DVH15423X
DVH1538X
EN INSTRUCTION MANUAL
Reviewing the section on troubleshooting Tips will help
you solve some common problems by yourself.
Dea r Cu stomer,
Please carefully read th is manual before using the
dishwa sher, it will help you use and mainta in the
dishwa sher properly.
Pass i t on to any subseq uent owner of the appliance.
This manual contains se ctions on safety Instructions,
Operating Instructio ns, Inst allat ion Instructions and
Troubleshooting Tip s, etc.
The man ufacture r, following a policy of constant
dev elopment and updating of the product, may
make modifications w ithout giving prior notice.
If lost or out-of-d ate, you can receive a new user
manual from the manufacturer or responsible
vendor.
Keep this man ual for future reference.
If you cannot solve the problems by yourself,
please ask for help from a professional technician.
Dishwasher Features.................................... ........6
A Water So ftener..................... .... ..... ........ ......... .7、
...... ............................. ............... 12
Rec ommendations for loading and unl oading
the dishwasher
Filter System.......................................................16
Caring for the Dishwasher..................... ..............17.
B Loading th e Salt into the Softener......................8、
C Filling the Rinse Aid Dispenser......................... 8、
D Function of Detergent ......................................9、
Loading the upper ....................................13Basket
Loading the Lower ....................................13Basket
Wash Cycle Table.............. ..................................14
Turning on the Appliance.....................................14
... ......... ..............15
Changing the Program m id-cyc le
At the en d o f th e Wash Cycle................. ...............15
Before calling for service................. .......... ... .......25.
Error codes.................................... ...................26.
Technical information.............................. ..........27..
Control Panel........................................................6
Installation preparation. ................................. .....18
........19Aesthetic panel's dimensions and installation
Tension adjustment of the door spring ...................21
Connection of drain hoses.............................. .....21
Dishwasher installation steps......................... .....22
About Electricity Con nec ting................................23
Cold Water Conne ction.................... .............. .....24
1
This appliance is intended to be used in household
and similar applications such as:
-staff kitchen areas in shops, offices and other
working environments;
-farm houses;
-by clients in hotels, motels and other residential type
environments;
-bed and breakfast type environments.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be done by children
without supervision.(For EN60335-1)
Packaging material could be dangerous for children!
This appliance is for indoor household use only.
To protect against the risk of electrical shock,
do not immerse the unit, cord or plug in water or
other liquid.
Please unplug before cleaning and performing
maintenance on the appliance.
Use a soft cloth moistened with mild soap, and then
use a dry cloth to wipe it again.
When using your dishwasher,
follow the precautions listed below:
2
This appliance must be earthed. In the event of a
malfunction or breakdown, earthing will reduce the
risk of an electric shock by providing a path of least
resistance of electric current. This appliance is
equipped with an earthing conductor plug.
The plug must be plugged into an appropriate outlet
that is installed and earthed in accordance with all
local codes and ordinances.
Improper connection of the equipment-earthing
conductor can result in the risk of an electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded.
Do not modify the plug provided with the appliance;
If it does not fit the outlet.
Have a proper outlet installed by a qualified electrician.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not operate your dishwasher unless all enclosure
panels are properly in place.
Open the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects on or stand on the door
when it is open. The appliance could tip forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely to
damage the door seal;
3
2) Warning: Knives and other utensils with sharp points
must be loaded in the basket with their points
down or placed in a horizontal position.
Check that the detergent powder is empty after
completion of the wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent.
For check the
manufacturer's recommendations.
Use only detergent and rinse agents recommended for
use in an automatic dishwasher.
The door should not be left open, since this could increase
the risk of tripping.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
During installation, the power supply must not be
excessively or dangerously bent or flattened.
Do not tamper with controls.
The maximum number of place settings to be washed
is 15.
The maximum permissible inlet water pressure is 1MPa.
The minimum permissible inlet water pressure is 0.04MPa.
facing
“ ”
unmarked plastic items not so marked,
Never use soap, laundry detergent, or hand washing
detergent in your dishwasher.
