Alpha innotec LWAV+ Owner's manual

Brand: Alpha innotec

Model: LWAV+

Category: Heat pumps

Type: Owner's manual

83024000cUK – Translation of the original operating manual

Air/Water Heat Pumps

Outdoor installation

Operating Manual

LWAV+ series

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

Table of contents

1 About this operating manual ...................... 3

1.1 Validity ....................................................... 3

1.2 Reference documents ............................... 3

1.3 Symbols and markings .............................. 3

1.4 Contact ...................................................... 4

2 Safety ............................................................... 4

2.1 Intended use ............................................. 4

  ............................ 4

2.3 Personal protective equipment ................. 4

2.4 Residual risks ............................................ 4

2.5 Disposal .................................................... 5

2.6 Avoid material damage ............................. 5

3 Description ...................................................... 6

3.1 As-delivered condition .............................. 6

3.2 Design ....................................................... 6

3.3 Accessories............................................... 7

3.4 Function .................................................... 7

4 Operation and care ....................................... 7

4.1 Energy and environmentally aware

operation ................................................... 7

4.2 Care .......................................................... 7

5 Delivery, storage, transport and

installation ....................................................... 8

5.1 Scope of supply ........................................ 8

5.2 Storage ...................................................... 8

5.3 Unpacking and transport ........................... 8

5.4 Installation ................................................. 9

6 Installation of hydraulic system .................11

7 Electrical installation ................................... 12

  ...................... 12

8.1 Heating water quality .............................. 12

 

circuit ....................................................... 13

9 Insulation of hydraulic connections ........ 13

  ......................... 13

11 Commissioning ............................................ 14

12 Maintenance ................................................. 15

12.1 Basic principles ....................................... 15

12.2 Maintenance as required ........................ 15

 ...... 16

12.4 Annual maintenance ............................... 16

13 Malfunctions ................................................. 16

14 Dismantling and disposal .......................... 16

14.1 Dismantling ............................................. 16

14.2 Disposal and recycling ............................ 16

Technical data / scope of supply ............ 17

Performance curves ................................... 18

LWAV+ 82R1/3 ................................................. 18

LWAV+ 122R3 .................................................. 20

Dimensional drawings ................................ 22

Installation plans .......................................... 24

Minimum clearances ........................................ 24

Connection set IPWAV vertical ........................ 25

Surface foundation ....................................... 26

Strip foundation ............................................ 27

Connection set WDFAV horizontal ................... 28

Surface foundation ....................................... 29

Strip foundation ............................................ 30

With condensate drain vertical ..................... 31

Condensate line........................................... 32

External condensate line connection ............... 32

Internal condensate line connection ................ 33

Hydraulic integration ................................... 34

LWAV+ with hydraulic station ........................... 34



hydraulic module ..................................... 35

 .................. 36

Keys hydraulic integration ................................ 37

Circuit diagrams ........................................... 38

LWAV+ 82R1/3 ................................................. 38

LWAV+ 122R3 .................................................. 40

EC Declaration of Conformity .................. 43

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

1 About this operating manual

This operating manual is an integral part of the unit.

 Before working on or with the unit, always read

the operating manual carefully and follow it for all

activities at all times, especially the warnings and

safety instructions.

 Keep the operating manual at hand at the unit and

hand it over to the new owner if the unit changes

hands.

 If you have any questions or if anything is unclear,

ask the local partner of the manufacturer or the

factory’s customer service.

 Observe all reference documents.

1.1 Validity

This operating manual refers solely to the unit identi-

 “Nameplate“,

page 7).

1.2 Reference documents

The following documents contain additional informa-

tion to this operating manual:

 Heat pump guide, hydraulic integration

 Operating manual of the heating and heat pump

controller

 Short description of the heat pump controller

 Operating manual of the extension board



 Log book

1.3 Symbols and markings



Symbol Meaning

Safety-relevant information.

Warning of physical injuries.

DANGER Indicates an imminent danger re-

sulting in severe injuries or death.

WARNING Indicates a potentially dangerous

situation, which can result in se-

vere injuries or death.

CAUTION Indicates a potentially dangerous

situation, which can result in mod-

erate or minor injuries.

IMPORTANT Indicates a potentially dangerous

situation, which can result in ma-

terial damage.

Symbols in the document

Symbol Meaning

Information for specialist

Information for operator



Prerequisite for an action



Single-step instruction for action

1., 2., 3., … Numbered step within a multi-step

instruction for action. Adhere to

the given sequence.

Additional information, e.g. a note

for making work easier, informa-

tion on standards



Reference to further information

elsewhere in the operating manual

or in another document

 List

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

1.4 Contact

Addresses for purchasing accessories, for servicing or

for answers to questions about the unit and this oper-

ating manual can be found on the internet and are kept

up-to-date:

 Germany: www.alpha-innotec.de

 EU: www.alpha-innotec.com

2 Safety

Only use the unit if it is in perfect technical condition

and only use it as intended, safely and aware of the

hazards and under full observance of this operating

manual.

2.1 Intended use

The unit is intended exclusively for the following func-

tions:

 Heating

 -

cessories)

 Cooling, reversible

 Intended use includes complying with the operating

  “Technical data / scope of supply”,

page 17) and the operating manual and ob-

serving the reference documents.

