Paradyne 8820 Reference guide

Category
Networking
Type
Reference guide

This manual is also suitable for

8620 and 8820
Broadband Access Concentrator
SNMP Reference
Document No. 8000-A2-GB30-30
June 2004
A June 2004 8000-A2-GB30-30
Copyright © 2004 Paradyne Corporation.
All rights reserved.
Printed in U.S.A.
Notice
This publication is protected by federal copyright law. No part of this publication may be copied or distributed,
transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or
by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express
written permission of Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773.
Paradyne Corporation makes no representation or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Further, Paradyne Corporation
reserves the right to revise this publication and to make changes from time to time in the contents hereof without
obligation of Paradyne Corporation to notify any person of such revision or changes.
Changes and enhancements to the product and to the information herein will be documented and issued as a new
release to this manual.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor directly for any help needed. For additional
information concerning warranty, sales, service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:
î‚„ Internet: Visit the Paradyne World Wide Web site at www.paradyne.com. (Be sure to register your warranty at
www.paradyne.com/warranty.)
î‚„ Telephone: Call our automated system to receive current information by fax or to speak with a company
representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A., call 1-727-530-2340
Document Feedback
We welcome your comments and suggestions about this document. Please mail them to Technical Publications,
Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773, or send e-mail to userdoc@paradyne.com. Include the
number and title of this document in your correspondence. Please include your name and phone number if you are
willing to provide additional clarification.
Trademarks
ACCULINK, COMSPHERE, EtherLoop, FrameSaver, Hotwire, MVL, NextEDGE, OpenLane, Performance Wizard,
TruePut, and the Paradyne logo are registered trademarks of Paradyne Corporation. BitStorm, GrandVIEW,
GranDSLAM, Hotwire Connected, iMarc, ReachDSL, StormPort, and StormTracker are trademarks of Paradyne
Corporation. All other products and services mentioned herein are the trademarks, service marks, registered
trademarks, or registered service marks of their respective owners.
8000-A2-GB30-30 June 2004 i
Contents
About This Guide
î‚„ Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . . iii
î‚„ Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
î‚„ Product-Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
1 Network Management Specification
î‚„ SCP Card 3.2 (ATM) and 4.0 (IP) Network Management Interface . . 1
î‚„ Standards Compliance for SNMP Traps . . . . . . . . . . . . . . . . . . . . . . . 10
î‚„ Standards Compliance to SNMP MIBs . . . . . . . . . . . . . . . . . . . . . . . . 17
î‚„ Evolution of the Interfaces Group of MIB-II (RFC 2863) . . . . . . . . . . . 21
î‚„ Physical Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
î‚„ Link Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
î‚„ Network Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
î‚„ Configuration Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
î‚„ Timing and Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
î‚„ Access Control and Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
î‚„ Status and Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Index
Contents
ii June 2004 8000-A2-GB30-30
8000-A2-GB30-30 June 2004 iii
About This Guide
Document Purpose and Intended Audience
This reference manual contains the network management specification for the
8620 and 8820 Broadband Access Concentrators (BACs) managed by SCP cards
running Release 3.2 (ATM uplink) and Release 4.0 (IP uplink) and above. It is
designed for network managers who use SNMP in the course of installing,
configuring, monitoring, and troubleshooting BACs and associated cards.
Document Summary
A master glossary of terms and acronyms used in Paradyne documents is
available online at www.paradyne.com. Select Support → Technical Manuals →
Technical Glossary.
Section Description
Chapter 1, Network
Management Specification
Provides detailed information about the network
management interface of the 8620 and 8820 BACs.
Index Lists key terms, concepts, and sections in alphabetical
order.
About This Guide
iv June 2004 8000-A2-GB30-30
Product-Related Documents
Complete documentation for this product is available online at
www.paradyne.com. Select Support → Technical Manuals.
To order a paper copy of a Paradyne document, or to speak with a sales
representative, please call 1-727-530-2000.
Document Number Document Title
7890-A2-GB22 GrandVIEW EMS User’s Guide
8400-A2-GB20 Shelf Concentration and Processing (SCP) Card with ATM
Uplink User’s Guide
8400-A2-GB21 Shelf Concentration and Processing (SCP) Card with IP Uplink
User’s Guide
8620-A2-GN20 8620 Broadband Access Concentrator Installation Guide
8820-A2-GN20 8820 Broadband Access Concentrator Installation Guide
8000-A2-GB30-30 June 2004 1
Network Management Specification
1. SCP Card 3.2 (ATM) and 4.0 (IP) Network Management Interface
This document describes the SNMP support for the 8620 and 8820 Broadband Access
Concentrator (BAC) product. The product includes the following models:
These units are configurable from SNMP or through the TL1 Command Line Interface
using the following MIBS.
