Page is loading ...
ITEM #0161014
BLACK FIREPLACE HOOD
Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-866-573-0674, 8:00 a.m - 4:30 p.m., EST,
Monday - Friday or e-mail [email protected].
MODEL # BFH1
LS-BFH1- 1003
Español p. 12
2
HARDWARE CONTENTS
Picture
Part Description Quantity (Shown to size)
AA
BB
4
4
Metal Screws
Masonry Screws
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list. If any part is missing or damaged, do not attempt to assemble the
product. Contact customer service for replacement parts.
Estimated Assembly Time: 1 hour
Tools Required for Assembly: Philips Screwdriver, Tape Measure, Adhesive Tape, Pencil or
Marker and Metal Cutting Saw.
WARNINGS AND CAUTIONS
WARNING:
Fireplace hood becomes very hot during replace operation. Do not touch replace hood. Severe
burns could occur.
PACKAGE CONTENTS
Part Description Quantity
A Fireplace Hood Assembly
B Fireplace Hood (Left) 1
C Fireplace Hood (Middle) 1
D Fireplace Hood (Right) 1
E Mounting Bracket 2
B
E
C
D
A
3
SIZING THE FIREPLACE HOOD TO THE FIREPLACE
OPENING OR GLASS DOOR FRAME
The replace hood assembly is adjustable from 28 to 48
in. You must open hood assembly wide enough to cover
the entire replace opening. You can open hood wider if
desired. For best appearance, make sure center section of
hood assembly is centered with the replace opening.
Follow the instructions below to properly size the
replace hood assembly.
1. Measure width of replace opening or glass door frame
(see Measurement ”A”, Fig. 1). Use work space below
to gure proper size for replace hood.
Measurement ”A”_____________________________
Subtract 24 in.
(width or hood center section)___________________
Subtotal =___________________________________
Divided by 2_________________________________
Measurement ”B”=____________________________
Measurement ”B” is the distance from the outside edges
of center-hood assembly section to outside edges of
adjustable outer-hood assembly sections (see Fig. 2).
When adjustable outer sections are extended to this
measurement, hood assembly will be correct size. The
overall width of the hood assembly will equal the width of
the replace opening. If you have glass doors and would
like the hood assembly to hang beyond the edge of the door
frame, add 1/2 in. to measurement “B”. Make sure that hood
provides room for opening doors.
Fig. 1
Fig. 2
2. Place center-hood section face down on a smooth,
soft surface.
ASSEMBLY INSTRUCTIONS
Measurement ”A”
Fireplace Opening
Measurement ”A”
Glass Door Frame
Measurement ”B”
Adjustable Outer-Hood
Sections
Center-Hood
Section
4
3. Measure in from outside ends of adjustable
outer-hood sections. Place a piece of tape on
bent-under ange of adjustable outer-hood
sections to mark the distance of Measurement
”B” (see Fig. 3).
4. Slide the adjustable outer-hood sections into
center section. Stop when edge of center-hood
section is even with tape (see Fig. 4).
Place pieces of tape across adjustable
outer-hood sections and center-hood section to
hold in place.
IMPORTANT: You must remove tape before
operating your replace.
Fig. 3
Fig. 4
Tape
Adjustable Outer-
Hood Sections
Measurement ”B”
Edge of Center-
Hood Section
5
INSTALLING HOOD TO MASONRY
FIREPLACE
Follow the instructions below that best describes
your replace.
Masonry With Glass Doors
5. Loosen clamps that hold glass door frame to
replace. Slide the mounting brackets (E) behind
the glass door frame (see Fig. 5). Place mounting
brackets near ends of horizontal glass door frame.
6. Note: If frame is too tall, the bottom of mounting
bracket will not slide under lintel (top) of replace. If
so, cut mounting bracket off at point ”Y” (see Fig. 6).
7. Slide mounting bracket (E) into glass door frame
(see Fig. 7). Tighten glass door lintel clamps. This
will secure the mounting brackets.
8. Slide the replace hood assembly (A) over the
mounting brackets (E) see Fig. 8.
Fig. 5
Fig. 6
Fig. 7
Fig. 8
E
Bottom of
Mounting
Bracket
E
Glass
Door
Frame
6
Fig. 9 Masonry Without Glass Doors
9. Tape the mounting brackets (E) near the ends
of the replace opening. Make sure to
position mounting brackets (E) as shown in
Fig. 9. Mark screw locations on replace lintel
through the slots on bottom of each mounting
brackets (E) as shown in Fig. 9.
Remove mounting brackets (E) and drill a 5/32 in.
diameter hole into replace lintel at each marked
location.
