect but an effect caused by the CCD sensor.

• Be sure to put a silica-gel bag into the housing to avoid humidity due to temperature variance between inner and

outside of housing

• Contact your local dealer in case of malfunction.

• The warranty becomes void if repairs are undertaken by unauthorized persons. Do not open the housing.

• Installation, maintenance and repair have to be carried out only by authorized service centers. Before opening the

cover disconnect the unit from mains input.

• Only use original parts and original accessories from Videor E. Hartig GmbH.

• Use only a mild detergent to clean the housing.

Never use dilution or gasoline for this can cause permanent damage to the surface.

NOTE: The upper section of the housing may only be separated from the lower section by removing the

4 screws

NOTE: This is a class A digital device. This digital device can cause harmful interference in a residential

area; in this case the user may be required to take appropriate corrective action at his/her own

expense.

13

W

G

A

Wall / ceiling

K

2. General Description

• For ceiling and wall mounting

• Weatherproof and vandal-resistant design

• Clear Lexan Bubble with Inner Liner

• 1/3” CCD B/W or colour board camera with manual varifocal lens

• Automatic Shutter Control (AES)

• Automatic Gain Control (AGC)

• Back Light Compensation (BLC)

• Manual 3-axis Camera Adjustment

• Easy to mount for interior or exterior use

3. Mounting the WDDG1 Housing

Wall and ceiling mounting

Note

The operational side of the camera is mounted in the housing.

Prepare the mounting site for installation.

Loosen the 4 Torx screws on the housing, but do not completely remove them, and

remove the cap.

A

Screw holes Mark the position of the back of the housing W on the surface on which the device

is to be mounted. The screw holes A in the attached plate and/or on the back of the

housing W may be used as a template.

W

Back of housing Fix the back of the housing

W on the desired surface (plug and cross-head screws are

enclosed) and feed through the cable. 1/3” or 1/2” opening.

Note

When mounting on a ceiling, the camera must be installed within the housing.

G Housing cap Fasten housing cap G on the back of the housing.

Connection cable After connecting the power supply and attaching the coaxial cable to an appropriate

monitor, the camera is operational.

K

Cable feed Rubber washer for cable feed

14

Note

The operational side of the camera is mounted in the housing.

Prepare the mounting site for installation.

Loosen the 4 Torx screws on the housing, but do not completely remove them, and

remove the cap.

B

Screw holes Mark the position of the back of the housing W on the surface on which the device

is to be mounted. The screw holes B in the back of the housing W may be used as a

template.

W

Back of housing Fix the back of the housing

W on the desired surface (plug and cross-head screws are

enclosed) and feed through the cable. 1/3” or 1/2” opening.

Note

When mounting on a ceiling, the camera must be installed within the housing.

G

Housing cap Fasten housing cap

G on the back of the housing.

Connection cable After connecting the power supply and attaching the coaxial cable to an appropriate

monitor, the camera is operational.

K

Cable feed 1/3” and 1/2” socket. The 1/2” high-strength cable gland is included in the accessori

-

es. A dummy plug for the 1/3” socket is included.

Polarity of the DC plug

for all 12VDC cameras

5. Connection Assignment

The following connectors are mounted on the „eneo camera packages”, which are supplied with system cables

(video/DC):

Video output: BNC jack (white)

Power supply: Adapter bushing (green), for 12VDC/24VAC

4. Mounting the WDDG2 Housing

B

W

G

Wall / ceiling

K

Teﬂon

strip

15

6. Description of the Possible Settings for Various Camera Packages

Level and phase

control (A, B)

For

camera package

LEVEL potentio-

meter control

IRIS VKC-1327A/WDDG1

VKC-1327A/WDDG2

Iris control. Correct using potentiometer control for very

over-exposed images or where the contrast is too low.

Adjust using test image (min. 3,000Lux) and oscilloscope

to 1Vp-p signal.

PHASE potentio-

meter control for

vertical phase

PHASE VKC-1327A/WDDG1

VKC-1327A/WDDG2

Potentiometer control to adjust the phase for mains

synchronisation.

Adjustment to the same phasing when using several

cameras avoids disruptive post-synchronisation of the

monitor when using video change-over switches

(only possible with models with AC supply voltage).