Table 1-1. Model Numbers for the BAC Product
Type Model Description Release
SHDSL 8985 ATM Card, 24 SHDSL Ports R3.0
ReachDSL-V3 8955 ATM Card, 24 ReachDSL-V3 Ports R3.0
ADSL 8965 ATM Card, 24 ADSL Ports R3.0
ADSL 8965 ATM Card, 24 ADSL2 Ports R4.0
ADSL 8966 ATM Card, 48 ADSL Ports R4.0
T1 IMA 8995-B1-000, T1 IMA ATM Card, 8 T1 IMA Ports R3.3
E1 IMA 8997-B1-000, E1 IMA ATM Card, 8 E1 IMA Ports R3.3
SCP 8412-B1-000, SCP card with OC3/STM1 MM ATM uplink R3.0
SCP 8413-B1-000, SCP card with OC3/STM1 SM int ATM uplink R3.0
SCP 8414-B1-000, SCP card with OC3/STM1 SM long ATM uplink R3.0
SCP 8416-B1-000, SCP card with 8 T1 IMA Uplink R3.0
SCP 8417-B1-000, SCP card with 8 E1 IMA Uplink 75 ohm R3.0
SCP 8418-B1-000, SCP card with 8 E1 IMA Uplink 120 ohm R3.0
SCP 8411-B1-000, SCP card with T3 ATM uplink R3.0
SCP 8429-B1-000, SCP card with GigE and 10/100BT R4.0
Wintegra AAAA-B1-0000, IPNP Wintegra Card with GigE and 10/100BT R4.0
1. Network Management Specification
2 June 2004 8000-A2-GB30-30
Table 1-2. Supported RFCs and MIBs (1 of 8)
RFC Name Description
IANAifType-MIB Definitions of IANAifType Textual Convention, and thus the
enumerated values of the ifType objects.
SNMPv2-SMI SNMPv2 definitions
SNMPv2-TC Definitions of textual conventions
ADSL-TC-MIB Definitions for ADSL Line Coding Textual Conventions
N/A Definitions of Supplemental Managed
Objects for ATM Interface.
draft-ietf-atommib-atm2-xx.txt
ATM2-MIB
atmVplLogicalPortEntry
N/A IMA MIB
AF-PHY-0086.001
(http://www.atmforum.com/atmforum/spec
s/approved.html)
The MIB module for managing ATM Forum Inverse Multiplexing
for ATM (IMA) interfaces.
imaGroupNumber,
imaGroupEntry,
imaGroupMappingEntry ,
ImaLinkEntry ,
ImaAlarmType ,
imaGroupCurrentEntry ,
ImaGroupIntervalEntry ,
ImaGroupTotalEntry ,
imaLinkCurrentEntry ,
imaLinkTotalEntry ,
ImaLinkIntervalEntry
N/A SNMP M4 Network Element View MIB
atmfM4MIB
AF-NM-0095.001
(http://www.atmforum.com/atmforum/spec
s/approved.html)
ATM Forum SNMP M4 Network Element View:
atmfM4TcAdapterEntry_t ,
atmfM4AtmLayerEntry_t ,
atmfM4VpNextVpiEntry,
atmfM4VcNextVciEntry,
atmfM4CellProtoCurrEntry_t ,
atmfM4CellProtoHistEntry_t ,
atmfM4TcProtoCurrEntry_t ,
atmfM4TcProtoHistEntry_t ,
atmfM4VcUpcNpcCurrEntry_t ,
atmfM4VcUpcNpcHistEntry_t ,
atmfM4VcTestEntry_t,
atmfM4VclEntry_t
atmfM4VplEntry_t
atmfM4VpXConnEntry_t
atmfM4VcXConnEntry_t
atmfM4VpNextVpiEntry_t
atmfM4VpUpcNpcHistEntry_t
atmfM4VpUpcNpcCurrEntry_t
atmfM4VpTestEntry_t
N/A draft-ietf-snmpv3-coex-v2-02.txt
Coexistence between Version1, Version 2,
and Version 3 of the Internet-standard
Network Management Framework
snmpCommunityEntry_t,
snmpTargetAddrExtEntry_t
1. Network Management Specification
8000-A2-GB30-30 June 2004 3
1493 Defnitions of Managed Objects for Bridges dot1dBaseBridgeAddress
dot1dBaseNumPorts
dot1dBaseType
dot1dBasePortEntry_t
dot1dTpLearnedEntryDiscards
dot1dTpAgingTime
dot1dTpFdbEntry_t
dot1dTpPortEntry_t
dot1dTpPortOverflowEntry_t
1907 SNMPv2-MIB Management Information Base for Version 2 of the Simple
Network Management Protocol (SNMPv2)
2096 IP Forwarding Table Definitions of Managed objects for the Ip Forwading table for
classless inter-domain routing (CIDR):
ipCidrRouteNumber,
ipCidrRouteTable
2493 PerfHist-TC Textual Conventions for MIB Modules Using Performance
History Based on 15 Minute Intervals
2495 Definitions of Managed Objects for the
DS1, E1, DS2 and E2 Interface Types
Definitions of Managed Objects for the DS1, E1, DS2 and E2
Interface Types:
dsx1ConfigEntry_t ,
dsx1CurrentEntry_t ,
dsx1IntervalEntry_t ,
dsx1TotalEntry_t ,
dsx1ChanMappingEntry_t ,
dsx1FarEndCurrentEntry_t,
dsx1FarEndIntervalEntry_t ,
dsx1FarEndTotalEntry_t
2496 Definitions of Managed Objects for the
DS3/E3 Interface Type
dsx3ConfigEntry_t,
dsx3CurrentEntry_t,
dsx3IntervalTable_t,
dsx3TotalEntry_t,
dsx3FarEndConfigEntry_t,
dsx3FarEndCurrentEntry_t,
dsx3FarEndIntervalEntry_t,
dsx3FarEndTotalEntry_t
2514 Definitions of Textual Conventions for
ATM Management
Definitions of Textual Conventions and OBJECT-IDENTITIES
for ATM Management
2515 Definitions of Managed Objects for ATM
Management AToM
ATM MIB (Uses Definitions from 2514)
atmMIBObjects_t,
atmInterfaceConfEntry_t,
atmInterfaceTCEntry_t ,
atmTrafficDescrParamEntry_t ,
atmVclEntry_t ,
atmVcCrossConnectEntry_t,
atmVplEntry_t
atmVpCrossConnectEntry_t
atmVplLogicalPortEntry_t
Table 1-2. Supported RFCs and MIBs (2 of 8)
RFC Name Description
1. Network Management Specification
4 June 2004 8000-A2-GB30-30
2558 Definitions of Managed Objects for the
SONET/SDH Interface Type
sonetMediumEntry_t,
sonetLineCurrentEntry_t,
sonetLineIntervalEntry_t,
sonetSectionCurrentEntry_t,
sonetSectionIntervalEntry_t,
sonetFarEndLineCurrentEntry_t,
sonetFarEndLineIntervalEntry_t,
sonetPathCurrentEntry_t,
sonetPathIntervalEntry,
sonetPathFarEndCurrentEntry_t,
sonetPathFarEndIntervalEntry_t
2662 Definitions of Managed Objects for the
ADSL Lines
Definitions of Managed Objects for the ADSL Lines.
Note: Used for the DMT and Rv3 product line
adslLineEntry_t,
adslAtucPhysEntry_t ,
adslAturPhysEntry_t ,
adslAtucChanEntry_t ,
adslAturChanEntry_t ,
adslAtucPerfDataEntry_t ,
adslAturPerfDataEntry_t ,
adslAtucIntervalEntry_t ,
adslAturIntervalEntry_t ,
adslAtucChanIntervalEntry_t ,
adslAturChanIntervalEntry_t ,
adslLineConfProfileEntry_t,
adslLineAlarmConfProfileEntry_t
2665 Definitions that describes generic objects
for Ethernet-like network interfaces
dot3StatsEntry_t
dot3CollEntry_t
dot3Tests
dot3Errors
dot3ControlEntry_t
2668 Definitions of Managed objects for IEEE
802.3 Medium Attachment Units(MAU).
ifMauEntry_t
ifJackEntry_t
ifMauAutoNegEntry_t
2674q Bridge MIB Extensions dot1qVlanVersionNumber
dot1qMaxVlanId
dot1qMaxSupportedVlans
dot1qNumVlans
dot1qGvrpStatus
dot1qFdbEntry_t
dot1qVlanNumDeletes
dot1qVlanCurrentEntry_t
dot1qVlanStaticEntry_t
dot1qNextFreeLocalVlanIndex
dot1qPortVlanEntry_t
dot1qPortVlanStatisticsEntry_t
dot1ConstraintSetDefault
dot1ConstraintTypeDefault
Table 1-2. Supported RFCs and MIBs (3 of 8)
RFC Name Description
1. Network Management Specification
8000-A2-GB30-30 June 2004 5
2674p Definitions of Managed Objects for
Bridges with Traffic Classes, Multicast
Filtering and Virtual LAN Extensions
dot1dTrafficClassEnabled
dot1dGmrpStatus
dot1dPortCapabilitiesEntry_t
dot1dPortPriorityEntry_t
dot1dUserPriorityEntry_t
dot1dTrafficClassEntry_t
dot1dPortOutboundAccessPriorityEntry_t
dot1dPortGarpEntry_t
dot1dPortGmrpEntry_t
2737 Entity MIB (Version 2) Definitions of Managed Objects for Entity MIB:
entPhysicalEntry_t ,
entLogicalEntry_t ,
entAliasMappingEntry_t ,
entPhysicalContainsEntry_t ,
entityGeneral_t
2863 Evolution of MIB-II Interfaces Evolution of the Interfaces Group of MIB-II:
ifEntry_t,
ifXEntry_t,
ifStackEntry_t
2864 Inverted Stack Extension MIB Definitions of Managed Objects for the Inverted Stack Table
Extension to the Interfaces Group MIB:
ifInvStackEntry_t
2933 Internet Group Management Protocol igmpInterfaceEntry_t
igmpCacheEntry_t
3276 Definitions of Managed Objects for High
Bit-Rate DSL -2nd generation (HDSL2)
and Single-Pair High-Speed Digital
Subscriber Line (SHDSL) Lines
hdsl2ShdslSpanConfEntry_t,
hdsl2ShdslSpanStatusEntry_t,
hdsl2ShdslInventoryEntry_t,
hdsl2ShdslEndpointConfEntry_t,
hdsl2ShdslEndpointCurrEntry_t,
hdsl2Shdsl15MinIntervalEntry_t,
hdsl2Shdsl1DayIntervalEntry_t,
hdsl2ShdslEndpointMaintEntry_t,
hdsl2ShdslUnitMainEntry_t,
hdsl2ShdslSpanConfProfileEntry_t,
hdsl2ShdslEndpointAlarmConfProfileEntry_t
3411_std62 Architecture for SNMP Frameworks snmpEngineID,
snmpEngineBoots,
snmpEngineTime,
snmpEngineMaxMessageSize
3412_std62_a Message Processing and Dispatching for
the Simple Network Management Protocol
snmpUnknownSecurityModels,
snmpInvalidMsgs,
snmpUnknownPDUHandlers
3412_std62_b Identify the layout of the SNMPv3Message Definitions of TAGS
3413_std62_a SNMP Applications (SNMPv3) snmpTargetAddrEntry_t,
snmpTargetParamsTable_t,
snmpUnavailableContexts,
snmpUnknownContexts
3413_std62_b SNMP Notification snmpNotifyEntry_t
Table 1-2. Supported RFCs and MIBs (4 of 8)
RFC Name Description
1. Network Management Specification
6 June 2004 8000-A2-GB30-30
3414_std62_a User-based Security Model (USM) for
version 3 of the Simple Network
Management Protocol (SNMPv3)
Definitions of TAGS
3414_std62_b User-based Security Model (USM) for
version 3 of the Simple Network
Management Protocol (SNMPv3)
usmStats,
usmUserEntry_t
3415_std62 View-based Access Control Model
(VACM) for the version 3 of the Simple
Network Management Protocol (SNMPv3)
vacmContextEntry_t,
vacmSecurityToGroupEntry_t,
vacmAccessEntry_t,
vacmViewTreeFamilyEntry_t,
3433 Definitions of Managed Objects for Entity
Sensor Management Information Base
entPhySensorEntry_t
3440 Definitions of Extention Managed Objects
for Asymmetric Digital Subscriber Lines
Definitions of Extension Managed Objects for ADSL Lines :
adslLineExtEntry_t ,
adslAtucPerfDataExtEntry_t ,
adslAturPerfDataExtEntry_t ,
adslConfProfileExtEntry_t ,
adslAlarmConfProfileExtEntry_t
3498 Definitions of Managed Objects for
SONET Linear APS architectures.
draft-ieft-atommib-sonetaps-mib-xx.txt
apsConfigEntry_t,
apsStatusEntry_t,
apsMapEntry_t,
apsChanConfigEntry_t,
apsCommandEntry_t,
apsChanStatusEntry_t,
apsNotificationEnable
Paradyne Enterprise MIBS
enterprise pdn_tc.mib Paradyne Enterprise Textual Convention
enterprise pdn_Header.mib Paradyne Top-Level Enterprise Definitions
enterprise pdn_syslog.mib Paradyne enterprise syslog mib.
pdnSyslog ,
pdnSyslogEntry
enterprise pdn_SonetExt.mib Paradyne Enterprise Sonet Extension MIB
devSonetConfigEntry_t
enterprise PDN-ENTITY-REDUNDANCY-MIB.mib Paradyne Enterprise Entity Redundancy MIB (Only if
redundancy is supported)
pdnEntityRedundancySelection,
pdnYCableSelection,
pdnRedunGeneralAlarmStatus,
pdnRedunGeneralNotifcationEnable,
pdnRedunCmdEntry,
pdnRedunStatusEntry
enterprise PDN-LINK-FAULT-MGMT-MIB.mib Paradyne Enterprise Link Fault Management MIB (Only if
redundancy is supported)
pdnLinkFaultMgmtApsSelection,
pdnLinkFaultMgmtSwitchoverSelection,
pdnDualLinkSelection
pdnLinkFailureConfigEntry,
Table 1-2. Supported RFCs and MIBs (5 of 8)
RFC Name Description
1. Network Management Specification
8000-A2-GB30-30 June 2004 7
enterprise mpe_Control.mib Paradyne Enterprise Device Control MIB includes the Paradyne
File Transfer Group.
mpeDevFileXferConfigEntry_t ,
mpeDevTestControlEntry ,
mpeDevFirmwareControlEntry_t ,
mpeDevHwControl_t
enterprise mpe_HealthAndStatus.mib Paradyne Enterprise Health and Status MIB
mpeDevHealthAndStatusEntry_t
enterprise pdn_ATMExt.mib
pdn_ATMM4Ext.mib
pdn_ATMStats.mib
Paradyne Enterprise ATM mibs
pdnAtmIfConfExtEntry_t ,
pdnAtmTrafficDescrParamExtEntry_t ,
pdnAtmfM4TcProtoCurrExtEntry_t ,
pdnAtmfM4TcProtoHistExtEntry_t ,
pdnAtmVclHistEntry_t ,
pdnAtmVclCurrEntry_t
pdnAtmVplStatEntry_t
enterprise PDN-MGMT-IP-MIB.mib Paradyne Enterprise Management of IP over ATM interfaces
pdnMgmtIpMib
enterprise pdn_Config.mib Paradyne Enterprise Device Clock Source
devConfigClockSrcEntry_t
devConfigTestTimer
devCurrentClockSrcSelection
devConfigClockSrcAutoSwitchback
enterprise pdn_Security.mib Paradyne enterprise security mib
devSecurityMgrValidation ,
devSecurityMgrMaxNumber ,
devSecurityMgrCurrentNumber ,
securityMgrTable
enterprise pdn_time.mib devTimeAndDate,
devNTP group
enterprise pdn_dslam.mib sysDevUserAccountEntry_t
enterprise pdn_spectrummgmt.mib Paradyne Enterprise spectrum management specific mib.
newSpectrumMgmtGeneralConfigEntry,
newSpectrumMgmtConfEntry,
newSpectrumMgmtLineInfoEntry
enterprise pdn_reachDSL.mib Paradyne Enterprise ReachDSL specific mib.
reachDSLSpectrumMgmtSelection,
reachDSLSpectrumMgmtConfEntry
reachDSLSpectrumMgmtLineInfoEntry,
reachDSLLineEntry,
reachDSLSpectrumMgmtLoopMeasurementMethod,
reachDSLSpectrumMgmtEWLUnits,
reachDSLSpectrumMgmtMod
enterprise PDN-DS1EXT-MIB Paradyne Enterprise supplement for RFC 2495
pdnDs1ExtConfEntry_t
Table 1-2. Supported RFCs and MIBs (6 of 8)
RFC Name Description
1. Network Management Specification
8 June 2004 8000-A2-GB30-30
enterprise mpe_dslam mpeEntExtAlarms_t
mpeEntPhysicalEntEntry_t
enterprise pdn_Ds3Ext.mib Paradyne Enterprise supplement for RFC 2496
devDs3ConfigEntry_t
enterprise
PDN-MPD-EXT-MIB.mib Paradyne Enterprise Message Processing Dispatcher
pdnMpdExtSecurityModeConfig
enterprise
PDN-SFP-MIB.mib Paradyne Enterprise for managing Small Form-Factor
Pluggable (SFP) Transceivers.
sfpCompatibleInterfaceCount
sfpInfoEntry_t
sfpCommandEntry_t
enterprise
pdn_ether.mib Paradyne Enterprise for managing ethernet interfaces
pdnPortConfigMauExtEntry_t
pdnIfJackTable
enterprise
pdn_TrapMgr.mib Paradyne Enterprise for configuring trap options
pdnDevConfigTrapsEnable
enterprise
PDN-ENTITY-SENSOR-EXT-MIB Paradyne Supplement to the ENTITY-SENSOR-MIB
(RFC 3433)
pdnEntPhySensorExtEntry_t
enterprise
PDN-ATM-BRIDGE-IWF-MIB Paradyne Enterprise Bridge-ATM Interworking Function
pdnAtmBridgeIwfEntry_t
enterprise
PDN-DOT1QEXT-MIB.mib Paradyne Supplement to the Bridge MIB
pdnDot1qVlanStatcExtEntry_t
pdnDot1BasePortPIWGEntry_t
pdnDot1TpFdbClear
enterprise
PDN-IGMP-STD-EXT-MIB.mib Paradyne Supplement to the IGMP-STD-MIB
pdnIgmpInterfaceExtEntry_t
pdnIgmpCacheExtEntry_t
pdnIgmpSnoopingSelection
enterprise
PDN-IP-MULTICAST-MIB.mib Paradyne Enterprise IGMP and IP multicast mib
pdnIgmpProxyEnableDisable
pdnIgmpProxyReportSummaryEnableDisable
enterprise
PDN-UPLINK-TAGGING-MIB.mib Paradyne Enterprise Uplink Tagging mib
pdnUltIndex
pdnGenUltBaseVlanTag
pdn48UltBaseVlanTag
pdn24UltBaseVlanTag
enterprise
PDN-VLAN-MIB.mib Paradyne Enterprise Supplement to VLAN mibs
pdnVlanInbandMgmtVlanId
pdnVlanInbandMgmtVlanId2
Table 1-2. Supported RFCs and MIBs (7 of 8)
RFC Name Description
1. Network Management Specification
8000-A2-GB30-30 June 2004 9
enterprise
pdn_IfExtConfig.mib Paradyne Enterprise Interface Config mibs
pdnIfXLinkConfigEntry_t
Table 1-3. Other Supported RFCs Used as Guidelines for Implementation
RFC Name/Description
768 User Datagram Protocol
791 Internet Protocol
792, 950 Internet Control Message Protocol; Internet Standard Subnetting Procedure
793 Transmission Control Protocol
826 Ethernet Address Resolution Protocol: Or converting network protocol addresses to 48.bit Ethernet
address for transmission on Ethernet hardware
854 Telnet Protocol Specification
894 A Standard for the Transmission of IP Datagrams over Ethernet Networks
959 File Transfer Protocol
1042 Transmission of IP datagrams over IEEE 802.3 networks
1122 Requirements for Internet Hosts Communication Layers
1123 Requirements for Internet Hosts Application and Support
1157 Simple Network Management Protocol (SNMP) SNMP version 1
1483, 2684 Multiprotocol Encapsulation over ATM Adaptation Layer 5
1659 Definitions of Managed Objects for RS-232-like Hardware Devices using SMIv2
1769 Simple Network Time Protocol (SNTP)
2131, 2132 Dynamic Host Configuration; Protocol , DHCP Options and BOOTP Vendor Extensions
2493 Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals
2570 Introduction to Version 3 of the Internet-standard Network Management Framework.
3164 The BSD Syslog Protocol
Table 1-2. Supported RFCs and MIBs (8 of 8)
RFC Name Description
1. Network Management Specification
10 June 2004 8000-A2-GB30-30
2. Standards Compliance for SNMP Traps
This section describes the standards compliance and any special operational
features/options for the SNMP Traps supported by the BAC products. The following traps
are supported.
Table 1-4. Summary of Traps (1 of 7)
Trap Description VarBind(s)
Standard Traps
LinkDown Signifies that the unit has recognized a
failure in one of the communication
interfaces.
ifIndex(RFC 2863)
ifAdminStatus(RFC 2863)
ifOperStatus(RFC 2863)
devLastTrapString
LinkUp Signifies that the unit recognized that one
of the communication interfaces has come
up.
ifIndex(RFC 2863)
ifAdminStatus(RFC 2863)
ifOperStatus(RFC 2863)
devLastTrapString
WarmStart Signifies that the SNMPv2 entity, acting
in an agent role, is reinitializing itself such
that its configuration is unaltered.
devLastTrapString
AuthenticationFailureTrap Signifies that the SNMPv2 entity, acting
in an agent role, has received a protocol
message that is not properly
authenticated. While all implementations
of the SNMPv2 must be capable of
generating this trap, the
snmpEnableAuthenTraps object indicates
whether this trap will be generated.
devLastTrapString
DSX Traps
dsx1LineStatusChange value of an instance dsx1LineStatus
changes
ifIndex,
dsx1LineStatus,
dsx1LineStatusLastChange
devLastTrapString
dsx3LineStatusChange value of an instance dsx3LineStatus
changes
ifIndex,
dsx3LineStatus,
dsx3LineStatusLastChange
devLastTrapString
ATM-M4 Traps
atmfM4IfAisAlarm AIS condition has occurred. ifIndex,
ifOperStatus,
atmfM4TrapAlarmSeverity
devLastTrapString
atmfM4IfLcdAlarm LCD (Loss of Cell Delineation) condition
has occurred.
atmfM4IfLosAlarm LOS (Loss of Signal) condition has
occurred.
atmfM4IfLofAlarm LOF (Loss of Frame) condition has
occurred.
ifIndex,
ifOperStatus,
atmfM4TrapAlarmSeverity
devLastTrapString
1. Network Management Specification
8000-A2-GB30-30 June 2004 11
atmfM4VclXConnCreated Indicates that the VCL cross-connection
has just been created. When a
cross-connection is created along with its
VCL endpoints, this trap should be
emitted to indicate the creation of the
entire group of objects.
atmVcCrossConnectL2HOperStatus,
atmVcCrossConnectH2LOperStatus,
devLastTrapString
atmfM4VclXConnDeleted Indicates that the VCL cross-connection
has just been created. When a
cross-connection is created along with its
VCL endpoints, this trap should be
emitted to indicate the creation of the
entire group of objects.