Use the masonry screws (BB) provided to fasten
brackets to Lintel (see Fig. 9).
10. Slide replace hood assembly (A) over
mounting brackets (E) see Fig.10.
Hardware Used
BB
x 4
Masonry Screws
BB
E
Lintel
Fig. 10
E
A
BB
Lintel
7
INSTALLING HOOD TO MANUFACTURED
FIREPLACE
WARNING: Many manufactured replaces
have louver openings for ventilation. Do not
cover any louver openings with replace hood.
Do not mount replace hood above any louver
openings. Only mount replace hood below
louver openings. Covering louver openings or
mounting replace hood above louver openings
will cause the replace to overheat and
could cause property damage, personal injury,
or death due to re.
You may need to alter or discard the mounting
brackets to install the replace hood to the
manufactured replace.
Installing Above Manufactured Fireplace
Opening
Cut mounting bracket off at point ”X” (see
Fig. 6, page 5).
11. Tape mounting bracket (E) to replace
housing. Make sure top of mounting bracket is six
inches above replace opening (see Fig. 11).
Make screw locations through slots in mounting
bracket (E).
Remove mounting bracket (E) and drill a 1/8
in. diameter hole into replace housing at each
marked location.
Use the metal screws (AA) provided to fasten
brackets to replace housing (see Fig. 11).
Slide replace hood assembly (A) over mounting
brackets (E) see Fig.11.
Fig. 11
Hardware Used
AA
x 4
Metal Screws
E
6
in.
AA
Manufactured
Fireplace
Fireplace Opening
A
Manufactured
Fireplace
Fireplace Opening
8
Installing Into Manufactured Fireplace Opening
Discard the mounting brackets.
12. Place the replace hood assembly (A) inside
the replace opening (see Fig. 12)
13. Hold the replace hood assembly (A) in place
and drill four holes through hood and into channel
on the replace opening (see Fig. 13). Make sure
holes are evenly spaced and cover most of the
hood’s length.
Use the sheet metal screws provided to fasten
the replace hood assembly (A) to the replace
opening.
Fig. 12
A
Fig. 13
IMPORTANT: Remove all tape used when
installing replace hood assembly (A) before
operating replace.
Fireplace
Opening
Fireplace
A
Manufactured
Fireplace
Fireplace
Opening
Manufactured Fireplace
Fireplace
Opening
Fireplace
Opening
Fireplace
Hood
Manufactured
Fireplace
Fireplace
Cross
Section
Approximate Screw
Locations
9
REPLACEMENT PARTS
NOTE: Use only original replacement parts. This will protect your warranty coverage for parts
replaced under warranty.
PARTS UNDER WARRANTY
Call Customer Service toll free at (1-866-573-0674) for referral information.
When calling Customer Service, have ready:
• Your name
• Your address
• Model and serial number of your heater
• How heater was malfunctioning
• Type of gas used (Propane/LP or Natural gas/NG)
• Purchase date
• Usually, we will ask you to return the defective part to the factory
PARTS NOT UNDER WARRANTY
Call Customer Service toll free at (1-866-573-0674) for referral information.
When calling Customer Service have ready:
• Model number of your heater
• The replacement part number
10
Part Description Part # Quantity
A Fireplace Hood Assembly
B Fireplace Hood (Left) BFH1-03 1
C Fireplace Hood (Middle) BFH1-01 1
D Fireplace Hood (Right) BFH1-02 1
E Mounting Bracket BFH1-04 2
B
E
C
D
A
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at
1-866-573-0674,
8:00 a.m - 4:30 p.m., EST, Monday - Friday or e-mail [email protected].
11
2-YEAR LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in workmanship and material
present at time of shipment from the factory for two (2) years from the date of purchase. This
warranty applies only to the original purchaser. The manufacturer agrees to correct such
defect at no charge or, at our option, replace the product with a comparable or superior model.
To obtain warranty service, call our customer service department at 1-866-573-0674. You
may be required to present a copy of your sales receipt as proof of purchase. All costs of
removal and reinstallation are the expressed responsibility of the purchaser. Any damage to
the product by accident, misuse, improper installation, or by afxing accessories not produced
by the manufacturer, are the purchaser’s responsibility. The manufacturer assumes no
responsibility whatsoever for installation during the warranty period.
There is no further expressed warranty. The manufacturer disclaims any and all implied
warranties. The manufacturer shall not be liable for incidental, consequential, or special
damages arising at or in connection with product use or performance except as may
otherwise be accorded by law. This warranty gives you specic legal rights, and you also have
other rights which vary from state to state. This warranty supersedes all prior warranties.
Printed in China
/
