Roland MDS-Standard2 Owner's manual

MDS-Standard2
Roland
Brand
Roland
Model
MDS-Standard2
Type
Owner's manual

This manual is also suitable for

NOTE
• Whensetting-uporadjustingthestand,takecarenottopinchyourngersbetweenmovablepartsandthemainunit.Ifusingthisinalocationwherechildrenarepresent,besuretoprovideadultsupervisionorguidance.
• Prepareanareainwhichyoucanperformtheassemblysafely.
• Donotuseapowertool(e.g.,anelectricscrewdriver)toassemblethestand.Youriskdamagingorstrippingthescrews.
• Whenremovingthepartsfromthepackingcarton,takecarethatyourboxcutterorothersharpimplementdoesnotscratchthepipes.
• Ifyouwillbeusingthisdrumstandforanextendedperiodoftimeinthesamelocation,werecommendthatyouuseadrummat(TDMseries)madebyRolandtopreventtherubberfeetfromsoilingthesurfaceonwhichtheyareplaced.
Beforeusingthisunit,carefullyread“USINGTHEUNITSAFELY”and“IMPORTANTNOTES.”Afterreading,keepthedocument(s)
whereitwillbeavailableforimmediatereference.
Roland,V-DrumsareeitherregisteredtrademarksortrademarksofRolandCorporationintheUnitedStatesand/orothercountries.
Owner’s Manual
©2019RolandCorporation
How to Set Up the Stand
1.
Check the parts
Beforeyoustartassemblingthestand,makesurethat
youhavealloftheparts.
1
2
3
4
5 6
7
8
10
9
11
12
13
Number Name Quantity
1 StraightpipeL(Long) 1
2
CurvedpipeL
(withonepadmount,withonememorylock)
1
3 Centerpipe(upper)(withtwopadmounts) 1
4 Centerpipe(lower) 1
5 MainunitpipeL(secondholderhigher) 1
6 MainunitpipeR(secondholderlower) 1
7
CurvedpipeR
(withtwopadmounts,withonememorylock)
1
8 StraightpipeR(Short) 1
9 Cymbalmount 3
10 Padmount 3
11 Cableclip 4
12 Drumkey 1
13 Cabletie 4
2.
Assembling the center section
2–1. Attachthecenterpipes(upper
3
/lower
4
)tothe
mainunitpipeL
5
.
• Insertthecenterpipe(upper)
3
intothetop
holderofthemainunitpipeL
5
.
• Insertthecenterpipe(lower)
4
intothethird
holderfromthetop.
Center pipe (upper)
3
Main unit pipe L
5
Center pipe (lower)
4
Aligntheguideholewiththegapoftheholder,
andtighten(twolocations)usingthedrumkey
12
.
2–2. AttachthemainpipeR
6
.
• Insertthecenterpipe(upper)
3
intothetop
holderofthemainunitpipeR
6
.
• Insertthecenterpipe(lower)
4
intothe
secondholder.
Center pipe (upper)
3
Main unit pipe R
6
Center pipe (lower)
4
Aligntheguideholewiththegapoftheholder,
andtighten(twolocations)usingthedrumkey
12
.
3.
Attaching the left arm section
3–1. Positionthesecondholderfromthetopofthemain
unitpipeL
5
facingoutward,andinsertthecurved
pipeL
2
.
Curved pipe L
2
Main unit pipe L
5
Aligntheguideholewiththegapoftheholder,
andtightenusingthedrumkey
12
.
3–2. Alignthememorylockwiththeholder,andtighten
usingthedrumkey
12
.
Alignpositions
Memory lock
3–3. AttachthestraightpipeL
1
.
Aligntheguideholewiththegapoftheholder,
andtightenusingthedrumkey
12
.
Straight pipe L
1
4.
Attaching the right arm section
4–1. PositionthebottomholderofthemainunitpipeR
6
facingoutward,andinsertcurvedpipeR
7
.
Curved pipe R
7
Main unit pipe R
6
Aligntheguideholewiththegapoftheholder,
andtightenusingthedrumkey
12
.
4–2. Alignthememorylockwiththeholder,andtighten
usingthedrumkey
12
.
4–3. AttachthestraightpipeR
8
.
Aligntheguideholewiththegapoftheholder,
andtightenusingthedrumkey
12
.
Straight pipe R
8
4–4. Verifythatthefourverticalpipesaretrulyvertical.
Ifthestandwobbleswhenplacedontheoor,
loosentheholdersandmakeadjustments.
5.
Assembling the cymbal mount
5–1. Loosenthehandknobandpullouttherod.
Hand knob
Joint
Rod
5–2. Rotatethejointandinserttherod.
Joint
5–3. Tightenthehandknob.
6.
Attaching the pad mounts and cymbal mounts
Pad mounts
10
Cymbal mounts
9
6–1. Raisethemountholders(threelocations)ofthe
centerpipe(upper)
3
andthecurvepipeR
7
.
Mount holders
6–2. Attachpadmounts
10
totheholdersthatyouraised,
andtightenusingthehandknobs(threelocations).
Hand knobs
6–3. Attachthecymbalmounts
9
inthepositionsshown
intheillustration,andtightenusingthehandknobs
(threelocations).
Notes
• Whensettinguporstoringthestand,becarefulnot
topinchthengersyouusetohandlethestand.
• Regardingthewayofmountingadrumsound
module,pads,orcymbals,pleaserefertothesetup
guideofyourdrumkit.
Aligning the position of pipes and holders
Align the guide hole with the gap of the holder
Rotatetheinserted
pipe,adjustingitso
thattheguideholeis
visiblethroughthegap
oftheholder.
Guide hole
Gap
Rotate pipe to adjust
Usethecableclips
11
andcableties
13
tomanagethecables
neatlywhenattachingthepadsandthesoundmodule.
Whensettingup,payattentiontosafetysothatthestanddoesnotfallover.
Refertothesetupguideofyourdrumkit,andobservethesafetyprecautionswhensettingup.
Assembly for a Left-Handed Player
Forleft-handeduse,assemblethestandwithleftandrightreversedasshownintheillustration.
• Beforeyoubeginwork,loosenthememorylocksofcurvedpipesL
2
andR
7
.Whenyounishassembly,
adjustthepositionandretighten.
• Forthepositionatwhichtoattacheachmount,refertothesetupguideofyourdrumkit.
Straight pipe L
1
Center pipe (upper)
3
Center pipe (lower)
4
Main unit pipe L
5
Straight pipe R
8
Pad mount
10
Main unit pipe R
6
Cymbal mount
9
Memory lock
Curved pipe L
2
Curved pipe R
7
Aligning the position of pipes and holders
1. Turn the inserted pipe to align the guide hole with
the holder notch (the mark at which to align the
memory lock), and push it all the way in.
Holdernotch
Guidehole
Adjusting the memory lock
1. Use the drum key
12
to loosen the screw of the
memory lock.
2. Rotate the memory lock 180 degrees, and align
the holder notch with the memory lock mark.
Alignpositions
Memorylock
3. Use the drum key
12
to securely tighten the
memory lock screw.
2
English
  • Page 1 1

Roland MDS-Standard2 Owner's manual

MDS-Standard2
Roland
Brand
Roland
Model
MDS-Standard2
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents