Euroheat Tavo Aqua IN1215 Installation & Servicing Instructions Manual

Brand: Euroheat

Model: Tavo Aqua IN1215

Category: Fireplaces

Type: Installation & Servicing Instructions Manual

Euroheat Tavo Aqua IN1215 is a wood burning stove that can heat your home efficiently and safely.

It has been tested and certified to meet the highest safety standards, and it comes with a range of features to make it easy to use and maintain.

The Tavo Aqua IN1215 has a heat output of 5kW, making it suitable for small to medium-sized rooms. It has a large viewing window, so you can enjoy the flames while you stay warm.

The stove is also very efficient, with a burn time of up to 8 hours. This means you can load it up with wood less often, saving you time and effort.

Euroheat Tavo Aqua IN1215 is a wood burning stove that can heat your home efficiently and safely.

It has been tested and certified to meet the highest safety standards, and it comes with a range of features to make it easy to use and maintain.

The Tavo Aqua IN1215 has a heat output of 5kW, making it suitable for small to medium-sized rooms. It has a large viewing window, so you can enjoy the flames while you stay warm.

The stove is also very efficient, with a burn time of up to 8 hours. This means you can load it up with wood less often, saving you time and effort.

PART NUMBER

SERIAL NUMBER

Installation &

Servicing Instructions

TAVO AQUA

Wood Burning Stove

IN1215 Edition 1 June 2010

This manual must be used in conjunction with document IN1173.

The Wood and Mutlifuel Chimney and Installation Guide.

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Instructions Part Number IN1215 Ed 1

Contents

1 Important information prior to installation and commissioning ......................... 2

2 Scope of delivery ....................................................................................... 2

2.1 Transport/unpacking/checking ....................................................

3 Planning data ............................................................................................ 2

3.1 Dimensional drawings ...............................................................

3.2 Specications ...........................................................................

3.3 Combustion air supply ...............................................................

3.4 Components of the TAVO AQUA ..................................................

3.5

Calculation of heat requirement ..................................................

4 Setting up the boiler .................................................................................. 2

4.1 Requirements of the assembly area .............................................

4.2 Minimum distances ...................................................................

5 Assembly of the boiler ................................................................................ 2

5.1 Removal of the rear panel ..........................................................

5.2 Changing the ue outlet ............................................................

6 Connection to the chimney .......................................................................... 2

7 Hydraulic connection .................................................................................. 2

7.1 Thermal discharge safety device .................................................

7.2 Return ow boost (absolutely necessary) .....................................

7.3 Water system, decrease in performance ......................................

7.4 Expansion tank.........................................................................

7.5 Hydraulic system ......................................................................

8 Overview of the most important points ......................................................... 2

9 Customer services and spare parts ............................................................... 2

10 Your specialist company ............................................................................. 2

Instructions Part Number IN1215 Ed 1

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

IMPORTANT

 The installation of this appliance must comply with all local regulations, including those referring to National

and European Standards before it can be operated. The stove is not suitable for a shared ﬂue. However, for England

and Wales, only, the coming into force on 1st April 2002 of SI 2002 No 440 exempts the householder from this legal

requirement for the installation of solid fuel ﬁred appliance whose rated heat output is 50kW or less in a building

having no more than 3 storeys (excluding any basement) if a Competent Engineer is employed who is registered

under the Registration Scheme for Companies and Engineers involved in the Installation and Maintenance of

Domestic Solid Fuel Fired Equipment operated by HETAS Ltd. These registered Competent Engineers may also carry

out associated building work necessary to ensure that the installed appliance complies with Building Regulations

without involving the Local Authority Building Control Department.

 This appliance MUST be installed with a thermal store/buffer/accumulator. This is specialised work and may

need speciﬁc skills.

 Improper adjustment, alteration, maintenance or the ﬁtting of replacement parts not recommended by the

manufacturer can cause injury or property damage. Do not operate the stove with faulty seals or damaged glass.

 Due to the high operating temperatures of this appliance it should be located away from pedestrian trafﬁc and

away from furniture and draperies. Do not store paper or wood near the appliance. Any mats and rugs put in front

of the stove should be ﬁre proof and secured to prevent the possibility of tripping.

 Advise all persons as to the stove’s high surface temperatures. If it is possible for children or inﬁrm adults to

come into contact with the stove, ﬁt a suitable ﬁre guard.

 It is imperative that all air passageways into, out of, and within the appliance are kept clean. All permanent

ventilation into the room provided for the stove must remain clear and unobstructed at all times. Consideration must

be given to the need for extra ventilation if another heating source needing air is to be operated simultaneously.

If an extraction fan is proposed to be ﬁtted to a connecting area of the house, after the stove has been installed,

professional advice should be sought from a qualiﬁed engineer.

 The user should be advised that the appliance should be inspected regularly and the chimney cleaned at

least annually. More frequent cleaning may be required and the advice of a qualiﬁed chimney sweep should be

sought.

 Our range of stoves is capable of operating with outstanding efﬁciency if the ﬂue system is correct. Because so

little heat is wasted to the ﬂue it is possible that moisture within the products of combustion will condense if the

heat losses within the ﬂue way are too great and allow the ﬂue gases to cool. For this reason we recommend that

the stove is ﬁtted with a suitable ﬂue liner, the same diameter as the ﬂue spigot, to prevent the possibility of acidic

damage to the fabric of the chimney and damage to the stove which will reduce the longevity of the stove.

 When correctly installed, the stove is designed to produce heat, safely. It cannot do so if the installation is less

than absolutely stable, constructed of materials suitable for such an installation and consideration has not been

given to the possibility of people with less than ideal common sense operating it.

 Have the existing chimney swept by a chimney sweep. Although you will be lining the chimney, any deposits

left in the chimney will cause problems and may become a ﬁre hazard.

 Your attention is drawn to the precautions and responsibilities under the Health and Safety at Work Acts, and

whatever new legislation being introduced during the life of this document.

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Instructions Part Number IN1215 Ed 1

IMPORTANT STANDARDS/DIRECTIVES

In addition to the local re and building regulations the following standards and directives

must be observed when installing and commissioning the boiler:

ÖNORM M7550: Central heating boiler up to 100 °C: concepts, requirements, inspections,

designation of standards

ÖNORM M 7510 / 1: Directives for the inspection of central heating systems.

ÖNORM M 7510 / 2: Directives for the inspection of central heating systems; standards.

ÖNORM B8130: Safety devices.

ÖNORM B8131: Closed water-heating systems; safety-related requirements.

ÖNORM B8133: Safety-related requirements for hot water generation systems.

DIN 4751 Part 1: Safety-related equipment of heating systems with ow temperatures of up to

110°C (120°C in preparation).

DIN 4751 Part 2: Safety-related equipment of heating systems with ow temperatures of up to

110°C (120°C in preparation). Open and closed water heating systems up to

349 kW (300,000 kcal/h) with thermostatic fuse.

DIN 4751 Part 4: Safety-related equipment of heat generation systems with ow temperatures

of up to 120°C; closed water heating system with static levels of more than 15

m or nominal heat capacities of more than 350 kW.

DIN 1988: Potable water conduit systems in properties (technical regulations).

ÖNORM EN 303-5: Heating boiler for solid fuels, manually and automatically fed up to 300 kW.

concepts, requirements, inspections, designation.

ÖNORM M7135: Compressed wood and compressed bark in natural state - Pellets and

briquettes.

ÖNORM M7136: Compressed wood in natural state - wood pellets – quality control of transport

and storage logistics.

ÖNORM M7137: Compressed wood in natural state - wood pellets - Requirements for storage of

pellets at customers premises.

TRVB H118: Technical directive for preventive re protection for automatic biomass heating

systems.

Type test:

The TAVO AQUA was successfully tested by RWE Power AG according to EN 13240:2005. The

stove complies with the requirements for emissions according to Art. 15a B-VG concerning safety

precautions and the saving of energy.

The original type certicates are held by „SHT Heiztechnik aus Salzburg GmbH“.

Max. permitted operating pressure: 3.0 bar

Test pressure:

6.0 bar

Permitted ow temperature:

100°C

Instructions Part Number IN1215 Ed 1

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Part No: Part Description Part

Boiler

8B2520

8B2521

8B2522

8B2523

8B2524

8B2525

Boiler body TAVO steel jacket

Boiler body TAVO steel jacket, front, black

Boiler body TAVO soapstone

Boiler body TAVO soapstone, front, black

Boiler body TAVO Ananas

Boiler body TAVO Ananas, front, black

Accessories

2X2510

2X4216

2X4303

3F2508

3F2510

5C9220

9M1433

9M2433

Heat-resistant glove, silver with RIKA Logo

Brush 40/45 angular 529 lg

Ash damper

Thermostat with immersion sleeve for RLA

Thermal discharge safety device

Safety valve 3 Bar ¾” outlet

Operating instructions

Assembly instructions

Optional

accessories

A53100

Reﬂux heating assembly comprising:

• Heating pump

• Expansion tank

• Thermal mixing valve

• Shut off cocks

• Pipework, complete

Transport/unpacking/checking

After unpacking the delivery carefully check for completeness and any transport damage. Note any visible

deﬁciencies on the delivery note and report them to the manufacturer immediately.

Photographs of parts supplied

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Instructions Part Number IN1215 Ed 1

3 Planning data

Enclosed you will nd all the necessary data for the planning of the installation

3.1 Dimensional drawings

1243

586

528

100

1164

190

126

174

607.5

174 190

9090

157

341

384.5

419.7

490

341

201

217

132.5

Flue pipe optionally top or

at the rear

1 Connection of internal expansion tank*

2 Safety heat exchanger ON 1” AG

3 Safety heat exchanger OFF 1” AG

4 Flow connection 1” AG

5,6 Immersion sleeve ½” IG

7 Return port ¾” AG

Connection for external combustion air

125 mm

* Required only for internal reﬂux boost assembly and

closed off with a ½” cap.

Instructions Part Number IN1215 Ed 1

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

3.2 Speciﬁcations

Model/Type

Nominal heat capacity*

Water: Air relationship

Fuel capacity

Boiler water contents

Fill space

Max log length

max. permitted supply

temperature.

max operating pressure

max pressure on the safety

heat exchanger

Boiler weight

Flue pipe diameter

Minimum draught

requirement**

Supply and return ﬂow

Immersion sleeve

Free Air Requirement

B H

kW kW I. I. mm cm °C Bar Bar kg Ø Pa inch mm²

TAVO

AQUA

10 7:3 20 28 320 400 25 95 2.5 10 224 130 12 ¾ ½ 2750

*The type tested performance range is shown on the original test certiﬁcate and may deviate slightly from the

values given. **Pressure conversion from mbar to Pa

105 Pa [N/m²] = 1 bar conversion example: 20 Pa = 0.0002 bar = 0.2 mbar

Type

Performance range

Efﬁciency

Carbon monoxide

Organically bound

carbon

Nitrogen Oxide NOx Dust

related to the

input energy

related to

O2 content

related to the

input

energy

related to

O2 content

related to the

input

energy

related to

O2 content

related to the

input

energy

related to

O2 content

13% 13% 13% 13%

% mg/MJ mg/Nm³ mg/MJ mg/Nm³ mg/MJ mg/Nm³ mg/MJ mg/Nm³

TAVO

AQUA

NL 80.2 918 1412 28 43 62 95 17 26

Data for the chimney dimensions:

Fuel capacity 3.5 kg

Flue gas mass ﬂow 11 g/s

Mean ﬂue gas connection

temperature

260

Minimum supply pressure at

• Nominal heat capacity

• 0.8 times nominal output

12 Pa

10 Pa

Efﬁciency 80.2%

The ﬂue outlet on the TAVO AQUA is 125mm OD and

the ﬂue adapter supplied with the stove must be

used.

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Instructions Part Number IN1215 Ed 1

1 Hydraulic connections

2 Flue pipe connection

3 Safety heat exchanger

4 Front panel

5 Heat exchanger

6 Servicing cover

7 Combustion chamber

8 Filling doors

9 Front grate

10 Ash draw

11 Heating damper (primary air)

12 Adjustment knob (secondary air)

13 Connection, external combustion air

14 Connection of internal expansion tank*

* Required only for internal reﬂux boost

assembly and closed off with a ½” cap.

A Hearth in front of stove 300mm

B Hearth to side of free standing

stove

150mm

C From non-combustible surface 200mm

C From combustible surface 200mm

D From non-combustible surface 200mm

D From combustible surface 200mm

Components of the TAVO AQUA

Installation Clearances

Instructions Part Number IN1215 Ed 1

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Hearths

The stove should stand wholly above a hearth constructed of suitably robust materials and should be able to

accommodate the weight of the appliance and its unsupported ﬂue components. The materials should conform

to local Building Regulations and British Standards.

If the stove is not to stand in an appliance recess, a hearth made of non-combustible board/sheet material or

tiles of at least 12mm thick may be used as long as the ﬂoor can accommodate the weight of the appliance

and its unsupported ﬂue components. If it is installed on a wooden ﬂoor or similar, the ﬂoor must be covered

with a non-combustible material, a minimum of 12mm thick, to a distance of 300mm in front of the stove and

150mm to each side measuring from the closed door of the combustion chamber.

For further information on hearths available visit our web site www.euroheat.co.uk

Appliance independently tested to verify that the hearth temprature does not exceed 100°C

Non-combustable board

sheet material or tile

Combustible

material

300mm

12mm

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Instructions Part Number IN1215 Ed 1

1. The stove must always stand perfectly level. The provision of a suitable level hearth within the recess

is an important consideration when planning a ﬁreplace.

2. Sufﬁcient space should be allowed for service work.

3. At least the minimum clearance from inﬂammable materials and conforming to the current Building

Regulations.

4. Sufﬁcient space around the stove so that the controls may be operated without the risk of injury to

the operator.

5. Mounting brackets should be installed to facilitate the secure ﬁtting of a ﬁre guard, if one is to be

ﬁtted to protect the young, elderly or inﬁrm.

6. Curtains and soft furnishings should be a minimum of 1m from the stoves body or the surface

temperature of these furnishings must not exceed 65°C.

7. The mounting of expensive paintings, mirrors and plasma screen televisions above a ﬁreplace is not

recommended.

1/3 2/3

Fireplace Design

Do not be tempted to ﬁt the stove into an unsuitable ﬁreplace. Beyond the requirements of Building Regulations

and access to facilitate servicing the stove, providing a setting which will compliment a stove is not a luxury,

it is the practicality of making the most of an investment. A good builder or ﬁreplace specialist will be able

to transform even the most utilitarian of ﬁreplaces. Whether altering its proportions to those of the “Golden

Mean” ideal, see below, or exposing a wooden or stone lintel or simply removing superﬂuous detailing for a

comparatively small cost, and the result will be a pleasure for many years.

“Golden Mean”

1243

586

2/3

Instructions Part Number IN1215 Ed 1

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Combustion Air Supply

Free air requirement see the data table on page ?.

Fresh Air System

Instead of letting the air from the room into the stove for combustion, it is possible to take in fresh air from

outside and introduce this directly via a duct into the back of the stove.

Today, many modern dwellings are so airtight to conform with building regulations that it is an advantage to

attach a fresh air intake to the stove. This continually supplies the air for combustion while the stove is in use

but as the air is ducted directly into the back of the stove it stops cold fresh air mixing with the warm air in the

room chilling the room or causing draughts.

This ensures that the air extractor fan outlets in the kitchen and bathroom function optimally without effecting

the air required for combustion.

Fresh Air Systems are available. See www.euroheat.co.uk for further information.

The venting kit comprises of 2 jubilee clips, 1 meter of 100mm ﬂexible tube and the external cover vent.

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Instructions Part Number IN1215 Ed 1

Changing the Flue Outlet

The ﬂue outlet is mounted upwards at the factory. It can, however, be

turned so that the outlet faces to the rear.

• Remove the top plate and the rear panel from the boiler.

The top plate can be simply lifted off.

The rear panel is ﬁxed in place left and right of the rear

panel by two Allen screws, a 3mm Allen key is required.

Once these are removed tilt the rear panel backwards and

lift it off the lower brackets.

• Remove the two nuts on either side of the ue outlet and

rotate it by 180°.

• Ret the two nuts on the bolts and tighten them ensuring a

good seal is maintained.

• The ue adapter supplied with the stove MUST be used.

10mm ﬂue collar retaining nuts

Instructions Part Number IN1215 Ed 1

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Flue Draught Measurement

The TAVO AQUA is dependent on ﬂue draught. The minimum draught requirement is 12 Pa (0.05 in.H2O). If the

ﬂue draught is greater (>20 Pa / 0.08 in.H2O) then a draught regulator must be incorporated

into the ﬂue.

A ﬂue draught which is too low will result in the stove being difﬁcult to light, responding

only slowly to demands for increased output and unable to reach its full heating output. If

this is the case rectiﬁcation work of the chimney construction should be under taken. A ﬂue

draught which is too high will cause difﬁcult control conditions, and makes it possible to

over ﬁre the stove, which can seriously damage it. In this instance a ﬂue draught stabiliser

may need to be ﬁtted or if it is wind assisted excessive ﬂue draught a stabilizing cowl may

need to be ﬁtted.

The negative pressure created within the combustion chamber of the stove must be

measured using a test hole drilled into the ﬂue, as close to the stove as possible and before

any draught stabilizer that may be ﬁtted to the ﬂue.To ensure a constant air inlet size the

readings should be taken with the air inlet controls set at maximum.

Euroheat can supply the ﬂue measurement gauges. Order number MS026.

.05

1.0

.02

.01

.03

.04

.05

.06

.07

.08

.09

Note this is

not a water

gauge used to

measure gas

pressure.

Installation onto the Flue System

The connection of the stove to the ﬂue system is outlined in Document IN1173 Flue Systems and Installation

Planning Guide for Wood and Multifuel Stoves which is supplied with the stove.

Flue stabiliser closed

ﬂue draught between

0.05 to 0.08 in.H2O

Flue stabiliser open

ﬂue draught greater

than 0.08 in.H2O

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Instructions Part Number IN1215 Ed 1

7 Hydraulic connection

When connecting the boiler to the heating system ensure you follow the instructions in this document. This

applies especially to the safety devices.

7.1 Thermal discharge safety device

Use only thermal discharge safety valves, which have been checked and certiﬁed according to DIN 3440 and

whose ﬂow rate complies with the minimum requirements. It is important that the thermal discharge safety

valve is connected according to the circuit diagram, i.e. for normal heating operation the security battery is at

normal pressure, and is not therefore in a closed system. it must be connected without shutoff mechanism to

a pressurised mains water supply. The supply pressure must be at least 2 bar. The internal width of the feed

and discharge safety device of the thermal discharge safety device must not be less than its nominal width.

The drain line outlet must be unobstructed. Under no circumstances must the security battery be used as an

operational water heater.

According to DIN 4751, Sheet 2 the thermal discharge safety device must be inspected at least once per year

by a specialist. If any deﬁciencies are found the system must be thoroughly inspected.

Check the thermal discharge safety device:

Press the red cap against the valve, water must ﬂow into the drain (discharge hopper). A small discharge

indicates a malfunction. The system must be thoroughly inspected by a specialist, and a decalsiﬁer must be

used if necessary.

Operation of the thermal discharge safety device:

If the system overheats (95°C) a temperature valve opens the discharge safety device to the cold water inlet

pipe. Cold water ﬂows through the security battery, until a normal boiler temperature is reached again.

The security battery cannot be removed!

The permitted operational pressure of the security battery is 16 bar.

1 Domestic cold water connection

2 Non-return valve*

3 Filter*

4 Thermal discharge safety device

5 Thermal sensor of discharge safety device

6 Boiler (cooling) water supply

7 Boiler sensor connection

8 Boiler (cooling) water discharge

9 Discharge hopper/drain*

* Not included in scope of supply

Instructions Part Number IN1215 Ed 1

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

7.2 Return ﬂow boost (absolutely necessary)

The optimum value of the return ﬂow temperature at the boiler inlet is 60°C. The return ﬂow temperature must

be greater than 55°C, otherwise sooting and tar formation (with resulting corrosion) may occur. The return ﬂow

boost must be installed as near to the boiler as possible, so that the mixing temperature at the mixing valve

also corresponds to the return ﬂow temperature at the boiler.

Prior to commissioning, the hydraulic system must be ﬁlled with water. The installation speciﬁc operating

pressure lies between 1.0 bar and max. 2.0 bar.

Due to the limited space we recommend installation of the optionally obtainable reﬂux heating assembly (see

ﬁgure). This is incorporated inconspicuously into the boiler and only the connections with 1” external threads

are visible externally.

Rear view of the hydraulic connections

With integrated reﬂux heating set-up

Connections (from left to right):

• TAS on

• TAS off

• Safety valve off

• Boiler supply

• Boiler return ow

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Instructions Part Number IN1215 Ed 1

7.3 Water system, decrease in performance

The boiler must always be operated with a buffer reservoir, in order to store the accumulated energy (at

nominal output). In the event of too little heat consumption and the associated overheating of the boiler the

integrated safety devices will be activated.

7.4 Expansion tank

An absolute necessity for every heating installation is an expansion tank that is connected without shutoff

mechanism to the boiler/heating system. Calculation of the correct size is according to DIN 4751. As a rule of

thumb this is at least 100 l per 1000 l heating water.

The correct pressure of the expansion tank is approx. 1.5 bar, but it should always be 0.3 bar below the

installation pressure. Only in this way can it be ensured that no air will enter the heating system.

Air in the heating system prevents the correct and safe operation of the installation. If air continually enters

the system, for example owing to incorrect pressure in the expansion tank, then permanent corrosion damage

can occur.

7.5 Hydraulic system

The illustration below shows a typical connection example for the TAVO AQUA.

1. Boiler

2. External return ﬂow boost

3. Multi-storage

4. Thermal discharge safety valve

5. Fan

6. Safety valve

7. Drain (siphon)

8. Expansion tank

9. Shut off cock

Instructions Part Number IN1215 Ed 1

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

8 Overview of the most important points

• The TAVO AQUA is suitable for the combustion of rewood. Materials not suitable for combustion are:

pellets, wood dust, wood chips, solid- liquid- or gaseous fossil fuels, etc. In addition no PVC-containing

waste products, cardboard containers, paper, coated wood, litter, etc, must be burnt.

• The optimum boiler temperature is between 70°C and 75°C.

• The minimum boiler return ow temperature at the boiler inlet must not fall below 55°C (optimum

60°C) in operation, otherwise wood ﬁring can lead to the formation of condensation in the boiler

(causing soot and tar formation). The correct ﬁtting of a functional return ﬂow boost is a pre-condition

for the manufacturer’s warranty.

• The TAVO AQUA is a nominal output boiler. This means that it has no output regulation and must

be able to release the generated energy. A suitably dimensioned buffer reservoir is therefore

absolutely necessary!

• if no external combustion air supply is provided, ensure there is an adequate supply of fresh air in the

installation location/central heating room.

• When working on electrical/electronic equipment such as the motor, pumps, auger, suction fan or on

the control unit the complete system must be disconnected from mains power!

• The rewood must comply with the requirements in the operating instructions.

• Ensure that the wood is stored in a dry place.

• If there is a danger of frost, heating should be continued throughout the night and the buffer reservoir

should be loaded.

• If the system is shut down for a long period the boiler, ue duct and ue should be thoroughly

cleaned. The boiler door must be closed throughout this period and no water must be drained off.

The warranty is dependent on correct installation by a franchised installer (heating

engineer) and operation according to the instructions.

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Instructions Part Number IN1215 Ed 1

1 Customer services and spare parts

If you have any questions contact SHT Heiztechnik aus Salzburg GmbH customer services on Tel. +43 (0)662

450 444.

During the heating season customer services can be contacted on

Winter – Service – Hotline +43 (0)676 849 248 56

Your

SHT Heiztechnik aus Salzburg GmbH

A-5101 Salzburg-Bergheim, Rechtes Salzachufer 40

Tel. +43-662-450444-0

Fax. +43-662-450444-9

email [email protected]

Internet www.sht.at

Instructions Part Number IN1215 Ed 1

Installation & Servicing Instructions

TAVO AQUA

IN1215 Ed1

Court Farm Business Park, Bishops Frome,

Worcestershire WR6 5AY

Pre sales: 01885 491112

Technical: 01885 491117

Reception: 01885 491100

Need more info?

with over 10,000 pages of technical information, spare parts,

product shots, news and 1001 other things, - you will not ﬁnd

a more comprehensive solution to your queries, whatever

time of the day.

www.euroheat.co.uk

Euroheat Tavo Aqua IN1215 Installation & Servicing Instructions Manual

Brand: Euroheat

Model: Tavo Aqua IN1215

Category: Fireplaces

Type: Installation & Servicing Instructions Manual

Euroheat Tavo Aqua IN1215 is a wood burning stove that can heat your home efficiently and safely.

It has been tested and certified to meet the highest safety standards, and it comes with a range of features to make it easy to use and maintain.

The Tavo Aqua IN1215 has a heat output of 5kW, making it suitable for small to medium-sized rooms. It has a large viewing window, so you can enjoy the flames while you stay warm.

The stove is also very efficient, with a burn time of up to 8 hours. This means you can load it up with wood less often, saving you time and effort.

Download PDF

report

Euroheat Tavo Aqua IN1215 Installation & Servicing Instructions Manual

Euroheat Tavo Aqua IN1215 Installation & Servicing Instructions Manual

Related papers

Other documents