atmfM4VclXConnChanged Indicates that the VCL cross-connection
configuration has been changed.
atmfM4VplXConnCreated Indicates that the VPL cross-connection
has just been created. When a
cross-connection is created along with its
VPL endpoints, this trap should be
emitted to indicate the creation of the
entire group of objects.
atmVcCrossConnectL2HOperStatus,
atmVcCrossConnectH2LOperStatus,
devLastTrapString
atmfM4VplXConnDeleted Indicates that the VPL cross-connection
has just been created. When a
cross-connection is created along with its
VPL endpoints, this trap should be
emitted to indicate the creation of the
entire group of objects.
atmfM4VplXConnChanged Indicates that the VPL cross-connection
configuration has been changed.
atmfM4HwFanFailAlarm This trap is generated when a cooling fan
failure condition has occurred on the
hardware unit associated.
entPhysicalIndex,
ifOperStatus,
atmfM4TrapAlarmSeverity
devLastTrapString
atmfM4AtmCellIfCreated This trap is generated when an ATM
SubInterface is created.
ifOperStatus,
atmfM4IfType
atmfM4AtmCellIfDeleted This trap is generated when an ATM
SubInterface is removed.
ifOperStatus
Entity MIB Traps:
entConfigChange This trap is generated when the value of
entLastChangeTime changes. It can be
utilized by a NMS to trigger
logical/physical entity table maintenance
polls.
devLastTrapString
mpeEntPhysicalExtEntityCreated This trap signifies that an instance of this
entity has been created from the
entPhysicalTable.
devLastTrapString
Table 1-4. Summary of Traps (2 of 7)
Trap Description VarBind(s)
1. Network Management Specification
12 June 2004 8000-A2-GB30-30
mpeEntPhysicalExtEntityDeleted This trap signifies that an instance of this
entity has been deleted from the
entPhysicalTable.
devLastTrapString
mpeEntPhysicalExtEntityChanged This trap signifies that an instance of this
entity has been changed from the
entPhysicalTable.
devLastTrapString
SHDSL MIB Traps:
hdsl2ShdslLoopAttenCrossing This notification indicates that the loop
attenuation threshold has been
reached/exceeded for the HDSL2/SHDSL
segment endpoint.
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAtten
uation
devLastTrapString
hdsl2ShdslSNRMarginCrossing This notification indicates that the SNR
margin threshold has been
reached/exceeded for the HDSL2/SHDSL
segment endpoint.
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMarg
in
devLastTrapString
hdsl2ShdslPerfESThresh This notification indicates that the errored
seconds threshold has been
reached/exceeded for the HDSL2/SHDSL
segment endpoint.
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointThreshES
devLastTrapString
hdsl2ShdslPerfSESThresh This notification indicates that the
severely errored seconds threshold has
been reached/exceeded for the
HDSL2/SHDSL segment endpoint.
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointThreshSES,
devLastTrapString
hdsl2ShdslPerfCRCanomaliesThresh This notification indicates that the CRC
anomalies threshold has been
reached/exceeded for the HDSL2/SHDSL
segment endpoint.
hdsl2ShdslEndpointCurr15MinCRCa
nomalies,
hdsl2ShdslEndpointThreshCRCanom
alies
devLastTrapString
hdsl2ShdslPerfLOSWSThresh This notification indicates that the LOSW
seconds threshold has been
reached/exceeded for the HDSL2/SHDSL
segment endpoint.
hdsl2ShdslEndpointCurr15MinLOS
WS,
hdsl2ShdslEndpointThreshLOSWS,
devLastTrapString
hdsl2ShdslPerfUASThresh This notification indicates that the
unavailable seconds threshold has been
reached/exceeded for the HDSL2/SHDSL
segment endpoint.
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS,
devLastTrapString
hdsl2ShdslSpanInvalidNumRepeaters This notification indicates that a
mismatch has been detected between the
number of repeater/regenerator units
configuredfor a HDSL2/SHDSL line via
the hdsl2ShdslSpanConfNumRepeaters
object and the actual number of
repeater/regenerator units discovered via
the EOC.
hdsl2ShdslSpanConfNumRepeaters,
devLastTrapString
hdsl2ShdslLoopbackFailure This notification indicates that an
endpoint maintenance loopback command
failed for an HDSL2/SHDSL segment.
hdsl2ShdslMaintLoopbackConfig,
devLastTrapString
Table 1-4. Summary of Traps (3 of 7)
Trap Description VarBind(s)
1. Network Management Specification
8000-A2-GB30-30 June 2004 13
hdsl2ShdslpowerBackoff This notification indicates that the bit
setting for powerBackoff in the
hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed.
hdsl2ShdslEndpointCurrStatus,
devLastTrapString
hdsl2ShdsldeviceFault This notification indicates that the bit
setting for deviceFault in the
hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed.
hdsl2ShdslEndpointCurrStatus,
devLastTrapString
hdsl2ShdsldcContinuityFault This notification indicates that the bit
setting for dcContinuityFault in the
hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed.
hdsl2ShdslEndpointCurrStatus,
devLastTrapString
hdsl2ShdslconfigInitFailure This notification indicates that the bit
setting for configInitFailure in the
hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed.
hdsl2ShdslEndpointCurrStatus,
devLastTrapString
hdsl2ShdslprotocolInitFailure This notification indicates that the bit
setting forprotocolInitFailure in the
hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed.
hdsl2ShdslEndpointCurrStatus,
devLastTrapString
hdsl2ShdslnoNeighborPresent This notification indicates that the bit
setting for noNeighborPresent in the
hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed.
hdsl2ShdslEndpointCurrStatus,
devLastTrapString
hdsl2ShdslLocalPowerLoss This notification indicates timpending
unit failure due to loss of local power (last
gasp).
hdsl2ShdslInvVendorID,
devLastTrapString
Enterprise Specific Traps:
mpeSelfTestFailure A hardware failure of the unit was
detected as part of the unit’s selftest. This
trap will be generated after the unit has
completed initialization
entPhysicalIndex,
mpedevSelfTestResults,
devLastTrapString
mpeCcn This trap is generated to indicate a change
in the configuration in the entity unit
specified by the entPhysicalIndex value.
entPhysicalIndex,
devLastTrapString
devSonetStatusChange A devSonetStatusChange trap is sent
when the value of an instance of
sonetSectionCurrentStatus or
sonetLineCurrentStatus or
sonetPathCurrentStatus changes.
devSonetStatusLastChange,
sonetSectionCurrentStatus,
sonetLineCurrentStatus,
sonetPathCurrentStatus,
devLastTrapString
pdnRedunEventNoActiveModule This notification will be issued when no
module is the Active State.
pdnRedunGeneralAlarmStatus,
devLastTrapString
pdnRedunEventHwIncompatible This notification will be issued when the
modules in a redundancy configuration
present hardware incompatibilities.
pdnRedunAlarmStatus,
devLastTrapString
Table 1-4. Summary of Traps (4 of 7)
Trap Description VarBind(s)
1. Network Management Specification
14 June 2004 8000-A2-GB30-30
pdnRedunEventStandbyAlarmOrReset This notification will be issued when one
of the modules configured for redundancy
is either in the Standby/Alarm or Reset
Test state.
pdnRedunGeneralAlarmStatus,
devLastTrapString
pdnRedunEventFwIncompatible This notification will be issued when the
modules in a redundancy configuration
present firmware incompatibilities.
pdnRedunAlarmStatus,
devLastTrapString
pdnRedunEventCfgIncompatible This notification will be issued when the
modules in a redundancy configuration
present configuration incompatibilities.
pdnRedunAlarmStatus,
devLastTrapString
pdnRedunEventLinkDefect This notification will be issued when one
of the modules in a redundancy
configuration has a link failure condition
pdnRedunAlarmStatus,
devLastTrapString
pdnRedunEventHwDefect This notification will be issued when one
of the modules in a redundancy
configuration has a hardware failure
condition
pdnRedunAlarmStatus,
devLastTrapString
pdnRedunEventHwMissingHwFailure This notification will be issued when one
of the modules in a redundancy
configuration is expecting a piece of hw
which can not be found.
pdnRedunAlarmStatus,
devLastTrapString
sfpEventFaulty This notification will be issued when the
sfp associated with a physical port is
detected as being faulty.
sfpStatusCurrent
devLastTrapString
sfpEventOperational This notification will be issued when the
sfp associated with a physical port is
detected as being working.
sfpStatusCurrent
devLastTrapString
sfpEventInserted This notification will be issued when the
sfp is inserted into a physical port.
sfpStatusCurrent
devLastTrapString
sfpEventRemoved This notification will be issued when the
sfp is removed from a physical port..
sfpStatusCurrent
devLastTrapString
ADSL Specific Traps:
adslAtucPerfLofsThreshTrap Loss of Framing 15-minute interval
threshold reached
ifIndex,
dslAturPerfCurr15MinLofs,
adslAturThresh15MinLofs,
devLastTrapString
adslAtucPerfLossThreshTrap Loss of Signal 15-minute interval
threshold reached
ifIndex,
adslAtucPerfCurr15MinLoss,
adslAtucThresh15MinLoss,
devLastTrapString
adslAtucPerfESsThreshTrap Errored Second 15-minute interval
threshold reached
ifIndex,
adslAtucPerfCurr15MinESs,
adslAtucThresh15MinESs,
devLastTrapString
Table 1-4. Summary of Traps (5 of 7)
Trap Description VarBind(s)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128

Paradyne 8820 Reference guide

Category
Networking
Type
Reference guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI