ekwb EK-Quantum Surface P360M X-Flow Installation guide

Brand
ekwb
Model
EK-Quantum Surface P360M X-Flow
Type
Installation guide
USER GUIDE
RADIATOR
EK-Quantum
Surface X-Flow Radiator Setup Configurations
Please note the installation of the product is intended to be undertaken
by an adequately trained and experienced person. You are installing the
product at your own risk. If you are not properly trained or experienced
or feel unsure about the installation procedure, please refrain from
installing the product yourself and contact our tech support for
assistance. We disclaim our liability for any damages to the product as
well as incidental, consequential, or indirect damages incurred due to
improper or inappropriate installation.
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
- 3 -
TABLE OF CONTENTS
EK-QUANTUM SURFACE X-FLOW RADIATOR SETUP CONFIGURATIONS 4
CROSSFLOW CONFIGURATION 1 4
CROSSFLOW CONFIGURATION 2 5
EXPLODED VIEW OF THE REMOVABLE COMPONENTS 6
SUPPORT AND SERVICE 7
SOCIAL MEDIA 7
- 4 -
EK-QUANTUM SURFACE X-FLOW RADIATOR SETUP CONFIGURATIONS
Please note that the X-flow radiators do not have a
classical U-shape coolant flow (inlet and outlet only on
one side of the radiator) but rather in crossflow (inlet
on one side, outlet on the other side). Crossflow port
setup on the X-Flow Radiator is mandatory! However,
you can choose the direction of the crossflow in your
custom loop.
CROSSFLOW CONFIGURATION 1
On the picture on the left you can see the first crossflow configuration.
You have to choose at least one of the ports on each side of the
radiator to be an inlet and an outlet.
CONFIG 1
OUTLET OPTIONS
INLET OPTIONS
EK-Quantum
Surface P360M X-Flow
- 5 -
CROSSFLOW CONFIGURATION 2
On the picture on the left you can see the second crossflow
configuration. You have to choose at least one of the ports on each
side of the radiator to be an inlet and an outlet.
It is mandatory to use the extenders on any inlet and
outlet position!
If transferred from the stock position of the radiator to another,
check if the extenders are tightened to avoid leakage!
EK recommends using the same number of inlets and
outlets for the most optimal performance.
The same crossflow port setup configurations applies for all
EK-Quantum Surface X-Flow radiator variants!
CONFIG 2
INLET OPTIONS
OUTLET OPTIONS
EK-Quantum
Surface P360M X-Flow
- 6 -
EXPLODED VIEW OF THE REMOVABLE COMPONENTS
EK-Quantum
Surface P360M X-Flow
2x QUANTUM SURFACE
EXTENDER
2x QUANTUM SURFACE END TANK SHROUD
(ALUMINIUM)
2x QUANTUM SURFACE
SIDE PLATE
(STAINLES STEEL)
6x QUANTUM SURFACE PLUG
8x TORX SCREW M3 x 6 mm
QUANTUM
SURFACE TANK
In case you need assistance, please contact:
https://www.ekwb.com/customer-support/
EKWB d.o.o.
Pod lipami 18
1218 Komenda
Slovenia - EU
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

ekwb EK-Quantum Surface P360M X-Flow Installation guide

Brand
ekwb
Model
EK-Quantum Surface P360M X-Flow
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents