COPYRIGHT © 2009 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
CUTTING STAND FOR
5” “DOUBLE CUT
TM” SAW
COUNTER-ROTATING TWIN BLADE TECHNOLOGY
INSTRUCTION MANUAL
MODEL: KW-9115
WARRANTY INFORMATION
2-YEAR
LIMITED WARRANTY
FOR
THIS CUTTING STAND
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
REPLACEMENT PARTS
Replacement parts for this product are available through our authorized King
Canada service centers across Canada. Please refer to the Parts section of the
King Canada web site (www.kingcanada.com) for parts diagram and parts list.
LIMITED TOOL WARRANTY
King Canada makes every effort to ensure that this product meets high quality and
durability standards. King Canada warrants to the original retail consumer a 2-year
limited warranty as of the date the product was purchased at retail and that each
product is free from defects in materials. Warranty does not apply to defects due
directly or indirectly to misuse, abuse, normal wear and tear, negligence or
accidents, repairs done by an unauthorized service center, alterations and lack of
maintenance. King Canada shall in no event be liable for death, injuries to persons
or property or for incidental, special or consequential damages arising from the use
of our products.
To take advantage of this limited warranty, return the product at your expense
together with your dated proof of purshase to an authorized King Canada service
center. Contact your retailer or visit our web site at www.kingcanada.com for an
updated listing of our authorized service centers. In cooperation with our authorized
serviced center, King Canada will either repair or replace the product if any part or
parts covered under this warranty which examination proves to be defective in
workmanship or material during the warranty period.
NOTE T
O USER
This instruction manual is ment to serve as a guide only. Specifications and
references are subject to change without prior notice.
KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4
www.kingcanada.com
SAFETY & ASSEMBLY
WARNING! SAFETY PROCEDURES
1. The “Double Cut” Saw to be used with this cutting stand must be in good condition.
2. Make sure the cutting stand is fixed on work bench or ground base.
3. Make sure the power cord is positioned in left rear corner of the cutting stand.
Avoid
direct contact of power cord with cutting material and chips.
4. Make sure the work area is clean and bright.
5. Do not operate “Double Cut” Saw under explosive environment containing explosive
liquid, gas, or dusts.
6. Keep children or bystander away when performing cutting operations.
7. Make sure “Double Cut” Saw is “OFF” and unplugged from the power source when
mounting it onto the cutting stand.
8. Adjust the upper and lower blade guard asembly position to make sure the scraps do
not fly towards the operator.
9. Make sure to secure the cutting materials when performing cutting operations.
ASSEMBLY
1. Install the quick release vise assembly (A) Fig.1 to the stand base (B) using hex. bolts,
spring washers, washers and hex. nuts.
2. Before tightening the hex. nuts, make sure the slot washer (A) Fig.2 is positioned under
the base slot as shown in Fig.2.
This will prevent the quick release vise from lifting
upwards.
3. Install the miter gauge (C) Fig.1 to the slot in the base (B) using 2 hex. bolts, a
washer and 2 hex. nuts.
FIGURE 1
FIGURE 2
ASSEMBLY
4. Fix the aluminum bracket and the main frame
assembly (A) Fig.3 to the stand base (B) using
hex. bolts, washers and hex. nuts.
5.
Attach the drawspring (C) to the aluminum
bracket and the main frame assembly.
6. Assemble the handle knob and down handle (D)
to the main frame.
7. In order to install the “Double Cut” Saw on the
cutting stand, first the control handle and
bracket must be removed from the tool. Then
the blade guard assembly (B) Fig.4 must be
pivoted around to allow the blade to be exposed
after installation. Loosen blade guard assembly
screw (A) Fig.4. Retighten screw after you have
installed the tool on the cutting stand and have
adjusted the blade guard assembly position.
8. Place the “Double Cut” Saw onto the main frame
and secure it in place using two main frame hex.
bolts and washers (above and below). It is
important that the “Double Cut” Saw be
perfectly aligned with the base groove, to do so,
loosen the hex. nuts (A) Fig.5 on the
adjustment bolts (B) and adjust the bolts in or
out until the tool is perfectly aligned with the
base groove. Once done, retighten the hex.
nuts. Secure all hardware mentioned in this
step.
9. Install the spark guard (A) Fig.6 to the tip of the
lower blade guard (B) using the spark guard
screw and wing nut (C).
Warning!: T
ighten all the bolts and nuts before
operating.
FIGURE 3
FIGURE 4
ASSEMBLY
FIGURE 5
FIGURE 6
OPERATION
OPERATION PROCEDURES
1. Place the workpiece on the base (A) Fig.7 in
between the miter gauge (B) and the quick
release vise (C). Position the miter gauge in the
desired angle and secure it with the hex. bolt
and washer (D). Then press the quick release
vise button (E), push the handle (F) to position
the vise up against the workpiece and release
the quick release vise button. Turn the handle
clockwise until your workpiece is secured to the
base.
2. Support the cutting material with your left hand
and hold the down handle (A) Fig.8 and the
switch lever (B) with your right hand.
3. To begin the cutting operation, pull the switch
lever (B) to activate the “Double Cut” saw switch
and turn the tool on. Push the down handle (A)
towards the workpiece to cut. Release the switch
lever to turn the “Double Cut” saw off.
FIGURE 7
FIGURE 8
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
King Canada PDM-30 User manual
-
-
-
-
-
-
-
-
-