The appliance needs to be connected to the main water
valve using new hose sets. Old sets should not be reused.
4
This appliance's packaging materials are recyclable.
Dispose of the packaging into a suitable waste
collection container to recycle it.
It is prohibited to dispose of this appliance as
household waste.
Correct Disposal of this product: this symbol on the
product or in its packing indicates that this product
may not be treated as household waste. Instead,
it should be taken to the appropriate waste collection
point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative
consequences for the environment and human health,
which could otherwise be caused by the inappropriate
waste handling of this product.
For more detailed information about the recycling of
this product, please contact your local council your
household waste disposal service, or the shop where
you purchased the product.
For disposing of package and the appliance please
go to a recycling centre. Therefore cut off the power
supply cable and make the door closing device
unusable.
Cardboard packaging is manufactured from recycled
paper and should be disposed in the waste paper
collection for recycling.
By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences
for the environment and human health, which could
otherwise be caused by inappropriate waste handling
of this product.
For more detailed information about recycling of this
product, please contact your local city office and your
household waste disposal service.
DISPOSAL: Do not dispose this product as unsorted
municipal waste. Collection of such waste separately
for special treatment is necessary.
5
For detailed operating method read the co rresponding content on the instruction manual.
For each wash cycle.
For programs with pre-wash,please put the detergent anywhere inside the
inner tank except in compartment A
(Follow the user instructions!)
Electric indicator on control panel (if provided).
Check the rinse aid level
(On models with water softener system only.)
Electric indicator on control panel (if provided).
If there is no salt warning light in the control panel
(for some models), you can estimate when to fill the salt into
the softener by the number of cycles the dishwasher has run.
Check the regeneration
salt level
Load the baskets
Select a programme
Running the dishwasher
Switch off the appliance
Turn off the water tap,
unload the baskets
Fill the detergent dispenser
Warning: wait a few minutes (about 15 m inutes ) befo re unloading the dis hwasher to avoid
han dling the dis hes and utensils w hile they are still hot and more suscep tible t o brea k.
The dishe s will also dry bett er. First start unloa ding the lower basket.
Changing the programme
Adding fo rgotte n dish es
in the dishwash er.
To load the baskets, ref er to th e sect ion entitled ." Prepa ring and Loading D ishes"
Touch the Programme B utton until th e sele cted p rogram me lights up.
( See the section entitle d Operation instr uction )“ ”
If the appliance is switched
off during a wash cycle.
Open the door care fully.
Look out for hot ste am
when openin g the door!
If the appliance is switched off during a wash cycle, when switched
on again, please re-select the washing cycle and operate the dishwasher
according to the original Power-on state ).
Switch on the appliance Open the door, the On/Off button to switch on the appliance .
touch
1.Open the door a little to stop the dishwasher.
2.After the spray arms stop working, you can open the door completely.
3.Add the forgotten dishes.
4.Close the door, the dishwasher will start running again .
When the working cycle has finished, the buzzer of the dishwasher will sound 8 times, then stop.
Turn off the appliance using the On/Off Button.
Since the appliance is standing by, it will power off automaticly after 30 minutes without any operation.
1. A running cycle can only be modified if it has been running for a short time. Otherwise the detergent
may have already been released and the water already drained. If this is the case, the detergent
dispenser must be refilled.
2. the start/pause button to stop the washing, press the for more than 3
seconds to cancel the running programme.
3. Select a new programme.
4. Restart the dishwasher.
Programme Button
Touch
Turn on the wate r tap and pre ss the Start/Pause Butto n. The machine will start working afte r
about 10 seconds.
before using it for the first time.
To get the best performance from your dishwasher, read all operating instructions
1.On/Off Button: To turn on/off the power supply.
3.Dela y Button s :
2.Prog ram Button : the button to s elect a
wash Program.
Touch
7.Di splay screen: to show the ti me
and the stat e(runn ing state, de lay time etc )
remaining
Back View
Increase
Decrease
4.
Half lo ad button:Dual zone wash fun ctio n. Touch the
button to s elect eith er upper basket or lo wer basket l oad.
The co rrespond ing response indica tor w ill light.
5. Function Button : the button to select a
function,
and the response indicator will blinking,
only one function can be selected in one cycle.
Touch
6.Start /Pause but ton: To start the selected
washin g pro gram or p ause the washing p rogram
when the machine is working.
Upper basket
Lower basket
Extra Drying, to improve drying efficiency.
Strong Wash, to improve cl eaning efficiency.
Express, to reduce .program duratio n
Faucet is not open
Rinse detergent need to be refilled
Salt need to be refilled
Glas s
90Min
Rapid
Auto
Intensive
Normal
ECO
6
11
12
1
2
3
4
5
7
8
9
10
Low er basket
Salt contain er
Dispenser
Cup shelf
Spray arms
Filter assembly
Inlet pipe connector
Drain pipe
Upper basket
Cutlery rack
Top spray arm
1
Inner pipe
5
6
7
8
9
10
12
11
3
2
4
6
Front view
The water softener must be set manually, using the water hard ness dial.
The water softener is des igned to remove minerals and salts from the water, which woul d have
a detrimental or adverse effect on the operation of the app liance.
The more minerals there are, the harder your water is
The softener sho uld be adjusted according to the hard ness of the water in your area. Your local Water Authority
can advise you on the hardness o f the water in your area.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjustment in the amount of salt co nsumed bas ed on the ha rdness of
the water used. This is intended to optimise and customise the level o f salt consumption.
1.
2. Touch the button for more than 5 se conds t o start the water softe ner
setting mode within 60seconds after the appliance was switched on(Salt and
Rinse aid warning lights will be on periodically );
3. the button to select the proper set accor ding to ,
4. To end the setting mode, either touch the On/Off button or wait 5 sec onds
Start/pause
Touch Start/Pause
th e setting will change in the following sequence: H1->H2->H3->H4->H5->H6->H1;
Wi th th e do or c lose d, switch on the appliance;
seeting mode is on
the hardness of your local water
WATER SOFTENER
The hardness of the water varie s from place to place. If hard water is used in the dishwasher, de posits will
form on the dish es and utensils.
The applian ce i s equipped with a sp ecial softener that uses a salt container specifically des igned to eliminate
lime and minera ls from the water.
Contact your local water board for information on the hardness of your water supply.
H1
H2
H3
H4
Please follo w the steps below for adjustm ent in salt consumption.
7
If your model does not have any water softener, you may skip this section.
H5
H6
The manufactory setting: H3 (EN 50242)
Before using you r dishwasher for the first time:
A. Set the water softener
B. Add 1.5Kg dishwasher salt and then full fill the salt container with water
C. Fill the rinse aid dispenser
D. Fill in detergent
Clark: British degree
fH: French degree
dH: German degree
dH=1.25 Clarke=1.78 fH=0.178mmol/l
1
dH
mmol/l
0~90~5 0~0.94 0
10-20
6-11
1.0-2.0 9
21-3012-17 2.1 -3.0 12
20
fH
0~6
7-14
15-21
Clarke
WATER HARDN ESS
Sel ector Position
Salt con sumption
(gram/cycle)
18-22 31-40 2 2-28 3.1-4.0
41-6023-34 4.1 -6.0 30
60
29-42
35-55 61-98 4 3-69 6.1-9.8
1. The salt container must only be refil led when the salt warning light in the control panel comes on.
Depending on how well the salt dissolve s, the salt warning light may still be on even though the
salt container is filled.
If there is no salt w arning light in the con trol panel (for some Mode ls),you can estimate when to f ill
the salt into the softener by the cycles that the dishwasher has run.
2.
I f salt has spilled, run a soak or quick prog ram to r emove it.
Always use the salt intended for dishwasher use.
The salt contain er is located beneath the lower basket and should be filled as explained
in the following:
Warning!
Only use salt specifically desi gne d for d ishwashers use! Every other type of
salt not specifically desig ned for dishwasher use, e specially table salt, will
damage the water softener. In case of damages caused by the use of unsuitable
salt the ma nufacturer does not give any warranty nor is liable for any damages caused.
Only fill wi th salt before running a cycle.
This wi ll prevent any grains of salt or salty wate r, which ma y have been spilled,
remaining on the bottom of the machi ne for any period of time, which may cause
corrosion.
8
Rinse Aid Dispenser
Function of Rinse Aid
Rinse aid is automatically added d uring the last rinse, ensuring thorough rinsing, a s pot and streak free drying.
Warning!
Only use branded rinse aid for dishwasher. Never fill the rinse aid dis penser with any other substances
(e.g. Di shwasher cleaning agent, liquid detergent). Th is would damage the app lian ce.
with wate r, It is normal f or a small amount of wa te r to
come out of the salt container.
Fill the salt cont ai ner to its maximu m li mit
A After the low er basket has been removed, unscrew and remove the cap from the salt container.
B Place the end of the funnel (supplied) into the hole and introduce about 1.5kg of di shwasher salt.
C
D Af ter fil ling the container ,
screw back the cap tightly.
E The salt warning light will stop being after th e sa lt contain er has be en fi ll ed with salt.
F Imm ediat ely aft er filling the salt into the salt container, a washing program should be started
program Other wise the filter system, pump or ot her important parts of t he machine may be damaged
by salty water. This is out of warranty.
(We su ggest to use a short
).
The rinse aid is released during the final rinse to prevent wa ter from formi ng droplets on your di shes, which can
leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is
designed to use liquid rinse aids. The rinse aid dispenser is located insid e, on the door and next to the detergent
dispenser.
To fill the dispenser, open the cap and pou r the rinse aid into the dispenser until the level indicator turns completely
black. The volume of t he rinse aid c ontainer is about 110ml.
9
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Careful ly po ur in the r inse-aid in to its dispenser, whil st avoiding i t to overflo w.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
Adjusting Rinse Aid Dispenser
The rinse aid dispenser has six or fou r s etting s. Always st art with the dispe nser
set on "4". If spot s and poor drying are a problem, increase the amount of rinse
aid dispensed by removing the dispenser lid and rotating the dial to "5". If the
dishes still are no t drying properly o r show spots, adjust the dial t o the next
higher lever until your dish es a re sp ot-free. The recommended setting is "4".
(Factory value is "4".)
Increase the dose if there are drops of water o r lime spots on the di shes after washing.
Reduce i t if there are sticky whitis h stains on your dish es o r a bluish fil m on glass ware or
knife blad es.
1
2
3
As the rinse aid d iminishes, the size o f the black dot
on the rinse aid level indicator changes, as illustra ted below.
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
When to Refill the Rinse Aid Dispenser
Unless the rinse-ai d warning light on the control panel is on, you can always estimate the amount from the color
of the optical level indicator "C "located nex t to the c ap. When th e rinse-aid container is f ull, the indicator
will be fully dark. The size of the dar k dot decreases as t he rinse-aid diminishes. You should neve r let
the rinse aid level be less than 1/4 full.
during the next wash. Don't forget t o re place the cap be fore you close dis hwa sher door.
Clean up any rinse aid spil led while during fillin g wit h an absorbent cloth to avoid excess ive foaming
The chemical ingredients that compose the detergent are necessary to remove, crush and dispense all dirt out of the
di sh washe r. Most of the commercial qualit y detergen ts are suitable for this pu rpose.
" "
Proper Use of Detergent
Use only detergent specifically made for the use in dishwashers. Keep your detergent fresh and dry.
Don't put powdered detergent into the dispenser u ntil you're re ady to wash dishes.
Warning!
10
Amount of Detergent to Use
Dishwasher detergent is corrosive!
Take care to keep it out of reach of children.
Based on their chem ical composition, deterge nts can be split in two basic types:
Dete rgent tablet s of different brands disso lve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power dur ing short
prog rams. Therefore please use l ong programs when u sin g deterg ent tablets, to
ensure the complete removal of detergent residuals.
The dispenser must be re filled before the start of each wash cycle following the instructions
provided in t he w ash cycle table . Your dishwa sher uses less de tergent and rinse aid than
Conventional dis hwa sher. Generally, only one tablespoon of detergent is needed for
a normal wash load. More heavily soiled items need more detergent. Al ways add the
detergent just be fore starting the dishwas her, otherwise it could get damp and will not
dissolve properly.
Concentrated Detergent
Detergent Tablets
Detergent Dispenser
co nventional, alkaline dete rgents with caus tic comp onents
low alkaline concentrated detergents with natural enzymes
Normally new pulverised detergent is without phosphate. Thus the water softener fu nction of
phospha te is not given. In this case we recommend to fill salt in the salt con tainer even w hen
the hardness of water is only 6 dH. If detergents witho ut phosphate are used in the case of hard water
often white spots appear on d ishes and glasses. In this case please add more detergent to reach
better results. Detergents without chlorine do only bleach a little. S tron g and coloured spots will not
be removed completely. In this case please choose a program with a hi gher temperature.
°
Detergents
There are 3 sorts of d etergents
1.With phosphate and with ch lorine
2.With phosphate and without chlorine
3.Without phosphate and without chlorine
Always add the detergent just before starting each wash cycle.
Only use branded detergent aid for dishwasher.
If the lid is closed: press release button. The lid will spring open.
Detergent powder
11
Fill the detergent dispenser with deter gen t.
The marking indicates the dosing leve ls , as
Illustrated :on the right
Plea se observe the m anufact urers do sing and storage
Recommendations as stated on the detergent packaging.
Close the lid a nd press on it until it locks into place.
If the dishes are heavily soiled , add an additional prewash detergent dose.
This detergent wi ll take effect during the pre-wash phase.
Filling the detergent dispenser
You information about the a mount of detergent for the single programme on page 14.
will f ind
Be aware that dep end ing on th e so iling of wate r, se tting ma y be diffe ren t.
Please observe the manufa cturer's recommendations on the detergent packaging.
1. Place the main washing cycle detergent in the storage
compartment indicated with an A on the picture.
Th e marking on the compartment indica tes t he dosing
level.
2. Place pre-wash detergent cycle detergent anywhere
inside the inner tank
“ ”
12
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic ite ms that are not heat resistant
Older cutlery with glued parts t hat are not
temperature resistant
Bonded cutlery items or dishes
Pewter or cooper items
Crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Some types of glasses can become
dull after a large number of washes
Silver and aluminum parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
Are not suitable
Are of limited suitability
Dishes and items of cutlery must not lie inside one another, or cover each oth er.
The upper basket is designed to ho ld more delicate and lighter dishware such as glasses , coffee
and tea cups
Long bladed knive s stored in an upright position are a potential hazard!
Long and/or sharp items o f cutlery such as carving knives must be positioned
horizontally in the upper basket.
Please do not ove rload your dishwasher. This is important for good results and for
reasonab le consumption of energy.
To avoid damage , gla sses should not touc h on e an other.
Load large and difficult to clean it ems in the lower basket.
Load hollow items such as cups, glasses, pans etc. With the opening facing downwards so that
water can not collect in the container or a deep base.
Consider buying utensils which are identified as dishwasher-proof.
Use a mild detergent that is described as 'kind to dishes'. If necessary, seek further
information from the detergent manufacturers.
For particular items, select a program with
To prevent damage, do not take gla ss a nd cutlery out of the dishwasher immediately
after the programme has ended.
t he lo west possible temperature.
(For best performance of the dishwasher, follow the se loading guide lines.
Features and appearance of baske ts and cutlery ba skets may vary from your model.)
Scrape off any large amounts of leftover food. Soften remnants of burnt food in pans.
It is not necess ary to rinse the d ishes under running water.
Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots /pans, etc. are faced downwards.
2.Curved items, or ones with recesses, should be loaded aslant so th at water can run off.
3.All utensils are stacked securely and can not tip over.
4.All utensils are placed in the way that t he spray arms can rotate freely during washing.
Very small items should not be washed in the dishwasher as they could easily fall out of the basket.
To prevent water dripping from the uppe r basket into the lower basket, we recommend that you
empty the lower basket first
, follow ed by the
upper basket.
13
For better stacking of pots and pans, the spikes can be folded
down as show on the picture below.
The u pper basket is designed to hold more delicate
and lighter dishware such as glasses, coffee and
tea cups and saucers, as well as pl ates, sm all bowls
and shallow pans (as long as they are not too dirty).
Position the dishe s an d co okware so that they will
not get moved by the spray of wate r.
Pots, serving bowls, etc, must alw ays be placed top down.
Deep pots should be slan ted to allow water to flow out.
Please be reminded that:
The B otto m Basket featur es folding spikes so that larger or more pots and pans can be loaded.
They do not nest together.
Silverware is placed with the male face up.
Long utensils in the middle.
Cutlery should be placed in the cut lery basket with the handles at the bottom. If the rack has side baskets, the
spoons should be loaded separately into the appropriate slots, utensils should be placed in the
horizontal position at the front of the upper basket .
Especially long
Do not let any item extend through the bottom.
Always load sharp utensils with the sharp point down!
The height of th e up per rack can be easi ly ad just ed to
accommodate taller dishes in ei ther the upper an d lo wer
rack. To rai se th e ra ck t o the upper position, lift rack until
both sides are a t the same h eight. The rack will secur e
into pla ce. To lo wer the rack , pu sh down on the h andle
and release.
For better st acking of cups, the sh elves can be folded
down as show on the picture belo w.
We suggest that you place large items and the most
difficult to clean items such as
pots, pans, lids, serving dishes and bowls, as shown
in the figure below. It is preferable to place serving
dishes and lids on the side of the racks in order to
avoid blocking the rotation of the top spray arm.
into the lower bask et:
For a top quality cleaning, place the silverware in the basket making sure that:
14
*EN 50242 : This p rogramme is the test cycle. The informat ion for comparability test
in accord ance with EN 502 42, as follows:
Capacity: 15 setting
Position Upp er basket:
Rinse aid setting: 6
Pl:0.49w ; Po:0.45w.
lower position
Means: need to fill rinse into the Rinse-Aid Dispenser.
( )
(* EN 5 024 2)
For normally soiled loads,
such as p ots plates
glasses an d lightly
soiled pans.
、 、
For heavi est s oiled crockery,
and normally soiled pots
pans dishes etc with dried
on soiling.
、
、
A shorter wash for lightly
soiled loads a nd quick
wash.
Pre-wash(50 )
Wash (60 )
Rinse
Rinse
Rinse( 70 )
Drying
℃
℃
℃
Pre-wash(45 )
Wash (55 )
Rinse
Rinse (65 )
Drying
℃
℃
℃
Wash (45 )
Drying
Pre-wash
Rinse(65 )
℃
℃
Wash (45 )
Rinse
Rinse (55 )
℃
℃
(50 )℃
185
220
175
30
1.3
0.86
1.6
0.75
17.5
13.5
10
11
(65 )
Wash
Rinse (65 )
Drying
Pre-wash
℃
℃
90 12.51.35
For lightly soi led cr ockery
and glass.
130 0.9 13
Wash (40 )
Ri nse
Dr ying
Pr e-w ash
Ri nse(60 )
℃
℃
Auto sensing wash, lightly,
norm ally or heavily soiled
crock ery, wi th or with out
dried-on food
Pre-wash (45 )
Autowash(45-55 )
Rinse
Rinse (65 )
Drying
℃
℃
℃
150
0.9~1.3 11~15
Auto
This is standard programme,
it is suitable to clean normally
soiled tableware and it is the
most efficient programme in
terms of its combined energ y
and water consumption for
that type of tableware.