 If local regulations apply, observe: laws, stand-

ards and directives.

All other use of the unit is interpreted as not intended.

2.2 

The operating manuals supplied with the product are

intended for all users of the product.

The operation of the product via the heating and he-

at pump control and work on the product which is in-

tended for end customers / operators is suitable for all

age groups of persons who are able to understand the

activities and the resulting consequences and can car-

ry out the necessary activities.

Children and adults who are not experienced in hand-

ling the product and do not understand the necessa-

ry activities and the resulting consequences must be

instructed and, if necessary, supervised by persons

experienced in handling the product and who are re-

sponsible for safety.

Children must not play with the product.



All instructions and information in this operating manu-

-

sonnel.



out the work on the unit safety and correctly. Interfer-

-

ries and material damage.

 Ensure that the personnel are familiar with the lo-

cal regulations, especially those relating to work-

ing safely and in awareness of the hazard risks.

 Have work on the electrical and electronic compo-



“electrical” training.

 Have any other work on the system carried out



 Heating installers

 Plumbers

 

work)

During the warranty and guarantee period, servicing

and repair work may only be carried out by personnel

authorised by the manufacturer.

2.3 Personal protective equipment

There is a risk of cutting your hands on sharp edges

of the unit.

 Wear cut-resistant protective gloves during trans-

port.

2.4 Residual risks

Injuries caused by electric current

Components in the unit are live with fatal voltage. Be-

fore opening the unit casing:

 Disconnect the unit from power supply.

 Protect the unit against being switched back on

again.

 Residual voltage at the inverter. Wait for 90 sec-

onds before opening the unit.

Existing earthing connections within housings or on

mounting plates must not be altered. If this should ne-

vertheless be necessary in the course of repair or as-

sembly work:

 Restore earthing connections to their original con-

dition after completion of the work.

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

Risk of injury from moving parts

 .

Injuries and environmental damage due to

refrigerant

The unit contains harmful and environmentally dan-

gerous refrigerant. If refrigerant leaks out of the unit:

1. 

2. Notify authorised after sales service.

2.5 Disposal

Environmentally hazardous media

Improper disposal of environmentally hazardous me-



 Collect media safely.

 Dispose of the media in an environmentally sound

manner in accordance with to the local regula-

tions.

2.6 Avoid material damage

The ambient air at the heat pump’s installation site, as

well as the air drawn in as a heat source, must not

contain any corrosive components!

Constituents such as

 Ammonia

 Sulphur

 Chlorine

 Salt

 

can cause damage to the heat pump, which can even

result in the complete failure/total loss of the heat

pump.

Decommissioning/draining the heating

If the system/heat pump is decommissioned or drained

        

the condenser and any heat exchangers have been

drained completely for the event of freezing temper-

atures. Residual water in heat exchangers and con-

densers can result in damage to the components.

 Completely drain the system and the condenser,

and open vent valves.

 Blow them clear with compressed air, if required.

Improper action

Requirements for minimum scale and corrosion dam-

age in hot water heating systems:

 Professional planning and commissioning

 Closed system with regard to corrosion

 Integration of an adequately dimensioned pres-

sure maintenance

 

water corresponding to the VDI 2035 norm

 Regular servicing and maintenance

If a system is not planned, commissioned and operat-

ed in accordance with the given requirements, there

will be a risk of the following damage and malfunc-

tions:

 Malfunctions and failure of components, e.g.

pumps, valves

 Internal and external leaks, e.g. at heat exchangers

 Reduction in cross-section and blockages in com-

ponents, e.g. heat exchangers, pipes, pumps

 Material fatigue

   -

tation)

         -

mation of deposits, and associated noises, e.g.



 Observe the information in this operating manual

for all work on and with the unit.



and replenishing the heating circuit



heat generator and the heating components depend

decisively on the quality of the heating water.

-

cium deposits will form as scale. Lime scale deposits

accumulate on the heat transfer surfaces of the heat-

        -

crease. In extreme cases, the heat exchangers will be

damaged.

 Fill the system with deionised heating water





Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

3 Description

3.1 As-delivered condition

Packing unit 1

1 Side panels with

Packing unit 2

2 Base frame and sheet metal supports for the

fan module

3 Front panel and cover

4 



installation site!)

5 

6 Rear panel

3.2 Design

NOTE

This section essentially names the compo-



in this operating manual.

The heat pump module

1 Evaporator module

 

 

4 Cooling circuit module

The cooling circuit module

1 Electrical switch box

2 Plug connection to the fan module

3 Condenser

 

5 Expansion valve

 

7 Filter dryer

8 Inverter unit

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

Nameplate

The nameplate is attached at the following point on

the unit:

 on the back

It contains the following information at the very top:

 Model, item number

 Serial number

The nameplate also contains an overview of the most

important technical data.

3.3 Accessories

The following accessories are available for the unit via

the manufacturer’s local partner:

 Connection set, hydraulic

 Connection set, electrical

 Domestic hot water tank

 

 Room thermostat for switching the cooling function

 Dew point monitor for protecting a system with



 Room control panel for controlling the main func-

tions at the living quarters

 Extension board

3.4 Function

-

ergy for this process is ambient heat coming from the

outside air. The gaseous refrigerant is compressed



also the temperature. The gaseous refrigerant with



Here, the high temperature is transferred to the heat-

ing water and used in the heating circuit. The liquid re-

frigerant with high pressure and high temperature is

      -

perature drop and the process restarts.

The heated heating water can be used for the domestic

hot water or for heating the building. The temperatures

required and the use are controlled by the heat pump

controller. Any required reheating, support in screed

drying or increase in the domestic hot water temper-

ature can be carried out using an electric heating ele-

ment, which is activated by the heat pump controller

as required.

The integrated vibration decoupling for the hydraulic

system prevents structure-borne sound and vibrations

     

the building.

Cooling

Cooling is integrated in the units. The following op-

        operat-

ing manual of the heating and heat pump controller):

 Active cooling

Cooling in combination with hydraulic module or



of 18 °C. In combination with wall-mounted control-



 Cooling below 18 °C is only possible in the case



 The cooling function is controlled via the heating

and heat pump controller

 Switching over between heating and cooling

mode

4 Operation and care

NOTE

The unit is operated via the control panel of

 op-

erating manual of the heating and heat pump

controller).

4.1 Energy and environmentally

aware operation

The generally applicable requirements for energy and

environmentally aware operation of a heating system

also apply to the use of a heat pump. The most impor-

tant measures include:

 

 No unnecessarily high domestic hot water tem-



 -

tinuous ventilation), but instead open wide for a



 Always ensure that the controller setting is correct

4.2 Care

Wipe down the outside of the unit only using a damp

-

uid, neutral cleaning agent). Do not use any aggres-

sive, abrasive, acid or chlorine-based cleaning agents.

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

There is a risk of cutting your hands on sharp edges

of the unit.

 Wear cut resistant protective gloves.

The hydraulic connections are not designed for me-

chanical loads.

 Do not lift or transport the unit by the hydraulic con-

nections.

Transport the packing units preferably with a lift truck,

alternatively with a handcart or by carrying it.

 Do not tilt the heat pump module by more than 45°.

 The tensioning straps on the heat pump module

may only be used for carrying by hand.

Transport by crane

 Transport the packing units to the installation site

in packaged form and secured on a wooden pallet.

40-50°

 

Transport with a lift truck

 Transport the packing units to the place of instal-

lation in packaged for, and secured on a wooden

pallet.

Unpacking

1. -

age the unit.

2. Dispose of the transport and packaging materi-

al in an environmentally sound manner and in ac-

cordance with local regulations.

5 Delivery, storage, transport

and installation

IMPORTANT

Damage to the housing and the unit components

due to heavy objects.

 Do not place any objects on the unit that are heav-

ier than 30 kg.

5.1 Scope of supply

 Check supplied packages immediately on receipt

for visible signs of damage and completeness.

 Notify the supplier of any complaints immediately.

The separate package included contains:

 

 

 1 tube anti-friction agent

 1 HT sheet, DN 40 mm 87°

 1 protective cover for plug

 4 EPP screws

 

labels)

 Type stickers

In panel packages:

 Cover, front panel and rear panel  

packing unit 2)

 Side panels with    

unit 1)

 Cover, front panel, rear panel, side panels

5.2 Storage

 If possible, do not unpack the unit until immediately

before installation.

 Store the unit protected against:

 Moisture

 Frost

 Dust and dirt

5.3 Unpacking and transport

Notes on safe transport

 “Technical data / scope of supply”,

page 17). There is a risk of injuries or material dam-

age if the unit falls down or overturns.

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH



down

If the unit is not transported by a lift truck: Do not lift

 “5.1

Scope of supply“, page 8, pos. 2, 3 and 6) have



Optional separation of the fan module

NOTE

      

can be removed.

1. Disconnect the plug connections of the load and

bus cables at the top left on the switch box of the

cooling circuit for the fan module.

2. Remove the 4 screws from the fan module.

3. Remove the fan module and set it down safely.

4.    

cross-pieces.

1 Tensioning straps with openings for carrying

2 Polystyrene links

3 Screws on the fan module

Carrying the unit, transport using handcart

 The housing panels have been set down.

There are two circumferential tensioning straps on the

    

that can be used for lifting and carrying.

Two support crosspieces are clamped into the recess-

es at the sides for the air ducts for stability – do not re-

move them both until after transport.

Transport of the heat pump module with

a handcart

1. Only load the heat pump module on to the hand-

cart with the narrow side, left or right.

2. Secure the heat pump module on the handcart

with a tensioning strap.

3. Transport the heat pump module to the installa-

tion site.

5.4 Installation

CAUTION

In the air outlet area, the air temperature is

approx. 5 K below the ambient temperature.

Under certain climatic conditions an ice lay-

er can therefore develop in the air outlet area.

Install the heat pump so that the air blower

does not discharge into footpath areas

NOTE

Always comply with the installation plan for

the respective model. Note the size and mini-

mum clearances.

 Installation plan for the respective model, from

Page 24

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

NOTE

Install the unit so that the switch box side



NOTE

The noise immissions of the heat pumps must

be taken into account in the respective instal-

lation plans for air/water heat pumps. The re-

spective regional regulations must be com-

plied with.

Installation site requirements

 Perform installation outdoors only

 Clearance dimensions were complied with

 “Minimum clearances”, page 24

 Free air intake and blowing air are possible with-

out any air short-circuit.

 The surface is suitable for installation of the unit:

 The foundation is level and horizontal

 The surface and the foundation have a load-

 unit’s weight

 Ground surface in the air outlet area of the heat

pump is permeable to water

Unit installation

1. Align the unit base horizontally using the spirit level

and attach it to a strip foundation or full-area foun-

dation with 4 screws.

2. Unscrew the 4 levelling feet of the heat pumps by

2 turns.

3. Lift the heat pump over the unit base and place it

with the levelling feet in the holes provided in the

unit base. Push the levelling feet under the con-

striction of the holes.

4. Tighten the lock screws on the levelling feet

through the openings in the unit base using the



the unit base.

 Heat pump installation instructions

5. Remove the two tensioning straps.

6. Open the tension lock, turn the hook on the base

plate by 90°.

90°

 Heat pump installation instructions

7. Remove the two polystyrene crosspieces.

Attach the side panel, the rear panel,

the cover and the front panel

 Heat pump installation instructions

1. Hook the rear panel into the base plate.

2. Fit the cover.

3.         

pre-assembled). Fasten them in the front at the

center using a screw.

4. Attach the front panel.

5.         

front wall.

6. -

.

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

6 Installation of hydraulic system

1. Install the outside pipes of the heating circuit be-

neath the frost line.

NOTE

If an existing system is being replaced, the

old vibration decoupling may not be reused.

2. Flush the heating circuit thoroughly before con-

necting it to the heating system.

IMPORTANT

Damage to the copper pipes due to impermissible load!

 Secure all connections against twisting.

 Cross-sections and lengths of the pipes for the

heating circuit are adequately dimensioned.

 The free pressing of the circulation pumps pro-

duces at least the minimum throughput required for

   “Technical data / scope of supply”,

page 17).

 The hydraulic system must be equipped with a



on your model.

 “Technical data / scope of supply”, page 17

 The lines for the heating are fastened to the wall or



1 Heating water supply

 

3 Heating water return

3. Insert the vent at the highest point of the heating

circuit.

4.  “ Tech-

nical data / scope of supply”, page 17) are

complied with.

Condensate connection

The heating water drained from the safety valve and

the condensate that accumulates from the air must be

discharged in compliance with the applicable stand-

ards and regulations. Discharge of the condensate

and of the water drained from the safety valve into the

sewage system is permitted only via a funnel waste

trap, which must be accessible at all times.

 Condensate line connection

 Heat pump installation instructions

Hydraulic connection to the unit

Mount the corresponding connection set.

 Installation instructions for connection set

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

7 Electrical installation

Establishing the electrical connections

IMPORTANT

Irreparable damage to the compressor due to wrong



 -

sor’s load supply.

Basic information relating to the electrical

connection

       

company apply to electrical connections

 Equip the power supply for the heat pump with an

all-pole circuit breaker with at least 3 mm contact



  “Technical data /

scope of supply”, page 17)

 Comply with the electromagnetic compatibility



 Install unshielded power supply cables and





Connecting the heat pump module to

the hydraulic module, the hydraulic station

or the wall-mounted controller

The connection is established using the EVS 8 or EVS

accessory.

 EVS 8 load and bus connector with 8 m cable.

       -

mum of 2 additional EVS 8)

 EVS 8 installation instructions

 EVS: Load and bus connector.

Cable on site, maximum cable length of 30 m.

The bus cable must be a shielded cable of at least

4 x 0.5 mm².

As load line:

 For the 12 kW unit a 5 x 2.5 mm² cable with

protective conductor

 For the 8 kW unit a 3 x 2.5 mm² cable with pro-

tective conductor

 EVS installation instructions

1. Route the two plug-in connections of the load and

bus cables to the slots on the heat pump module.

2. Join the connections.

3. Fit the cover for the plug connections.

8 

8.1 Heating water quality

NOTE

 For detailed information refer, among

other things, to the VDI Guidelines

2035 “Vermeidung von Schäden in

 

damage in hot water heating systems)

 Required pH value: 8.2 …

for aluminium materials:

pH value: 8.2 … 8.5

 Fill the system with deionised heating water





Advantages of low-salt operation:

 Low corrosion-promoting properties

 No formation of mineral scale

 Ideal for closed heating circuits

 

the system

 If the required water quality is not achieved, con-

sult a company specialising in the treatment of he-

ating water.

 Keep a system log for hot water heating systems

       

2035).

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

Antifreeze in the heating circuit

For air/water heat pumps installed outdoors, it is not

-

ating circuit.

The heat pumps have safety devices that prevent the

water from freezing, even when the heating is swit-



switched on and is not disconnected from the mains.

Should there be a risk of frost, the circulation pumps

are activated.

The following points must be observed if antifreeze is

added, depending on the concentration of the mixture:

 Heat output of the heat pump is reduced

 COP value becomes worse

 In the case of on-site circulating pumps, the deliv-

  -



 The compatibility of the material of the compon-

ents used with the antifreeze mixture must be en-

sured

8.2 

the heating circuit

 Outlet pipe of the safety valve is connected.

 Ensure that the response pressure of the safety

valve is not exceeded.

NOTE

The venting program on the controller can

-

ing process. It is possible to control individual

circulation pumps and even the changeover

valve via the venting programs. As a result it is

not necessary to remove the valve motor.

1. Vent the system at the highest point.

2. Vent the heat pump at the hydraulic connection set.

9 Insulation of hydraulic

connections

Insulate hydraulic lines in accordance with the local

regulations.

1. 

2. Perform a pressure test and check for leaks.

3. Insulate external piping on site.

4. 

5. -

sible in combination with the wall-mounted control-



6. Insulate the condensate drain in a frost-proof

manner.

7. Fit the cover hood on the connection set.

8. The unit must be completely closed on all sides to

ensure rodent protection.

10 

NOTE

 The activities in this section are only nec-

essary for the integration of the storage

tank in series.

 Complete the work steps quickly, other-

wise the maximum return temperature

could be exceeded and the heat pump will

switch to high-pressure fault.

 Turn the rotary-push button on the over-

-

      

the left to reduce it

 

cold condition).

The IBN assistant already provides the option, in the

event of the integration of the storage tank in series to

   -

lic system.



Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

The “Set bypass valve” menu item is set by default to

-

tivated.

 The UWP control signal is the indication of the

currently required pump capacity in %

 

accuracy +/- 200 l/h)

1.        

circuits

2. If the “Set bypass valve” menu item is set from

“No” to “Yes”, the circulation pump is activated

with 100% – and the pump starts up.

3. If the control signal UWP reaches 100%, close



   “Technical data / scope of supply”,

page 17) can be ensured.

1 Rotary-push button

 

4. If you exit the “Set bypass valve” menu or at the

latest after one hour, the circulation pump switch-

es back to standard regulation

5. Open valves to heating circuit.

11 Commissioning

CAUTION

Prior to commissioning the unit, the air

ow baes must be mounted and the fa-

cing panels closed.

 Relevant planning & design data of the system is

documented in full.

 The relevant energy supply company has been



 The system is air-free.

 Installation check using the general checklist has

been completed successfully.

1. -

pletely:

 

available at the compressor

 The system is installed and mounted according to

this operating manual

 The electrical installation has been carried out

properly according to this operating manual and

the local regulations

 The power supply for the heat pump is equipped

with an all-pole circuit-breaker with at least 3 mm



 The tripping current is complied with

 

 

 The pipe systems and components of the system

are tight

2.   

for the heat pump systems.

3. In Germany: Send notice of completion for heat

pump systems and general checklist to the man-

ufacturer’s factory customer service depart-

ment.

In other countries: Send notice of completion for

heat pump systems and general checklist to the

manufacturer’s local partner.

4. Arrange for the heat pump system to be com-

missioned by the manufacturer’s authorised after

sales service for a fee.

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

12 Maintenance

NOTE

We recommend that you conclude a mainte-

nance agreement with your specialist heating

company.

12.1 Basic principles

The cooling circuit of the heat pump does not require

any regular maintenance.



specify tightness checks beforehand and/or for a log

book to be kept for certain heat pumps.

 Ensure compliance with the local regulations re-



12.2 Maintenance as required

 Check and clean the components of the heating

circuit, e.g. valves, diaphragm expansion vessels,



 Test the function of the safety valve for the heat-

ing circuit

 Always regularly control for unimpeded air in-

feed accordingly. Constrictions or even blockages

which, for example occur

 when applying house insulation with polysty-

rene balls

      -

tons etc.)

 through foliage, snow, icing or similar weath-

er-related deposits

 

 

etc.)

and which must be prevented and/or removed im-

mediately

 Check at regular intervals that the condensate

can drain out of the unit freely, without obstruc-

tion. To this end, check the condensate pan in the

unit and the evaporator regularly for dirt/clogging

and clean as necessary

Check the evaporator and the condensate

pan and clean them, if required

1. Remove the front panel, the side panels and the

cover, thus gaining access to the cover of the



2. -

-

tor is visible and can be cleaned if necessary.

Heat source inlet

sensor

As an alternative, the fan module can be removed to

obtain additional access.

 “Optional separation of the fan module“,

page 9

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

12.3 

the condenser

        

manufacturer’s instructions.

 -

       

condenser thoroughly with water.

12.4 Annual maintenance

 Determine the quality of the heating water by

analysis. In the event of deviations from the speci-



13 Malfunctions

 Read out the cause of the malfunction via the diag-

nostic program of the heating and heat pump con-

troller.

 Consult the local partner of the manufacturer or

the factory’s customer service. Have the fault

message and unit number at hand.

14 Dismantling and disposal

14.1 Dismantling

 The unit is disconnected from the power supply

and protected against being switched back on

again.

 Collect all media safely.

 Separate components by their materials.

14.2 Disposal and recycling

 Dispose of environmentally hazardous media ac-

      

compressor oil).

 Ensure the correct recycling or disposal of unit

components and packaging materials in accord-

ance with the local regulations.

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

Performance data Values in brackets: (1 Compressor) LWAV+ 82R1/3 LWAV+ 122R3

Heating capacity | COP for A10/W35 acc. to EN14511 Partial load operation kW | COP

3,18 ı 5,25 5,50 ı 5,10

for A7/W35 acc. to EN14511 Partial load operation kW | COP 2,81 ı 5,03 5,29 ı 4,71

for A7/W55 acc. to EN14511 Partial load operation kW | COP 3,28 ı 2,85 9,36 ı 2,65

for A2/W35 acc. to EN14511 Partial load operation kW | COP 3,82 ı 4,19 5,00 ı 4,01

for A-7/W35 acc. to EN14511 Full load operation kW | COP 6,40 ı 3,17 8,50 ı 2,63

for A-7/W55 acc. to EN 14511 Full load operation kW | COP

4,93 ı 2,20 8,46 ı 2,05

Heating capacity for A10/W35 min. I max. kW | kW 2,90 ı 7,00 5,40 ı 11,0

for A7/W35 min. I max. kW | kW 2,80 ı 6,60 5,40 ı 11,0

for A7/W55 min. I max. kW | kW 2,50 ı 6,40 4,50 ı 11,0

for A2/W35 min. I max. kW | kW 2,60 ı 6,40 4,60 ı 10,3

for A-7/W35 min. I max. kW | kW 2,30 ı 6,50 3,60 ı 8,50

for A-7/W55 min. I max. kW | kW

1,80 ı 4,95 2,80 ı 8,50

Cooling capacity | EER for A35/W18 Partial load operation kW | EER 6,00 ı 3,00 8,50 ı 2,80

for A35/W7 Partial load operation kW | EER 3,60 ı 1,80 5,00 ı 1,80

Cooling capacity for A35/W18 min. I max. kW | kW 1,00 ı 6,00 2,00 ı 8,50

for A35/W7 min. I max. kW | kW 1,00 ı 4,50 2,00 ı 6,00

Operating limits

Heating circuit return min. | Heating circuit flow max. Heating within heat source min./max. °C 20 ı 45 20 ı 45

Heat source, heating min. I max. °C -22 ı 35 -22 ı 35

Additional operating points …

A-5 / W60 A-5 / W60

Sound

Sound power level inside min. | Night | max. dB(A) — ı — ı — — ı — ı —

Sound power level outside 1) min. | Night | max. dB(A) 43 ı 49 ı 53 46 ı 49 ı 52

Sound power level acc. to EN12102 inside | outside dB(A) — ı 50 — ı 51

Tonality | Low-frequency dB(A) | • yes – no — ı — — ı —

Heat source

Air flow rate at maximum external pressing | Maximum external pressure m³/h | Pa 2500 ı — 2900 ı —

Heating circuit

Flow rate (pipe dimensioning) I Min. volume buffer tank in series I Min. volume separation buffer tank l/h | l | l 1200 ı 60 ı 100 1900 ı 100 ı 200

Free pressing | Pressure loss | Flow rate bar | bar | l/h — ı 0,14 ı 1200 — ı 0,2 ı 1900

Max. allowable operating pressure bar 3 3

Circulation pump control range min. I max. l/h — ı — — ı —

General unit data

Total weight kg 150 163

Weight of heat pump module | Compact module | Fan module kg | kg | kg 88 ı — ı 16 104 ı — ı 16

Refrigerant type | Refrigerant capacity … | kg R410A ı 3,00 R410A ı 3,60

Electrics

Voltage code | all-pole fuse protection for heat pump *)**) … | A 1~N/PE/230V/50Hz ı B16 3~N/PE/400V/50Hz ı B16

Voltage code | Control voltage fuse protection **) … | A 1~N/PE/230V/50Hz ı B10 1~N/PE/230V/50Hz ı B10

Voltage code | Electric heating element fuse protection **) … | A — —

WP*): effect. Power consumption A7/W35 (partial load operation) EN14511 I Electric consumption I cosφ

kW | A

0,559 ı 1,09 ı 0,83 1,12 ı 2,40 ı 0,83

WP*): effective power consumption A7/W35 acc. to EN14511: min. I max. kW | kW 0,5 ı — 1,12 ı —

WP*): Max. machine current I Max. power consumption within the operating limits A | kW 16 ı 3,5 13 ı 6,0

Starting current: direct | with soft starter A | A < 5 ı — < 5 ı —

Degree of protection IP 24 24

Residual current circuit breaker if required type B B

Electric heating element output 3 | 2 | 1 phase kW | kW | kW — ı — ı — — ı — ı —

Circulation pump power consumption, heating circuit min. I max. W — —

Other unit information

Safety valve heating circuit | Response pressure included in scope of supply: • yes – no | bar — ı — — ı —

Buffer tank | Volume included in scope of supply: • yes – no | l — —

Heating circuit expansion vessel | Volume | Prepressure incl. in scope of supply: • yes – no | l | bar — ı — — ı —

Overflow valve | Changeover valve heating - domestic hot water integrated: • yes – no — ı — — ı —

Heating circuit vibration decoupling incl. in scope of supply or integrated: • yes – no • •

Controller I Heat quantity recording I Extension board incl. in scope of supply or integrated: • yes – no — ı • ı — — ı • ı —

813586 813587

*) compressor only, **) note local regulations 1) Indoor and outdoor installation.

For indoor installation: Intake 1.5m air duct, Blow-out 1.5m air duct + air duct bend (original accessories)

Technical data / scope of supply

LWAV+

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

823290 c

Legende: Legende:

Volumenstrom Heizwasser

Volumenstrom Kühlwasser

TempWQ Temperatur Wärmequelle TempWS Temperatur Wärmesenke

Qh min/max minimale/maximale Heizleistung Q0 min/max

Q0 min/max minimale/maximale Kühlleistung

Pel min/max minimale/maximale Leistungsaufnahme Pel min/max Pel min/max minimale/maximale Leistungsaufnahme

∆pmax maximaler Druckverlust ∆pmax Druckverlust Wärmepumpe

Bezeichnung: Bezeichnung:

Seite: 1 Seite: 1

Datei: 823290 Leistungs- Druckverlustkurven LW(A)V 82R1_3

ÄÄnndd..//ÄÄ..MM..//EErrsstteelllleerr//DDaattuumm

Leistungs-Druckverlustkurven

a / PEPxxx-2018 / Peplau / 09.04.2018

LW(A)V 82R1/3

b / PEPxxx-2018 / Peplau / 10.08.2018

Zeichnungsnummer:

823290

c / 030-2020 / ArPe / 15.04.2020

ÄÄnndd..//ÄÄ..MM..//EErrsstteelllleerr//DDaattuumm

Leistungs-Druckverlustkurven

823290 c

c / 030-2020 / ArPe / 15.04.2020

Datei: 823290 Leistungs- Druckverlustkurven LW(A)V 82R1_3

a / PEPxxx-2018 / Peplau / 09.04.2018

LW(A)V 82R1/3

b / PEPxxx-2018 / Peplau / 10.08.2018

Zeichnungsnummer:

823290

-25 -20 -15 -10 -5 0 5 10 15 20 25 30 35

Temp„ [°C]

Qh min/max [kW]

35°C

55°C

0,00

0,05

0,10

0,15

0,20

0,25

0,30

0 0,5 1 1,5 2 2,5 3

“ ” [m³/h]

∆pmax [bar]

-25 -20 -15 -10 -5 0 5 10 15 20 25 30 35 40

Temp” [C°]

Temp„ [°C]

-25 -20 -15 -10 -5 0 5 10 15 20 25 30 35

Temp„ [°C]

Pel min/max [kW]

35°C

55°C

10 15 20 25 30 35 40 45

Temp

[°C]

Q0 min/max [kW]

7°C

18°C

0,00

0,05

0,10

0,15

0,20

0,25

0,30

0 0,5 1 1,5 2 2,5 3

[m³/h]

∆pmax [bar]

5 10 15 20 25 30 35 40 45

Temp

[°C]

Temp

[°C]

10 15 20 25 30 35 40 45

Temp

[°C]

Pel min/max [kW]

7°C

18°C

Keys: 823290cKeys: 823290c

“”“” Volume ow rate heating waterVolume ow rate heating water

TempTemp

„„ Heat source temperatureHeat source temperature

∆pmax∆pmax max. free pressingmax. free pressing

Qh min/maxQh min/max min./max. heating powermin./max. heating power

Pel min/maxPel min/max min./max. power consumptionmin./max. power consumption

LWAV+ 82R1/3Performance curves / operating limits / heating

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

823290 c

Legende: Legende:

Volumenstrom Heizwasser

Volumenstrom Kühlwasser

TempWQ Temperatur Wärmequelle TempWS Temperatur Wärmesenke

Qh min/max minimale/maximale Heizleistung Q0 min/max

Q0 min/max minimale/maximale Kühlleistung

Pel min/max minimale/maximale Leistungsaufnahme Pel min/max Pel min/max minimale/maximale Leistungsaufnahme

∆pmax maximaler Druckverlust ∆pmax Druckverlust Wärmepumpe

Bezeichnung: Bezeichnung:

Seite: 1 Seite: 1

Datei: 823290 Leistungs- Druckverlustkurven LW(A)V 82R1_3

ÄÄnndd..//ÄÄ..MM..//EErrsstteelllleerr//DDaattuumm

Leistungs-Druckverlustkurven

a / PEPxxx-2018 / Peplau / 09.04.2018

LW(A)V 82R1/3

b / PEPxxx-2018 / Peplau / 10.08.2018

Zeichnungsnummer:

823290

c / 030-2020 / ArPe / 15.04.2020

ÄÄnndd..//ÄÄ..MM..//EErrsstteelllleerr//DDaattuumm

Leistungs-Druckverlustkurven

823290 c

c / 030-2020 / ArPe / 15.04.2020

Datei: 823290 Leistungs- Druckverlustkurven LW(A)V 82R1_3

a / PEPxxx-2018 / Peplau / 09.04.2018

LW(A)V 82R1/3

b / PEPxxx-2018 / Peplau / 10.08.2018

Zeichnungsnummer:

823290

-25 -20 -15 -10 -5 0 5 10 15 20 25 30 35

Temp„ [°C]

Qh min/max [kW]

35°C

55°C

0,00

0,05

0,10

0,15

0,20

0,25

0,30

0 0,5 1 1,5 2 2,5 3

“ ” [m³/h]

∆pmax [bar]

-25 -20 -15 -10 -5 0 5 10 15 20 25 30 35 40

Temp” [C°]

Temp„ [°C]

-25 -20 -15 -10 -5 0 5 10 15 20 25 30 35

Temp„ [°C]

Pel min/max [kW]

35°C

55°C

10 15 20 25 30 35 40 45

Temp

[°C]

Q0 min/max [kW]

7°C

18°C

0,00

0,05

0,10

0,15

0,20

0,25

0,30

0 0,5 1 1,5 2 2,5 3

[m³/h]

∆pmax [bar]

5 10 15 20 25 30 35 40 45

Temp

[°C]

Temp

[°C]

10 15 20 25 30 35 40 45

Temp

[°C]

Pel min/max [kW]

7°C

18°C

Keys: 823290cKeys: 823290c

““

KWKW

Volume ow rate cooling waterVolume ow rate cooling water

TempTemp

WSWS

Heat sink temperatureHeat sink temperature

∆pmax∆pmax max. free pressingmax. free pressing

Q0 min/maxQ0 min/max min./max. cooling capacitymin./max. cooling capacity

Pel min/maxPel min/max min./max. power consumptionmin./max. power consumption

LWAV+ 82R1/3

Performance curves / cooling

Subject to change without notice | 83024000cUK – Translation of the original operating manual | ait-deutschland GmbH

Legende: Legende:

Volumenstrom Heizwasser

Volumenstrom Kühlwasser

TempWQ Temperatur Wärmequelle TempWS Temperatur Wärmesenke

Qh min/max minimale/maximale Heizleistung Q0 min/max

Q0 min/max minimale/maximale Kühlleistung

Pel min/max minimale/maximale Leistungsaufnahme Pel min/max Pel min/max minimale/maximale Leistungsaufnahme

∆pmax maximaler Druckverlust ∆pmax Druckverlust Wärmepumpe

Bezeichnung: Bezeichnung:

Seite: 1 Seite: 1

823291 c

Datei: 823291 Leistungs- Druckverlustkurven LW(A)V 122R3

ÄÄnndd..//ÄÄ..MM..//EErrsstteelllleerr//DDaattuumm

Leistungs-Druckverlustkurven

a / PEPxxx-2018 / Peplau / 09.04.2018

LW(A)V 122R3

c / 030-2020 / ArPe / 15.04.2020

b / PEPxxx-2018 / Peplau / 10.08.2018

Zeichnungsnummer:

823291

823291 c

ÄÄnndd..//ÄÄ..MM..//EErrsstteelllleerr//DDaattuumm

Leistungs-Druckverlustkurven

c / 030-2020 / ArPe / 15.04.2020

Datei: 823291 Leistungs- Druckverlustkurven LW(A)V 122R3

a / PEPxxx-2018 / Peplau / 09.04.2018

LW(A)V 122R3

b / PEPxxx-2018 / Peplau / 10.08.2018

Zeichnungsnummer:

823291

-25 -20 -15 -10 -5 0 5 10 15 20 25 30 35

Temp„ [°C]

Qh min/max [kW]

35°C 55°C

0,00

0,05

0,10

0,15

0,20

0,25

0,30

0 0,5 1 1,5 2 2,5 3

“ ” [m³/h]

∆pmax [bar]

-25 -20 -15 -10 -5 0 5 10 15 20 25 30 35 40

Temp” [C°]

Temp„ [°C]

-25 -20 -15 -10 -5 0 5 10 15 20 25 30 35

Temp„ [°C]

Pel min/max [kW]

35°C

55°C

10 15 20 25 30 35 40 45

Temp

[°C]

Q0 min/max [kW]

7°C

18°C

10 15 20 25 30 35 40 45

Temp

[°C]

Pel min/max [kW]

7°C

18°C

5 10 15 20 25 30 35 40 45

Temp

[C°]

Temp

[°C]

0,00

0,05

0,10

0,15

0,20

0,25

0,30

0 0,5 1 1,5 2 2,5 3

“

[m³/h]

∆pmax [bar]

Keys: 823291cKeys: 823291c

“”“” Volume ow rate heating waterVolume ow rate heating water

TempTemp

„„ Heat source temperatureHeat source temperature

∆pmax∆pmax max. free pressingmax. free pressing

Qh min/maxQh min/max min./max. heating powermin./max. heating power

Pel min/maxPel min/max min./max. power consumptionmin./max. power consumption

LWAV+ 122R3Performance curves / operating limits / heating

Page is loading ...

Alpha innotec LWAV+ Owner's manual

Brand: Alpha innotec

Model: LWAV+

Category: Heat pumps

Type: Owner's manual

Download PDF

report

Alpha innotec LWAV+ Owner's manual

Alpha innotec LWAV+ Owner's manual

Related papers

Other documents