EK-Quantum EK-Quantum Convection DDC Pump Heatsink User guide

Type
User guide

This manual is also suitable for

EK-Quantum EK-Quantum Convection DDC Pump Heatsink is a premium upgrade for your DDC pump, featuring a stylish aluminum cover and improved cooling performance. The included thermal pad ensures optimal heat transfer from the pump to the heatsink. Installation is a breeze thanks to the pre-cut thermal pad and custom-made screws. It's compatible with all EK-Quantum Kinetic DDC Series reservoirs, making it a perfect choice for creating a cohesive and visually stunning custom loop.

EK-Quantum EK-Quantum Convection DDC Pump Heatsink is a premium upgrade for your DDC pump, featuring a stylish aluminum cover and improved cooling performance. The included thermal pad ensures optimal heat transfer from the pump to the heatsink. Installation is a breeze thanks to the pre-cut thermal pad and custom-made screws. It's compatible with all EK-Quantum Kinetic DDC Series reservoirs, making it a perfect choice for creating a cohesive and visually stunning custom loop.

USER GUIDE
EK-Quantum
Convection DDC
This product is intended for installation only by expert users. Please
consult with a qualified technician for installation. Improper installation
may result in damage to your equipment. EK Water Blocks assumes no
liability whatsoever, expressed or implied, for the use of these products,
nor their installation. The following instructions are subject to change
without notice. Please visit our web site at www.ekwb.com for updates.
Before installation of this product please read important notice,
disclosure and warranty conditions printed on the back of the box.
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
DDC COVER DIMENSIONS 5
MAIN PARTS 6
PREPARING THE DDC PUMP 7
INSTALLING THE EK-QUANTUM CONVECTION DDC 8
SUPPORT AND SERVICE 10
SOCIAL MEDIA 10
- 4 -
MS - FLT DDC Cover Screw M4x34 (4 pcs)
Dumper Kinetic DDC M4x59 Screw (4 pcs)
M4 – Pump Top Mount Dumper
Pre-cut DDC thermal pad
34 mm
M4
58 mm
M4
Ø10 mm
5 mm
M4
BOX CONTENTS
Allen Key 2.5 mm (1 pc) Allen Key 2 mm (1 pc)EK-Quantum Convection DDC
Mounting Mechanism – You may not need all the screws,
mounting mechanism is universal!
- 5 -
DDC COVER DIMENSIONS
68 mm
68 mm
27.50 mm
- 6 -
MAIN PARTS
Position EAN Description
1
103328 ALU - FLT DDC Cover (Black Elox)
103327 ALU - FLT DDC Cover (Nickel)
103570 ALU - FLT DDC Cover (Natur Elox)
105059 ALU - FLT DDC Cover (Gold)
2100663 EK RGB Badge
3
103331
MS - FLT DDC Cover Screw M4 x 34 (Black Chrome)
103330 MS - FLT DDC Cover Screw M4 x 34 (Nickel)
105359 FLT DDC Cover Screw M4 x 34 (Gold)
48628 Blažilnik M4 - Pump Top Mount (V2)
5
103578 Kinetic DDC M4 x 59 Screw (Black Chrome)
103577 Kinetic DDC M4 x 59 Screw (Nickel)
105361 Kinetic DDC M4 x 59 Screw (Gold)
5
1
3
2
4
- 7 -
STEP 2
PREPARING THE DDC PUMP
STEP 1
Remove the original four (4) M4 x 25 screws of the DDC pump so that
the original cover can be removed from the assembly.
STEP 2
Then to remove the original pump cover, we recommend holding the
pump onto the reservoir by pressing the pattern in the middle. Then,
while pressing the pump onto the reservoir, remove the original
cover of the pump. If by accident the whole DDC pump is removed
or detached, please make sure that the O-ring seals are still properly
mounted. Any misplaced O-ring seal will cause coolant leakage!
If you are using EK-DDC Heatsink Housing, care for the thermal pad
between the DDC pump and the housing!
M4 x 25 SCREW
PRESS DOWN
REMOVE THE
ORIGINAL COVER
STEP 1
- 8 -
INSTALLING THE EK-QUANTUM CONVECTION DDC
STEP 1
EK has supplied you with additional pre-cut thermal pad. Place the
pre-cut thermal pad on the DDC pump by aligning the shape of the
pad to the DDC pump’s PCB.
STEP 1
Then place the EK-Quantum Convection DDC onto the DDC pump.
Be careful to rotate the ALU Cover so that the cables of the pump are
placed properly.
PRE-CUT
THERMAL PAD
- 9 -
STEP 2
Place the four (4) custom made M4 x 34 screws in their holes and
secure them with provided 2.5 mm Allen key. Do not use excessive
force while tightening the screws!
M4 x 34 SCREW
STEP 2
STEP 3
STEP 3
Following the same instructions for removing the original cover
of the DDC pump from the EK-Quantum Kinetic TBE DDC Series.
Then use the supplied 2 mm Allen Key for tightening four (4)
Dumper Kinetic DDC M4 x 59 Screws. Do not use excessive force
while tightening the screws! EK has also supplied you with four (4)
vibration absorbing M4 - Pump Top Mount Dumpers that can be
tightened on the M4 x 59 screws as shown on the picture.
DUMPER KINETIC
DDC M4 x 59 SCREW
M4 - PUMP TOP
MOUNT DUMPER
In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
For spare parts orders, refer to the page with “MAIN PARTS” where
you can find the EAN number of each part you might need.
Include the EAN number with quantity in your request. Mounting
Mechanism EAN can be found under “BOX CONTENTS”
Thermal pads are readily available in the EK shop
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

EK-Quantum EK-Quantum Convection DDC Pump Heatsink User guide

Type
User guide
This manual is also suitable for

EK-Quantum EK-Quantum Convection DDC Pump Heatsink is a premium upgrade for your DDC pump, featuring a stylish aluminum cover and improved cooling performance. The included thermal pad ensures optimal heat transfer from the pump to the heatsink. Installation is a breeze thanks to the pre-cut thermal pad and custom-made screws. It's compatible with all EK-Quantum Kinetic DDC Series reservoirs, making it a perfect choice for creating a cohesive and visually stunning custom loop.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI