Aaeon MIX-ALPSD1 User manual

Brand: Aaeon

Model: MIX-ALPSD1

Category: Motherboards

Type: User manual

Industrial Motherboard

MIX-ALPSD1

E22356

First Edition

September 2023

This document is copyrighted, 2023. All rights are reserved. The original

manufacturer reserves the right to make improvements to the products described

in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated, or transmitted

in any form or by any means without the prior written permission of the original

manufacturer. Information provided in this manual is intended to be accurate and

reliable. However, the original manufacturer assumes no responsibility for its use,

or for any infringements upon the rights of third parties that may result from its use.

The material in this document is for product information only and is subject to

change without notice. While reasonable efforts have been made in the preparation

of this document to assure its accuracy, the original manufacturer assumes no

liabilities resulting from errors or omissions in this document, or from the use of the

information contained herein.

The original manufacturer reserves the right to make changes in the product

design without notice to its users.

Acknowledgments

All other products’ name or trademarks are properties of their respective owners.

• AMI is a trademark of American Megatrends Inc.

• Intel®, Core™ are trademarks of Intel® Corporation.

• Microsoft Windows® is a registered trademark of Microsoft Corp.

• IBM, PC/AT, PS/2, and VGA are trademarks of International Business

Machines Corporation.

The original manufacturer reserves the right to make changes in the product

design without notice to its users.

All other product names or trademarks are properties of their respective owners.

iii

Contents

Chapter 1 Product overview

1.1 Package contents ......................................................................... 1-1

1.2 Features ........................................................................................ 1-1

1.3 Specications ............................................................................... 1-2

Chapter 2 Motherboard information

2.1 Before you proceed ..................................................................... 2-1

2.2 Motherboard layout ...................................................................... 2-2

2.3 Screw size ..................................................................................... 2-4

2.3.1 Component side .............................................................. 2-4

2.3.2 Solder side ...................................................................... 2-5

2.4 Central Processing Unit (CPU) ................................................... 2-6

2.4.1 Installing the CPU ........................................................... 2-7

2.4.2 CPU heatsink and fan assembly installation ................... 2-9

2.5 System memory ......................................................................... 2-11

2.6 Jumpers ...................................................................................... 2-13

2.7 Connectors ................................................................................. 2-18

2.7.1 Rear panel connectors .................................................. 2-18

2.7.2 Internal connectors ....................................................... 2-19

Chapter 3 BIOS setup

3.1 BIOS setup program .................................................................... 3-1

3.1.1 BIOS menu screen .......................................................... 3-2

3.1.2 Menu bar ......................................................................... 3-2

3.2 Main menu .................................................................................... 3-2

3.2.1 System Date [Day MM/DD/YYYY] .................................. 3-2

3.2.2 System Time [HH:MM:SS] .............................................. 3-2

3.3 Advanced menu ........................................................................... 3-3

3.3.1 CPUConguration .......................................................... 3-3

3.3.2 Trusted Computing ......................................................... 3-3

3.3.3 PTTConguration ........................................................... 3-4

3.3.4 SATAConguration ........................................................ 3-5

3.3.5 USBConguration .......................................................... 3-5

3.3.6 Hardware Monitor ........................................................... 3-5

3.3.7 SIOConguration ........................................................... 3-8

3.3.8 PCH-FWConguration ................................................... 3-9

3.3.9 NVMeConguration ........................................................ 3-9

3.3.10 Realtek PCIe GBE Family Controller

(MAC:00:E0:4C:68:00:03) ............................................................ 3-10

3.3.11 MAC:00E04C680003-IPv4NetworkConguration ...... 3-10

3.3.12 MAC:00E04C680003-IPv6NetworkConguration ...... 3-11

3.3.13 Realtek PCIe GBE Family Controller

(MAC:00:E0:4C:68:00:04) ............................................................ 3-11

3.3.14 MAC:00E04C680004-IPv4NetworkConguration ...... 3-11

3.3.15 MAC:00E04C680004-IPv6NetworkConguration ...... 3-12

3.3.16 Power Management ...................................................... 3-13

3.3.17 DigitalIOPortConguration ......................................... 3-14

3.4 Chipset menu ............................................................................. 3-14

3.4.1 SystemAgent(SA)Conguration ................................. 3-14

3.4.2 PCH-IOConguration ................................................... 3-15

3.5 Security menu ............................................................................ 3-16

3.5.1 Administrator Password ................................................ 3-16

3.5.2 User Password .............................................................. 3-16

3.5.3 Secure Boot .................................................................. 3-17

3.6 Boot menu .................................................................................. 3-19

3.6.1 BootConguration ........................................................ 3-19

3.6.2 FIXED BOOT ORDER Priorities .................................. 3-19

3.7 Save & Exit menu ....................................................................... 3-19

Appendix

Notices .......................................................................................................A-1

Contents

1-1

Chapter 1: General information

1.1 Package contents

Check your industrial motherboard package for the following items.

1 x Industrial Motherboard

1 x SATA Cable

1 x I/O Shield

NOTE: If any of the above items is damaged or missing, contact your

distributor or sales representative immediately.

1.2 Features

• Intel® Alder Lake-PS, 12th Gen Intel® Celeron & Core™ i3/i5/i7 processors,

LGA1700 socket; Max. TDP: 45W

• Two DDR5 (max. 64GB) SO-DIMM

• SATA 6.0 Gb/s port x 1, M.2 Slot (M-key; 2280) x 1, [PCIex4/NVMe]

• M.2 Slot (B-key; PCIe [x1]; 3042; USB 3.2) x 1, M.2 Slot (E-key; PCIe [x1] x 2;

2230; USB 2.0) x 1

• HDMI™, LVDS/eDP support

Chapter 1

Product overview

Chapter 1 Product overview

MIX-ALPSD1

1-2

1.3 Specications

System

Form factor

Mini ITX Form Factor, 6.7” x 6.7” (170 mm x 170 mm)

CPU

Intel® Alder Lake-PS, 12th Gen Intel® Celeron & Core™ i3/i5/i7

processors; LGA1700 socket; Max. TDP: 45W

Memory

2 x SO-DIMM, DDR5 (4800MHz, Max. 64GB) memory

Dual-channel memory architecture

I/O Chipset

NCT6126D

Ethernet

Realtek 8111H x 2

BIOS

256Mbit Flash ROM, AMI BIOS

Wake on LAN/PXE

Yes (WOL/PXE)

Watchdog Timer

1~255 steps by software program

H/W Monitor

Temperature Monitor on CPU/Chassis

Voltage Monitor on Vcore/5V

Fan Monitor on CPU/Chassis

Smart Fan Control

CPU Fan/Chassis Fan

Power State

S3, S4, S5

Expansion slot 1 x M.2 3042 B-Key (PCIe [x1], USB 3.2)

1 x M.2 2230 E-Key (PCIe [x1] x 2, USB 2.0)

TPM

InneonSLB9670TPM2.0onboard

Battery

Lithium battery

Power requirement DC 12V

Board size

6.7” x 6.7” (170 mm x 170 mm)

Weight

1.1 lb (0.5 Kg)

Operating

temperature

32°F ~ 140°F (0°C ~ 60°C)

Storage temperature

-40°F ~185°F (-40°C ~85°C)

Operating humidity

0%~90% relative humidity, non-condensing

Power compliance

N/A

Certicate

CE & FCC Class A

Graphics

Graphics chipset

Intel® UHD Graphics

Graphics

mutlti-display

HDMI™ x 2 + DP x 1, HDMI™ x 2 + LVDS x 1

HDMI™

HDMI™ 2.0; Up to 4096 x 2160 @ 60 Hz

DisplayPort

N/A

LVDS

Dual-Channel 18/24 bit LVDS via CH7513, up to 1920 x 1080

@60Hz, co-layout with eDP

eDP

Up to 4096 x 2160 @ 60 Hz,

co-layout with LVDS

Backlight control

PWM

(continued on the next page)

1-3

Chapter 1: General information

Internal I/O

Storage

1 x SATA (6.0Gb/s) port with 1 x SATA Power connector (1A)

1 x M.2 M key (2280), [PCIex4/NVMe]

Serial port

1 x RS-232/422/485 (supports 5V/12V/RI option)

3 x RS-232

USB

2 x USB 2.0 headers (support additional 4 USB 2.0 ports)

Display I/O 40-pin LVDS/eDP connector x 1 with Inverter (Default LVDS)

Fan

1 x CPU Fan header (4-pin)

1 x Chassis Fan header (4-pin)

Power 1 x 8-pin EATX 12V Power connector

1 x DC 12V Power jack

DIO

1 x 8-bit Digital I/O interface (In/Out programmable)

Others 1 x Clear CMOS jumper

1 x Front Panel header

1 x Chassis Intrusion header

1 x Buzzer on board

1 x AT/ATX Mode Selection jumper

1 x ME Disable jumper

1 x eDP/LVDS T-con IC Voltage Selection jumper

1 x eDP/LVDS Panel Backlight Voltage Selection jumper

1 x SATA Power connector

1 x LVDS Inverter connector

Audio 1 x HD Audio (via AAFP Header)

1xInternalSpeaker(2W/4OhmΩ)

Rear I/O

USB 3 x USB 3.2 Gen 2 ports

1 x USB 2.0 port

Display

2 x HDMI™ 2.0 ports

Ethernet

2 x RJ45 ports

Audio

1 x Line-out jack

1 x Mic-in jack

Others

OS Support Windows

11 64 bit, Windows

10 64 bit

NOTE:Specicationsaresubjecttochangewithoutnotice.

MIX-ALPSD1

1-4

2-1

Chapter 2: Motherboard information

Chapter 2

Motherboard information

2.1 Before you proceed

Take note of the following precautions before you install motherboard components

or change any motherboard settings.

CAUTION!

• Unplug the power cord from the wall socket before touching any

component.

• Before handling components, use a grounded wrist strap or touch a safely

grounded object or a metal object, such as the power supply case, to avoid

damaging them due to static electricity.

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded antistatic

pad or in the bag that came with the component.

• Before you install or remove any component, ensure that the ATX power

supply is switched off or the power cord is detached from the power

supply. Failure to do so may cause severe damage to the motherboard,

peripherals, or components.

Chapter 2 Motherboard information

MIX-ALPSD1

2-2

MIC_IN

LINE_OUT

HDMI2

HDMI1

LAN2

LAN1

USB3_12

USB3_3_USB2

DC_PWR1

ATX_AT

DDR5 SO-DIMM_B1 (64bit, 260-pin module)

DDR5 SO-DIMM_A1 (64bit, 260-pin module)

17.0cm(6.7in)

EATX_PWR1

EDP/LVDS

17.0cm(6.7in)

SATA6G_1

CHASSIS

CPU_FAN

SYS_FAN

F_PANEL

DIO

BATTERY_H

COM1

COM1_V

COM2 COM3 COM4

LGA1700

AMP_CON

ALC

897

AAFP

USB2_23

USB2_45

2280

2242

3042

DEBUG

SATA_PWR

INV

PNL_PWR

BKL_PWR

J1 J2

DIS_ME

CLRTC J4

SPI_1

M2_TYPE_M1

M2_TYPE_B1

M2_TYPE_E1

256Mb

BIOS

2 3

15161819

2022 21

2.2 Motherboard layout

Place this side

towards the rear

of the chassis

NOTE: Place four screws into the holes indicated by circles to secure the

motherboard to the chassis.

CAUTION! Do not overtighten the screws! Doing so can damage the

motherboard.

2-3

Chapter 2: Motherboard information

Connectors/Jumpers/Slots Page

1. ATX Power connector (8-pin EATX_PWR1) 2-19

2. Intel® LGA1700 CPU socket 2-6

3. DDR5 SO-DIMM slots 2-11

4. SATA Power connector (SATA_PWR) 2-29

5. SATA 6.0Gb/s port (7-pin SATA6G_1) 2-23

6. USB 2.0 headers (USB2_23, USB2_45) 2-24

7. eDP/LVDS connector 2-27

8. AT/ATX Mode Selection jumper (3-pin ATX_AT) 2-14

9. eDP/LVDS T-con IC Power Selection jumper (PNL_PWR) 2-16

10. LVDS Panel Backlight Power header (INV) 2-26

11. LVDS Panel Power Selection jumper (3-pin BKL_PWR) 2-14

12. CPU and System Fan headers (4-pin CPU_FAN, 4-pin SYS_FAN) 2-20

13. Chassis Intrusion header (4-1 pin CHASSIS) 2-15

14. System Panel header (10-1 pin F_PANEL) 2-23

15. COM Port headers (COM1~COM4) 2-25

16. COM1 Operating Mode Selection jumpers (2-pin J1~J4) 2-17

17. Clear CMOS jumper (CLRTC) 2-13

18. Intel® ME jumper (3-pin DIS_ME) 2-16

19. Digital I/O header (10-pin DIO) 2-26

20. COM1 Ring/+5V/+12V Selection header (COM1_V) 2-15

21. Battery connector (2-pin BATTERY_H) 2-21

22. Front Panel Audio header (AAFP) 2-22

23. AudioAmplierconnector(4-pinAMP_CON) 2-21

24. Debug Card connector 2-24

25. M.2 E-Key slot 2-28

26. M.2 M-Key slot 2-27

27. BIOS Programmable header (8-pin SPI_1) 2-20

28. M.2 B-Key slot 2-28

MIX-ALPSD1

2-4

2.3 Screw size

2.3.1 Component side

12.09

41.99

59.54

77.10

95.10

110.29

122.79

135.59

149.09

170.18

0.00

16.40

10.19

38.49

56.04

0.00

82.81

100.80

110.79

123.29

135.59

149.09

74.55

87.09

98.44

126.40

133.05

164.08

166.75

166.48

9.29

21.66

36.72

50.74

61.53

95.48

127.70

135.48

146.05

144.65

156.97

166.48

166.75

117.80

129.80

60.90

164.21

11.20

10.49

16.04

19.65

2.10

16.41

20.27

62.55

75.69

83.71

88.15

94.17

107.51

120.84

134.18

147.45

158.50

166.75

166.62

166.86

164.23

165.74

111.64

0.00

80.30

36.86

56.89

27.43

76.29

82.59

151.39

157.13

2-5

Chapter 2: Motherboard information

2.3.2 Solder side

10.16

0.00

33.02

72.64

165.10

6.35

0.00

163.83

5.49 6.35

163.83

70.28

81.79

141.49

129.28 127.28

91.28

89.28

148.28

43.49

135.23

46.89

46.86

150.64

MIX-ALPSD1

2-6

2.4 Central Processing Unit (CPU)

The motherboard comes with a surface mount LGA1700 socket designed for the

Intel® Alder Lake-PS, 12th Gen Intel® Celeron & Core™ i3/i5/i7 processors.

LGA1700

IMPORTANT: Unplug all power cables before installing the CPU.

CAUTION!

• Ensure that you install the correct CPU designed for LGA1700 socket only.

DO NOT install a CPU designed for other sockets on the LGA1700 socket.

• TheCPUtsinonlyonecorrectorientation.DONOTforcetheCPUinto

the socket to prevent bending the connectors on the socket and damaging

the CPU.

• Ensure that all power cables are unplugged before installing the CPU.

• Upon purchase of the motherboard, ensure that the PnP cap is on

the socket and the socket contacts are not bent. Contact your retailer

immediately if the PnP cap is missing, or if you see any damage to the

PnP cap/socket contacts/motherboard components. ASUS will shoulder

the cost of repair only if the damage is shipment/transit-related.

• Keep the cap after installing the motherboard. ASUS will process

Return Merchandise Authorization (RMA) requests only if the

motherboard comes with the cap on the LGA1700 socket.

• The product warranty does not cover damage to the socket contacts

resulting from incorrect CPU installation/removal, or misplacement/loss/

incorrect removal of the PnP cap.

2-7

Chapter 2: Motherboard information

2.4.1 Installing the CPU

CAUTION!

• Ensure that you install the correct CPU designed for LGA1700 socket only.

DO NOT install a CPU designed for LGA1155, LGA1156, LGA1151, and

LGA1200 sockets on the LGA1700 socket.

• ASUS will not cover damages resulting from incorrect CPU installation/

removal, incorrect CPU orientation/placement, or other damages resulting

from negligence by the user.

CAUTION! Take caution

when lifting the load lever,

ensure to hold onto the load

lever when releasing the

load lever. Letting go of the

load lever immediately after

releasing it may cause the

load lever to spring back

and cause damage to your

motherboard.

MIX-ALPSD1

2-8

2 3

2-9

Chapter 2: Motherboard information

2.4.2 CPU heatsink and fan assembly installation

To install the CPU heatsink and fan assembly

IMPORTANT: Apply Thermal

Interface Material to the CPU cooling

system and CPU before you install

the cooling system, if necessary.

CAUTION! Ensure to remove the

CPU Socket lever protector on the

lever latch before installing the

cooling system, failure to do so may

cause damages to your system.

MIX-ALPSD1

2-10

To uninstall the CPU heatsink and fan assembly

2-11

Chapter 2: Motherboard information

2.5 System memory

The motherboard comes with Small Outline Dual Inline Memory Modules (SO-

DIMM) slots designed for DDR5 (Double Data Rate 5) memory modules.

CAUTION! A DDR5 memory module is notched differently from a DDR, DDR2,

DDR3, or DDR4 module. DO NOT install a DDR, DDR2, DDR3, or DDR4

memory module to the DDR5 slot.

SO-DIMM_A1

SO-DIMM_B1

MIX-ALPSD1

2-12

To install a SO-DIMM

To remove a SO-DIMM

Page is loading ...

Aaeon MIX-ALPSD1 User manual

Brand: Aaeon

Model: MIX-ALPSD1

Category: Motherboards

Type: User manual

Download PDF

report

Aaeon MIX-ALPSD1 User manual

Aaeon MIX-ALPSD1 User manual

Related papers

Other documents