For normally soiled loads
th at need quick wash.
5/30g
1or2 pi eces
5/30g
1or2 pieces
35g
1 piece
25g
5/30g
1 piece
5/30g
1or2 pieces
5/30g
1or2 pieces
Starting a cycle wash
Draw out the lower and upper basket, load the dishes and push them back.
It is commen ded to load the lower basket first, then the upper one (see t he section entitled
Loading the Dishwasher ).
Pour in the deter gent (see the section entitled ).
Inse rt the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification
of the so cket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
Close the do or, press the On/Off button to swit ch on the machine.
Press the program button , the wash program will b e ch anged as follows direction:
If a program is selected, the response ligh t will light on. Then press the Start/Pause button, the
dish washer
“ ”
“ ”
Auto Intensive->Normal->ECO->Glass ->Rapid;-> ->90 min
1
2
3
4
5
Prior to first time use
will start its cycle.
15
A forgotten dish can be added any time before the detergent cup opens.
Add forgotten dishes.
Close the door
After the spray arms stop working, you can open the door
completely.
2
3
Open the door a little .
1
4
5
The dishwasher will start running again.
It is dangerous to open the door mid-cycle,
as hot steam may scald you.
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off
the appliance usi ng the ON/OFF button, shut off the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid ha ndlin g the dishes and utensils while th ey
are still hot and m ore susceptible to break. They will also dry be tter.
Open the door carefully.
Hot dishes are sensitive to minutes before removing from
the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they
will be cooler and the drying will be improved.
shocks. The dishes should cool down for around 15
Unloading the dishwasher
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto
the dishes in the lower one.
It is normal for the dishwasher to be wet inside.
Switching Off the Dishwasher
The pro gram light is on but is not blin kin g, only in this case has the programme ended.
1.Switch off the dishwasher by p ressing the O N/OFF button.
2.Turn off the water tap!
If you open the door , the machine will pause. The colon in the
display will stop blinking and the buzzer will every minute unless you close the door .
After you close the door ,the machine will keep on working after 10 seconds.
during a wash cycle
sound
Premise:
1 A ru nning cycle can on ly be chan ged if it has only been running for a short time. Othe rwise, the detergent may
have already been released, and the appliance may have alr eady drained t he wash water. If this is the case,
the detergent dispenser must be refilled (see the section entitled F ).
2 Press the start/pause to sto p the washing, press the Program button ,
the machine will b e in standby state, then you can change the program to t he desired cycle setting
(see the section entitled " S tarti ng a washing program ).
more than 3 seconds
"
illing the deteregent dispenser
The filter prevents lar ger remnant s of food or other objects from getting insi de th e pump.
The residues may block the filter, in this case they must be rem oved.
The filter system consists of a coarse filter,a flat (Main f ilter)
And a microfilter(Fine filter).
Fo od and soil particles trap ped in this filter are pulverized by a
special jet on the lower spray arm and w ashed down drain.
La rger items, such as pieces of bones o r glass, that could block
the drain are trapped in the coarse filter. To remove the items
caught by the filter, gently squeeze the tap on th e top of this
filter and lift out.
This filter holds soil and food residues in the sum p a rea and
prevents
them fr om b eing redeposite d on the dish es d urin g wash cycle.
Main filter
1
Coarse filter
2
Fine filter
3
2
3
1
Filter assembly
The filter efficiently
For best performance and results, the filter must be cleaned regularly. this reason, it is a goo d idea to
remove the larger food particl es trapped in the filter aft er e ach was h cy cle by rinsing the sem icircular filte r and
cup under runnin g water. To remove the filter device, pull the cup handle in t he upward d irection.
remo ves f ood particle s from the wash water, allowing it to be rec ycle d during the cycle.
For
The d ishw asher must never be used without the filters.
Improper replacement of the f ilter may reduce the performance level of the appliance
and dama ge dishes and utensils.
Step 1 Turn the：
filter counterclockwise,
Step 2 lift the filter assy up：
When following this procedure from step1 to step 2, the filter system will be removed;
when following it from Step 2 to Step 1, the filter system will be installed.
16
1
2
17
The control pane l can be cleaned by using a lightly dampened cloth.
After cleaning, m ake sure to dry it thoroughly.
For the exterior, use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on a ny part of the dishwasher.
Winterzing
1 .Cut off the electrical power to the dishwasher at the supply source.
2. Turn off the water supply and disconnect the water inlet pipe from the water valve.
3. Drain the water from the inlet pipe and water valve. ( Use a pan to gather the water)
4. Reconnect the water inlet pipe t o the water valve.
5. Remov e the filt er at the bottom of the tub and use a sponge to soak up water in the sump.
please take frost protection measures on the dishwasher in winter. Every fter washing cycles,
please operate as follows
time a
：
Cleaning the Filter
Cleaning The Door
To clea n the coarse filte r an d the fine filt er, use a clea ning brush. Rea ssem ble the filter parts (see page 16) and
rei nsert them in the dishwasher, pos ition ing them in their sea t and pressing downw ards.
When cleaning the filters, Otherwise, the filters could be
contorted and the performance of the dishwasher could be decreased.
do not knock the m.
To cle an the edge around the door, you
To avoid pene tration o f water into the door lock and electrical components, do not
use a spray cleaner of any kind.
sh ould only use a s oft, ward and damp
cloth.
Never u se a spray cleaner to clean t he door panel as it may damage the door lock
and electrical components.
Abrasive ag ents or some paper towels should not be used because of the risk of
scratching or leaving spots on the stainless steel surface.
Cleaning the Spray Arms
If your dishwasher cannot work because of the ice,
please contact professional service persons.
It is necessary to clean the spra y arms re gularly fo r hard
wate r chemicals will clog the sp ray arm jets and bearings.
- After each cyc le, c heck for any debris in the filte r to avoid future b lock age.
- By unscrewing the coarse filter, you can rem ove the filter system. Remove any foo d remna nts and
clean the fi lters under running water.
Remarks:
The entire filter assembly should be cleaned once a week.
To remove th e lower spray arm, pull out the spr ay arm u pwa rd.
To remove the up per spray arm, hold the nut, rotate the arm
clockwise to remove it.
Wash the arms in soapy and warm water and use a soft brush to
clean the jets. Replace them after rinsing them thoroughly.
It is recommend t hat you run a was h cy cle with the
dishwasher empty and the n remove the plug from the
sock et, turn off the water supply and leave the door of
the appliance slightly open. This w ill help the door
seals to last l onger and prevent odours from forming
within the appliance.
If the appliance must be moved, try to keep it in the
vertical position. If absolutely necessary, it can be
positioned on its back.
One of the factors that cause odours to form in the
dishwasher n the seals.
Periodic cleaning with a damp sponge will prevent this
from occurring.
is rema inin g food strapped i
Before cleaning or performing maintenance, always
remove the plug from the socket.
To clean the e xterior and rubber parts of the di shwasher,
do not use solvents or abrasive cleaning products.
Only use a cloth with warm soapy water.
To remove spots o r stains from the surface of t he
interior, use a cloth dampened with water a n a little
vinegar, o r a cleaning product mad e specifically for
dishwashers.
Remove the Plug
No Solvents or Abrasive Cleaning
Moving the Appliance
Seals
After every wash, turn off the water supply to the
appliance and leave the door slightly open so that
moisture and odours are not tra pped inside.
After Every Wash
When not in use for a Timelong
18
Th e installation of t he pipes
and electrical equipments
should be done by professionals .
Electrical Shock electrical power
dishwasher.
Failure to do so can result in death or electrical shock.
Hazard. Disconnect
before installing
The installation position of dishwasher should be ne ar t he existing inlet and drain hoses and power co rd.
One side of the ca binet sink should be chosen to facilitate the connection of drain hoses of the dishwasher.
Installation preparation
Note: please che ck the accompanying installation accessories(hook for aes thetic panel,screw)
●
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
