Savant Shade Negative Reveal Pocket | 009-1653-01 1 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2020 Savant Systems, LLC | 200219
Savant.com | 508.683.2500
The Savant Shade Negative Reveal Pocket system is designed to provide a clean transition from ceiling to shade enclosure. The system's
access panels are available in eight foot lengths and four or six inch widths. When shorter lengths are required, the access panel and
bracket can be cut to length in the field. For systems that require a shade that spans longer than eight feet, access panel joiner brackets
(included in kit) are available that allow two access panels to be joined together. Note: For lengths longer than eight feet, a shade
coupler (sold separately) is required. The SHA-C4IN and SHA-C6IN kits come complete with everything shown in the box contents
section below. Shade mount kits SHA-CB34 and SHA-CB5 can be purchased separately as needed.
Build Pocket
Joining two Access Panels
Access panels must first be joined together when the shade
pocket is longer than 8 feet. See steps below.
Cutting the Access Panel
Before installing the shade mounts, a pocket must be built into the ceiling where the shade and shade mounts will be housed. The
pocket should be constructed with a solid material such as plywood or medium density fiber (MDF) board that can handle the weight of
the complete shade assembly, and then finished with wall board. Use the diagram below when building the pocket.
Tube End Plug
(Idler Side)
Tube End Plug Insert
(Idler Side)
(4) 1 ½ inch ph screws (2) ⅜ inch fh screws
(2) ⅜ inch fh screws
(2) Access panel joiner brackets
(2) Euro Screws
(2) Shade Mounts
(2) Shade Mount
Plastic Covers
Mount Bracket
(Motor Side)
Pocket Access Panel Bracket
Pocket Access Panel
Box Contents (SHA-C4IN, SHA-C6IN)
(1) Shade Mount - Drive Side
(1) Shade Mount - Idler Side
(2) Plastic Cover for Shade Mount
(1) End Plug and End Plug Insert for the Shade Tubes
(1) Mount Bracket for Shade Motor
(4) #6 x 1 ½ inch pan head screws
(2) #6 x ⅜ inch flat head screws
(2) #6 x ¼ inch pan head screws
(1) 4 or 6 inch Access Panel
(1) 4 or 6 inch Access Panel Mounting Bracket
(2) Access Panel Joiner Brackets
(4) Flathead Euro screws
(1) Quick Reference Guide (this document)
Box Contents (SHA-CB34)
The SHA-CB34 shade mount kit contains all the pieces
oered in the SHA-C4IN and SHA-C6IN kits except
the Access Panel, Access Panel Bracket, Access Panel
Joiner Brackets, Euro screws, and #6 x ½ inch pan
head screws.
Access Panel Assembly
Access Panel
Mounting Bracket
Wall Board / Sheetrock
5/16 in
Fit the two
panels together
Screw Panel
Bracket to Pocket
Reveals Should Be Balanced
4 in (101.6 mm)
4 in
(101.6 mm)
In cases where an Access Panel must be cut, use the two
1/4 inch pan head screws supplied with the kit to secure the
raised metal back down onto the wood.
1. Slide the two Access Panel Joiner Brackets into the slots on
one end of an Access Panel, leaving about half the bracket
protruding from end of panel.
2. Secure the brackets using the two Euro type screws
included with the kit.
3. Slide the second access panel over brackets installed in
steps 1 and 2.
4. Mount the Access Panel Bracket into the pocket. See the
Mount Access Panel Bracket section below.
5. Fit the completed Access Panel assembly onto the installed
Access Panel Mounting Bracket. See image.
Savant® Shade Negative Reveal Pocket (SHA-C4IN, SHA-C6IN, SHA-CB34, SHA-CB5)
Quick Reference Guide
Savant Shade Negative Reveal Pocket | 009-1653-01 2 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2020 Savant Systems, LLC | 200219
Savant.com | 508.683.2500
HELPFUL! Before starting the process, review the diagrams below to ensure a trouble free install.
Install Shade Mounts Bracket
1.75 in.
(minimum)
1.75 in.
(minimum)
Horizontal Mount Vertical Mount
– Install shade mount so the center point is installed a
minimum of 1 ¾ inches (4.45 cm) from any obstructions.
If desired, this distance can be adjusted outward.
– To aid in the installation, a template is available (SHA-
INSTEMP-xx). This template contains the holes and
required spacing needed to install any Savant shade
mount.
– Use painter's tape to reduce the chance of marking up
the walls whenever drilling is involved.
1. Slide the shade mount plastic cover over the mount. Ensure the mount is fully seated into the cover.
2. Determine the location in the shade pocket where the mount will be installed. Secure the drive side (motor side) mount to the wall or
ceiling of the pocket using two #6 x
1 ½ inch pan head screws included with the kit.
3. Using the drive side mount as a reference point, install the idler side mount using the remaining #6 x 1 ½ inch pan head screws. Take
extra time to ensure that the two shade mounts are level with each other. Mounts that are not installed perfectly level will cause the
shade fabric to unroll unevenly.
4. With the shade mounts installed, the aluminum tube that the shade fabric is rolled onto can be cut. Refer to the Shades Installation
and Wiring Guide (009-1532) available on the Savant Customer Community for information on cutting the tubes to the correct
length for proper operation.
1. Lay the Access Panel Mounting Bracket on a flat solid surface. Starting at one end, drill appropriate sized holes every 12 to 16 inches
(30.48 - 40.64 cm) along the panel. Savant recommends using a #6 or larger self tapping screw. Refer to diagram below.
Mount the Access Panel Bracket
slot in pocket mount
12-16 inches
Bottom
To p
2. Screw the bracket into the pocket using the appropriate screws for the material the pocket is made from. The bottom of the panel
should be mounted ⁄ inch (.79 cm) above the finished ceiling. Take care to ensure the panel is mounted level. See diagram above.
Follow instructions below to install the Access Panel Mounting Bracket into the pre-built shade pocket.
With the pockets for the shades built and the Access Panel Mounting Bracket set in place, the shade mounts can be installed.
-
1
-
2
Savant SHA-C6IN-10 Reference guide
- Type
- Reference guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Savant SHA-B2MANUALWH-00 Reference guide
-
-
-
-
Savant SHA-B8CRSA-00 Reference guide
-
Savant SHA-MGEIGCTRL-00 Reference guide
-
-
-
-