American Dynamics ADSPOT Installation guide

SINGLE-POSITION OUTDOOR TRANSFORMER INSTALLATION GUIDE (8000-2573-29, REV. A)

1 of 4

ADSPOT Single-Position

Outdoor Transformer

Installation Guide

WARNING! This device contains a piece

of cardboard over the transformer to

protect it during shipping. Remove and

discard the cardboard before installing

this device.

IMPORTANT: Read Regulatory Requirements and

other declarations on page 4.

About the Product

This weather-tight box (Figure 1) contains a Class

2 limited power source providing power to the

SpeedDome Ultra and SpeedDome Optima

outdoor camera housings.

Note: Because customer requirements dictate the

placement of components, your Sales representa-

tive will supply this information separately.

Figure 1. Transformer and Box

Important Safeguards

A 15A, 2-pole, ganged disconnect device, which

also provides short circuit and overload protection,

and has a minimum 3mm open circuit clearance, in

accordance with the National Electrical Code,

Canadian Electrical Code and applicable local

codes must be installed at a location readily

accessible to the equipment.

(Ein 15A, 2-poliges, gekoppeltes Ausschaltgerät,

welches auch über einen Kurzschluß- sowie

Überbelastungsschutz verfügt, und einen minimum

3mm offenen Schaltabstand aufweist, nach

Übereinstimmung mit den Nationalen Elektrischen

Regelungen und Kanadisch Elektrischen

Regelungen sowie lokalen Regeln, muß an einem

Standort installiert werden, welcher einfachen

Zugang zum Gerät erlaubt.)

Outside elements. To keep outside elements from

entering the box, always mount it vertically with

cables exiting to the side or down.

Wire routing. Ensure wires from the secondary

and primary sides of the transformer do not cross

paths within the box.

Adding access holes to the enclosure. The box

meets the IP66 and NEMA 4 standards for

weatherproofing. To maintain this rating, do not drill

into the enclosure. Use outdoor rated conduit to

maintain the IP66 NEMA 4 rating.

See following pages for additional safeguards.

Transformer Label

Orange

Terminal Block

Knockouts

Mounting / Cover

Screw Hole

Fuse

Terminals

Ground

Terminal

SINGLE-POSITION OUTDOOR TRANSFORMER INSTALLATION GUIDE (8000-2573-29, REV. A)

2 of 4

Installation

The box can be mounted either indoors or outdoors

to any suitable vertical flat surface.

1. Remove the cover from the box.

2. Discard the cardboard covering the

transformer.

3. Using the box as a template, mark locations for

four mounting screws.

4. Drill holes. If in concrete, insert anchors.

5. Place the box in its mounting position. Then

insert a 1 inch #8 mounting screw (not

supplied) into each hole in the four corners of

the box and tighten to secure (Figure 3).

6. Run conduit and ac cable to the box and clamp

the conduit in place using fittings suitable for

outdoor use.

7. Connect the ac line to Euro-style input

terminals 1 and 4 on the transformer using

2.5mm

–1.5mm

(12–14 AWG) wire rated at

75°C minimum, and jumper the primary taps of

the transformer according to the input voltage

(Figure 2).

Note: The unit is built for 240Vac (jumper

across pins 2–3). For 120Vac, use the jumper

on the primary side and the jumper in the

install kit and place one jumper across pins

1–3 and one jumper across pins 2–4 as shown

below.

Figure 2. Transformer Wiring

24V

12V

GND

120V

Transformer Primary Jumper Settings

120Vac 1–3, 2–4

240Vac 2–3

8. Connect the low voltage power cable from the

camera dome to the secondary side of the

transformer.

WARNING! Do not run low voltage

cables adjacent to or in the same

conduit as line voltage mains power.

The length of this cable depends on the ac line

voltage. See the following table for cable

lengths based on worst-case low line voltages.

Worst-Case

Line

Voltages

.75mm

(18AWG)

1.25mm

(16AWG)

1.5mm

(14AWG)

90 Vac 30m (100') 50m (160') 80m (260')

102 Vac 60m (200') 100m (320') 160m (520')

180 Vac 30m (100') 50m (160') 80m (260')

204 Vac 60m (200') 100m (320') 160m (520')

Figure 3. Installing the outdoor dome power

source

Transformer

GND

N / L2 (Neutral)

L1 (Line)

Orange Connector

Gray

Connector

24Vac with

Center Tap

Ground

Knockout diameters, side of box:

15.5mm (.61in.) and 21mm (.83in.)

Knockout diameters, end of box:

23mm (.91in.) and 29mm (1.14in.)

SINGLE-POSITION OUTDOOR TRANSFORMER INSTALLATION GUIDE (8000-2573-29, REV. A)

3 of 4

Changing the Fuse

The outdoor dome power source has two fuses

(P/N 5111-0017-21). To reduce the risk of fire,

replace fuses only with the same type and rating

(3.15A type, IEC127, sheet III).

Wiring Diagram

L1 (Line)

N / L2 (Neutral)

GND

Blk

Wht

24V

12V

GND

120V

Transformer

Grn

Orange Connector

Gray

Connector

24Vac with

Center Tap

Ground

Class 2

24Vac

Connect the ac line

using 2.5mm -1.5mm

(12-14 AWG) wire rated

at 75°C minimum.

SINGLE-POSITION OUTDOOR TRANSFORMER INSTALLATION GUIDE (8000-2573-29, REV. A)

4 of 4

Specifications

Note: Transformer primary jumpers are field

changeable to support either 120Vac or 240Vac.

Electrical

Power source:.................... 120/240Vac @

50-60Hz

Input current:...................... 1.0A/0.5A

Output: ............................... 24Vac (29Voc),

2.5A max.

Listed Class 2

Certified Limited Power

Source

Mechanical

Environment....................... Indoor / Outdoor

Wall mounting options ....... Concrete, wood, sheet

rock

Dimensions (H x W x D) .... 175 x 125 x75mm

(6.9 x 4.9 x 3 inches)

Mounting area (H x W)....... 281 x 200mm

(11.1 x 7.9 inches)

Weight................................ 1.9kg (4.2 lbs)

Enclosure material ............. Impact resistant poly-

carbonate, non-metallic

Flammability rating...... UL 94-5V

Color .................................. Light gray

Cover fasteners ................. 4 captive screws

Cable access knockouts.... Eight 21 or 15.5mm

(0.83 or 0.61 inches);

Four 29 or 23mm

(1.14 or 0.91 inches)

Environmental

Weatherproof standard ...... NEMA 4 / IP66

Operating temperature: ..... –40°C to 50°C

(–40°F to 122°F)

Storage temperature:......... –40°C to 50°C

(–40°F to 122°F)

Relative Humidity:.............. 0 to 95% non-

condensing

Declarations

Regulatory Compliance

Reg ID ................................SV JBOX2

Safety .................................UL 60950

CSA C22.2 No. 60950

EN 60950

IEC 60950

FCC COMPLIANCE: This equipment complies with Part 15

of the FCC rules for intentional radiators and Class A digital

devices when installed and used in accordance with the

instruction manual. Following these rules provides reasonable

protection against harmful interference from equipment

operated in a commercial area. This equipment should not be

installed in a residential area as it can radiate radio frequency

energy that could interfere with radio communications, a

situation the user would have to fix at their own expense.

EQUIPMENT MODIFICATION CAUTION: Equipment

changes or modifications not expressly approved by

Sensormatic Electronics Corporation, the party responsible for

FCC compliance, could void the user's authority to operate the

equipment and could create a hazardous condition.

Other Declarations

WARRANTY DISCLAIMER: Sensormatic Electronics

Corporation makes no representation or warranty with respect

to the contents hereof and specifically disclaims any implied

warranties of merchantability or fitness for any particular

purpose. Further, Sensormatic Electronics Corporation

reserves the right to revise this publication and make changes

from time to time in the content hereof without obligation of

Sensormatic Electronics Corporation to notify any person of

such revision or changes.

LIMITED RIGHTS NOTICE: For units of the Department

of Defense, all documentation and manuals were developed at

private expense and no part of it was developed using

Government Funds. The restrictions governing the use and

disclosure of technical data marked with this legend are set

forth in the definition of “limited rights” in paragraph (a) (15)

of the clause of DFARS 252.227.7013. Unpublished - rights

reserved under the Copyright Laws of the United States.

TRADEMARK NOTICE: American Dynamics, Sensormatic,

and the Sensormatic logo are trademarks or registered

trademarks of Sensormatic Electronics Corporation. Other

product names mentioned herein may be trademarks or

registered trademarks of Sensormatic or other companies.

No part of this guide may be reproduced in any form without

written permission from Sensormatic Electronics Corporation.

MDR 1/03

American Dynamics ADSPOT Installation guide

Related papers

Other documents