ClosetMaid Mixed Material 6 Cube Installation guide

Brand
ClosetMaid
Model
Mixed Material 6 Cube
Type
Installation guide
INSTALLATION INSTRUCTIONS
© 2020 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | www.closetmaid.com01-61074-00 07/20
6-Cube Organizer
593300 | 593400 | 593500
2
SAFETY PRECAUTIONS
STOP
FOLLOW INSTRUCTIONS
CAREFULLY
Please do not return product to the retail store.
Forproduct assistance and warranty information
pleasecall Consumer Affairs at 1-800-874-0008.
Manufacturer Warranty
Manufacturer will replace any missing or damaged part
due to manufacturer defect for one year after purchase.
Pleasehave proof of purchase for warranty claims.
• Do not let any sharp objects touch or rub the surface of
theproduct.
• When assembling, do not let children play around the
working area.
• Please confirm all parts are correct before starting the
assembly process.
• DO NOT OVERTIGHTEN. DO NOT USE POWER TOOLS.
Power tools can overtighten screws and strip threads.
• Only use hex wrench provided.
We recommend you hand-tighten screws.
Please note location of predrilled holes.
BEFORE BEGINNING
•
Please read all instructions carefully.
•
Familiarize yourself with all parts (see“PARTS”) and check quantities.
•
Follow all safety precautions (see“SAFETY PRECAUTIONS”).
WARNING
CHOKING HAZARD FOR SMALL CHILDREN. This unit
contains small parts which could be a choking hazard for
small children. Children should be under adult supervision
at all times or serious injury could occur.
ALWAYS UNLOAD UNIT PRIOR TO MOVING THE UNIT.
The weight of personal belongings can cause the unit to
become unstable and either tip or collapse. Serious bodily
injury and/or damage to personal belongings may occur.
DO NOT OVERLOAD UNIT. If any shelf, top, or bottom
of unit bows or bends, it is overloaded. The shelf, top, or
bottom could collapse and cause serious bodily injury and/
or damage to personal belongings.
DO NOT CLIMB OR STEP ON THE UNIT. The unit may
become unstable and either tip or collapse. Serious bodily
injury and/or damage to personal belongings may occur.
DO NOT USE THIS UNIT AS A TELEVISION STAND.
Serious bodily injury and/or damage to personal
belongings mayoccur.
DO NOT MOUNT OR ATTACH ANYTHING TO THE SIDES,
REAR, OR FRONT OF THE UNIT. This can create a force
which can cause the unit to tip. Serious bodily injury and/or
damage to personal belongings may occur.
DO NOT STACK UNITS. Stacking of units can cause an
unsafe tip-over hazard which may cause serious bodily
injury and/or damage to personal belongings.
DO NOT HANG THIS UNIT ON THE WALL. The product
structure is not designed for wall hanging. Serious bodily
injury, damageto personal belongings, and/or damage to
the wall may occur.
FOLLOW PROPER SAFETY PROCEDURES WHEN USING
POWER TOOLSAND LADDERS.
• PROTECT YOUR WORK SURFACE DURING ASSEMBLY.
This can prevent scratching or damage to table tops,
woodfloors, etc.
3
Name Size (Qty) Part Number
AA
Allen Wrench
4 mm. (1) 65649
BB
Hex Screw
M6 x 15 mm. (8) 65629
CC
Long Screw
M7 x 48 mm. (4) 65624
DD
X Brace Screw
M4 x 9 mm. (4) 62284
EE
X Brace Cap Nut
M4 x .7 mm. (4) 62285
FF
Stamped Wrench
M4 (1) 73498
GG
L-Bracket
51 mm. (2) 62280
HH
L-Bracket Screw
M4 x 15 mm. (2) 62281
II
Wall Mount Screw
M4 x 35 mm. (2) 62283
PARTS
Call 1-800-874-0008 for parts and service. For faster service, have the style number ready when calling.
TOOLS REQUIRED
HARDWARE PROVIDED
4
PARTS
Call 1-800-874-0008 for parts and service. For faster service, have the style number ready when calling.
PRODUCT
*Please note location of predrilled holes on each part.
A
B
C
C
D
D
D
D
E
F
Name Qty Part Number
A
Left Metal Side Panel 1 62391
B
Right Metal Side Panel 1 62301
