Savant Shade Negative Reveal Pocket | 009-1653-01 1 of 2 45 Perseverance Way, Hyannis, MA 02601

Copyright © 2020 Savant Systems, LLC | 200219

Savant.com | 508.683.2500

The Savant Shade Negative Reveal Pocket system is designed to provide a clean transition from ceiling to shade enclosure. The system's

access panels are available in eight foot lengths and four or six inch widths. When shorter lengths are required, the access panel and

bracket can be cut to length in the field. For systems that require a shade that spans longer than eight feet, access panel joiner brackets

(included in kit) are available that allow two access panels to be joined together. Note: For lengths longer than eight feet, a shade

coupler (sold separately) is required. The SHA-C4IN and SHA-C6IN kits come complete with everything shown in the box contents

section below. Shade mount kits SHA-CB34 and SHA-CB5 can be purchased separately as needed.

pocket should be constructed with a solid material such as plywood or medium density fiber (MDF) board that can handle the weight of

the complete shade assembly, and then finished with wall board. Use the diagram below when building the pocket.

Box Contents (SHA-C4IN, SHA-C6IN)

(1) Shade Mount - Drive Side

(1) Shade Mount - Idler Side

(2) Plastic Cover for Shade Mount

(1) End Plug and End Plug Insert for the Shade Tubes

(1) Mount Bracket for Shade Motor

(4) #6 x 1 ½ inch pan head screws

(2) #6 x ⅜ inch flat head screws

(2) #6 x ¼ inch pan head screws

The SHA-CB34 shade mount kit contains all the pieces

oered in the SHA-C4IN and SHA-C6IN kits except

the Access Panel, Access Panel Bracket, Access Panel

Joiner Brackets, Euro screws, and #6 x ½ inch pan

head screws.

Access Panel Assembly

Access Panel

Mounting Bracket

Wall Board / Sheetrock

5/16 in

4 in

In cases where an Access Panel must be cut, use the two

1/4 inch pan head screws supplied with the kit to secure the

raised metal back down onto the wood.

1. Slide the two Access Panel Joiner Brackets into the slots on

one end of an Access Panel, leaving about half the bracket

protruding from end of panel.

2. Secure the brackets using the two Euro type screws

Access Panel Mounting Bracket. See image.

Quick Reference Guide

Savant Shade Negative Reveal Pocket | 009-1653-01 2 of 2 45 Perseverance Way, Hyannis, MA 02601

Copyright © 2020 Savant Systems, LLC | 200219

Savant.com | 508.683.2500

Install Shade Mounts Bracket

INSTEMP-xx). This template contains the holes and

required spacing needed to install any Savant shade

mount.

– Use painter's tape to reduce the chance of marking up

the walls whenever drilling is involved.

1. Slide the shade mount plastic cover over the mount. Ensure the mount is fully seated into the cover.

2. Determine the location in the shade pocket where the mount will be installed. Secure the drive side (motor side) mount to the wall or

ceiling of the pocket using two #6 x

1 ½ inch pan head screws included with the kit.

3. Using the drive side mount as a reference point, install the idler side mount using the remaining #6 x 1 ½ inch pan head screws. Take

(30.48 - 40.64 cm) along the panel. Savant recommends using a #6 or larger self tapping screw. Refer to diagram below.

Mount the Access Panel Bracket

2. Screw the bracket into the pocket using the appropriate screws for the material the pocket is made from. The bottom of the panel

should be mounted ⁄ inch (.79 cm) above the finished ceiling. Take care to ensure the panel is mounted level. See diagram above.

Follow instructions below to install the Access Panel Mounting Bracket into the pre-built shade pocket.