LEVEL

A

PHASE

B

16

D, E For camera package:

VKC-1327A/WDDG1/2

DIP switch

(SW)

Function DIP switch ON DIP switch OFF

SW 1

NT/LL

Synchronisation

Internal Line lock The synchronisation

changes automatically,

depending on the mains

voltage. However, if SW1

is set to ON at 24VAC,

the camera operates in

internal synchronisation

mode.

SW 2

ELC/ALC Electronic shutter

activated

Manual shutter (1/50sec).

Only when using a video

signal controlled lens.

SW 3

BLC Backlight compensation

activated.

Backlight compensation is

deactivated.

SW 4

AGC Turbo AGC turbo mode is

activated.

Normal AGC operation

SW 5

FL Flickerless Flicker-free operation

is activated. Electronic

shutter at 1/50sec

Flicker-free operation is

deactivated. For shutter

operation, see SW2.

Only when operated at

50Hz.

SW 6

Sharpness Sharpness Standard setting

SW 7

Day/night If the lighting is

insufﬁcient, the camera

switches to night mode.

The camera constantly

operates in normal mode.

SW 8

IR mode The IR mode prevents

constant switching

between day and night

mode.

IR mode deactivated.

(Switches to B/W

operation)

Vertical

Phase

8 Position

DIP switch

D E

IRIS

LEVEL

Vertical

Phase

8 Position

Piano switch

IRIS

LEVEL

17

Fault Reason Action

The system is not functioning. No power supply Check and remedy if applicable.

No picture Incorrect connection

alignment

Check and correct if applicable.

Check and connect correctly if applicable.

No signal

Grainy or broken image Video connection to camera

damaged

Check and connect correctly if applicable.

Increase lighting

Poor lighting

Weak, milky image Light from the side Change camera position or possibly eliminate light

by tilting the housing using the integrated sun roof

or by screening, e.g. with a board. Then correct the

tilted image by turning the camera bracket in the

housing.

Service Maintenance and installation May only be carried out by authorised persons.

7. Troubleshooting and Rectiﬁcation of Faults

8. Speciﬁcations

Type VKC-1327A/WDDG1 VKC-1327A/WDDG2 VK-1320/WDDG2

Art. No.

92166 92167 91972

Video standard

CCIR/PAL

System

Day & Night

B/W

Sensor size

1/3”

Imager

CCD, Sony Super HAD Interline Transfer CCD, 1/3” Interline

Transfer CCD

Active picture elements

Approx. 440,000, (H) 752 x (V) 582 pixels Approx. 300.000,

(H) 512 x (V) 582 pixels

Synchronization

Internal/Line-lock (automatic detection depend on

power source)

Internal

Signal-to-noise ratio

48dB (AGC Off) 46dB (AGC Off)

Sensitivity

(at 50% video signal)

0,5Lux, (0.32Lux), Colour, 0.24Lux (0.15Lux), B&W at

F1.2 each (AGC-Turbo). Videor measurement result

0.14Lux, at F1.2; 0.3Lux

at F2.0 (Videor

measurement result)

Horizontal resolution

540TVL 480TVL 380TVL

Rotation range

manual: 360°

Automatic gain control (AGC)

Normal/Turbo (+6dB)

yes

Gamma correction

Approx. 0.45

Automatic shutter control

(AES)

1/50 ~ 1/100,000sec.

Integration rate

no

Digital Noise Reduction

(DNR)

no

18

Type VKC-1327A/WDDG1 VKC-1327A/WDDG2 VK-1320/WDDG2

Art. No.

92166 92167 91972

White balance (ATW)

2000 ~ 8000K, Automatic

–

Backlight compensation

BLC, On/Off switchable BLC, 60% center

weighted

IR cut ﬁlter

yes no

Video outputs (type)

CVBS, VBS VBS

Video outputs

1Vp-p, (C)VBS, 75ohms,

BNC

1Vp-p, CVBS, 75ohms 1Vp-p, VBS, 75ohms

Lens mount

integrated lens

Lens type

varifocal

Lens

F1.2/F2.0~360 / 3.8~9.5mm with galvanometer

controlled iris

F1.6 ~ 2.4/4 ~ 8mm

(ﬁxed iris)

Application range

Security

Nominal format size

1/3”

Aspherical technology

yes no

Focal length

3.8-9.5mm 4-8mm

Horizontal angle of view

74.2-30° 63-34°

Focus range

0.15m ~

Iris control

DC no

MOD (Minimum object

distance)

0.15m –

Filter screw size

Not available

Mount

n/a

Internal adjustments

8 Dip switches: Internal/Line-lock synchronization,

ELC/ALC (manual/motorized Iris), BLC ON/OFF, AGC

Normal/Turbo, Flickerless ON/OFF, Sharpness Normal/

Sharp, Day/Night mode Enabled/Disabled, IR mode

ON/OFF (Iteration reduction between day and night

position). 2 Potentiometers: Level for DC controlled

iris, V. phase adjustment (220∞ min. adjustable)

–

Cable connection

Video (BNC), Power (2-pin screw terminal) Video (BNC), 12VDC

(DC jack)

Cable entry

2x 8mm holes with

rubber glands

3/4” and 1/2” thread for conduit glands,

lock stopper included

Serial interfaces

no

Temperature range

(Operation)

-10°C ~ +50°C -10°C ~ +40°C

Heater

no Optional

Thermostat switching points

– +2.4°C On / +22°C Off

(heater kit 12V, #71664, optional)

Temperature range with

built-in heater

– -30°C ~ +50°C -30°C ~ +40°C

Protection rating

IP65, at installation according to the manual

Supply voltage

12VDC, 24VAC, (10.5 ~ 30VDC, 12 ~ 29VAC) 12VDC

Power consumption

Approx. 3.0watts Approx. 2.0watts

Vandalism resistant

yes

Bubble

Vandal resistant 3mm clear polycarbonate bubble with inner liner

19

9. Dimensional Drawings

See page 36

Type VKC-1327A/WDDG1 VKC-1327A/WDDG2 VK-1320/WDDG2

Art. No.

92166 92167 91972

Colour (bubble)

Clear

Camera ﬁxing

Board

Mounting

Housing assy, wall mount,

in-ceiling mount

Surface mount, wall mount

Housing

indoor housing, Die-cast

aluminium with clear

polycarbonate bubble

Outdoor housing, Die-cast aluminium with clear

polycarbonate bubble

Housing material

Aluminium

Colour (housing)

Pantone Cool Gray 1C

Dimensions

See drawings

Weight

Approx. 750g

Parts supplied

Mounting kit,

Torx wrench key

Mounting kit, 1/2” gland, blind covers,

Torx wrench key

Optional Accessories

The optional accessories currently available can be found on our Homepages: www.videor.com and

www.eneo-security.com

Page is loading ...

36

9. Maßzeichnungen – Dimensional drawings – Croquis – Medidas

Maße - Dimensions - Medidas: mm

WDDG1 WDDG2

# 991315

Technische Änderungen vorbehalten

Technical changes reserved

Sous réserve de modiﬁcations techniques

Sujeto a modiﬁcaciones técnicas

eneo

®

ist eine eingetragene Marke der Videor E. Hartig GmbH

Vertrieb ausschließlich über den Fachhandel.

eneo

®

is a registered trademark of Videor E. Hartig GmbH

Exclusive distribution through specialised trade channels only.

eneo

®

est une marque propriété de Videor E. Hartig GmbH

Distribution et vente à travers les distributeurs spécialisés.

eneo

®

es una marca registrada de Videor E. Hartig GmbH

Venta a traves de los distribuidores especializados.

Videor E. Hartig GmbH

Carl-Zeiss-Straße 8 · 63322 Rödermark/Germany

Tel. +49 (0) 6074 / 888-0 · Fax +49 (0) 6074 / 888-100

www.videor.com

www.eneo-security.com

86 ∅

52.5 ± 1

91.5 ± 1

40

8 ∅

85 ∅

64

86 ∅

91.5 ± 1

PT 3/4"

120

Eneo VK-1320/WDDG2 Installation And Operating Instructions Manual

This manual is also suitable for

Eneo VK-1320/WDDG2 Installation And Operating Instructions Manual

in other languages

Related papers

Other documents