C
Top/Bottom Wood Panel 2
D
Vertical Divider 4 62393
E
Wood Shelf 1
F
X Brace 1 62306
61156
(593300)
61158
(593500)
61157
(593400)
61197
(593300)
61199
(593500)
61198
(593400)
5
fig. 1
Connect metal side panels to bottom wood panel.
STEP 1
Hex Screw x4
Align both metal side panels (A & B) with the bottom wood panel (C) as shown. The top/bottom wood panels (C) will only
have holes on one side. Make sure the horizontal bars on each metal side panel are below the screw holes and facing
toward the inside of the assembly (fig. 1). The two X brace holes on the side of each panel should be facing toward the
back of the assembly.
Use the supplied allen wrench (AA) to secure both metal side panels (A & B) to the bottom wood panel (C) using two hex
screws (BB) per side.
*Please note location of predrilled holes on each part.
A
B
C
BB
AA
BB
BB
C
Allen Wrench x 1
AA
6
Place bottom vertical dividers.
STEP 2
*Please note location of predrilled holes on each part.
Align two vertical dividers (D) with the holes on the bottom wood panel (C) as shown.
Push dividers into place.
C
D
D
7
Attach wood shelf.
STEP 3
*Please note location of predrilled holes on each part.
Align the holes on the bottom of the wood shelf (E) with the top of the vertical dividers (D). The wood shelf (E) should
rest on the lower horizontal bars of the metal side panels (A & B).
Push wood shelf into place.
Use the supplied allen wrench (AA) to secure both metal side panels (A & B) to the wood shelf (E) using two long screws
(CC) per side.
Long Screw x 4
A
B
D
D
E
CC
CC
Allen Wrench x 1
AA
8
Place top vertical dividers.
STEP 4
*Please note location of predrilled holes on each part.
Align two vertical dividers (D) with the holes on the top of the wood shelf (E) as shown.
Push dividers into place.
D
D
E
9
Connect metal side panels to top wood panel.
STEP 5
*Please note location of predrilled holes on each part.
Align the holes on the bottom of the top wood panel (C) with the top of the vertical dividers (D).
Use the supplied allen wrench (AA) to secure both metal side panels (A & B) to the top wood panel (C) using two hex
screws (BB) per side.
Hex Screw x 4
A
B
C
BB
BB
D
D
Allen Wrench x 1
AA
10
Secure X brace to back of unit.
STEP 6
Align the X brace (F) with the predrilled holes on the left metal side panel (A).
Secure the X brace to the left metal side panel (A) by using the stamped wrench (FF) to attach two X brace cap nuts (EE) to
two X brace screws (DD).
Align the X brace (F) with the predrilled holes on the right metal side panel (B).
Secure the X brace to the right metal side panel (B) by using the stamped wrench (FF) to attach two X brace cap nuts (EE) to
two X brace screws (DD).
X Brace Screw x 4
X Brace Cap Nut x 4
DD EE
*Please note location of predrilled holes on each part.
A
B
F
EE
DD
Stamped Wrench x 1
FF
11
Secure to wall using stud mounting.
Align top of unit with wall studs. Position L-bracket (GG) on wall stud and bottom of the top wood panel (C). The longer
side of the bracket will connect to the top wood panel and the shorter side will connect to the stud.
Secure the bracket (GG) to the top wood panel (C) using one L-bracket screw (HH). The screw should be mounted 1/2 in.
from the back edge of the top wood panel to ensure stability.
Secure the bracket to the stud using one wall mount screw (II).
Repeat steps for the other stud.
L-Bracket x 2
GG
16 in.
II
HH
GG
STEP 7
Wall Mount Screw x 2L-Bracket Screw x 2
HH II
1/2 in.
HH
C
C
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

ClosetMaid Mixed Material 6 Cube Installation guide

Brand
ClosetMaid
Model
Mixed Material 6 Cube
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents