Page is loading ...
Hoine
Deccrators
-- col
lect
ion
-
Craitsman
Corner
linen
Cabinet
Glass
Dooi
AssemblY
Ins
truct
ions
:- HDc i'tem
#Jr360
MFc
#i46'--
Please
read
over the instructions;
it will be a
time-saver
in the long run.
Note: Before Assembly,please
be sure
to work on a
soft,
flat surface
to avoid
any
damage
to the finish'
!;;lc i -'l
Parts
Check
List
Please
rennove
all the parts carefully
from the box.Thorougirly
clean
all wood surfaces
to remove
dust
and dirt that may have
settled
onto the finish.
@Top
Panet-l @Booton
Panel
-1 @Lelt
SidePanel-l
@li$t Side
Panel-l OUpprt
Fixed
shelf-l @i,liOote
Fixed
shelf-2
@Down
!ixed
shelf-l @Adjustable
shelfs-2
@Dra*er
ftont
panel-3 @Drawer
Left side
panel-3 @Drawer
Right
side
panel-3
,t-)..
@Drawer
bottorn
panel-3
@Door-t
@Drawer
Back
panel-3
Hardware
Check
List
Please
take
all the hardware
listed
below
out of the
ffi
hardware bag"
B
Hinges-
r.t
l,ni
/rl\
T_T
D Llr
Pull lland-l
bolts-8
(5/32*1i2't)
Ca
tches-1
k?
U
Round Screw-4
(6.14mm)
A
H6
Sheii support16
K'u
lland
-3
Drawer Bolis-3
C
Short
I
Pul l
, QE@
n
Long
ilat Screw-40
(#8t1")
G..fl
W
z
fiat Screw-8
(6*14mrn)
Page3-9
When
insetring
cam-bolts,the shoulder
should be flush with the
surface.Ifusing
an electric screwdriver,be
careful not too over tighten
the Cam-bolt,this
can cause
damagr:
.
Cam-bolt
Flush Cam-bolt not Flush
houlder
How to use Cam-Locks
Cam-locks
should
be inserted
into their designated
holes
with the arrow
pointing to the nearest
edge.The
coordinating
Cam-bolt
will be inserted
into the Cam-lock. Using the allen
wrench
or a flat-head
screwdriver,
tighten
the Cam-locks
until you feel resistance.
Over tightening
the
Camlock may break
the cam-lock.
r--\
-7
Pagc4-9
I
Ao.
l.Attach bottom panel
(2) fixed shelfs
(5&6&7) to the right side
panel
(4) rvith long flat screu'
(A) by using
screwdriver
as
figure shown'
2.Attach
Left side
panel
(3)
to the body
with Lonlg
flat screw
(A) by using screwdriver
as
figure
shown,
Pugc
5 9
3.Attach
Top panel
(1) to the
body with long flat screw
(A) by u.sing
screwdriver
as figure
shown.
A
AA
Page6-9
4.rum
rhe cabinet
updght,Attach
2 Hinge
(B) to door
(8)
and right Side Panel
(4) as lighten,
with 8 Short
Flat screw(c),by
using
screwdriver
as shown,
Attach
1 Hartd
pulls(D)
to Door
(8)
as tighten
,With
2 bolts
(E)
by screwdriver.
Attach
I Catches(F)to
Door(8)
and down
shelf
('/)
as tighten,With
4 Round Screw(G)
By
Screwdriver.
Inseit shelf
support
(I{) into the side
panels
(3&4),
F.'tt
the 2 adjustable sheifs
(9) on
them.tighten
with screw
Pagc?-9
5. Attatch
left side
panel
(11) Drawer
Flont
panel
(10)
and l drarver back
panel
(13).withflat
screw
(A) Then the I botiom panel
(14) into the grooves
on the
drawer back panel
drawer Side
panel
and Drawer Front. Attach right side
panel
(12) to the picec,
with screws
(A).Attach the
Drawer Hand Pu1l
(I) to the Drawer Front *'ith 2 Bolts(E).
Repeat assembly other 2 drarvers.
A1
Aa
@
(}
| ,z_^=\ I
| (IJ) 1.1-----..
I -,1 \-
-._:l
@
^Il
I
lageS-9
6. Put the drawer
into the wood slide some.Then
screw drawer
bolt(J) into the thread
holes
in
fixed shelf(5&6)
of Wood
slide.
THE ASSEMIILY i,:i
NOW COiv'IP:I-EIE"
Pirge 9 - 9
/
