HP t410 All-in-One Smart Zero Client User guide

Type
User guide

This manual is also suitable for

HP Smart/Zero Client 4.1.2
Administrator's Guide
© Copyright 2011, 2012 Hewlett-Packard
Development Company, L.P. The information
contained herein is subject to change
without notice.
Microsoft, Windows, and Vista are
trademarks of Microsoft Corporation in the
U.S. and other countries.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be
construed as constituting an additional
warranty. HP shall not be liable for technical
or editorial errors or omissions contained
herein.
This document contains proprietary
information that is protected by copyright.
No part of this document may be
photocopied, reproduced, or translated to
another language without the prior written
consent of Hewlett-Packard Company.
Third Edition (August 2012)
First Edition (June 2011)
Document Part Number: 654363–003
About This Book
WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily
harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage
to equipment or loss of information.
NOTE: Text set off in this manner provides important supplemental information.
If you have comments, feedback, or questions about this guide, please e-mail us at
iii
iv About This Book
Table of contents
1 Quick Start ....................................................................................................................... 1
Installing HP Smart Client Services .............................................................................................. 2
Standard installation .................................................................................................. 2
Booting client .......................................................................................................................... 3
Quick troubleshooting ............................................................................................................... 3
2 Server setup ..................................................................................................................... 4
How it works ........................................................................................................................... 4
HP Smart Client Services ........................................................................................................... 5
Supported operating systems ...................................................................................... 5
Prerequisites ............................................................................................................. 6
Installing Internet Information Services (IIS) ..................................................... 6
.NET Framework 3.5 .................................................................................. 8
How to install via Add Windows features ....................................... 8
Web download (Windows XP, Windows Vista®, Windows
Server 2003) .............................................................................. 9
Using HP Smart Client Services ................................................................................. 10
Installing custom setup .............................................................................. 10
Modifying, adding, repairing, or deleting HP Smart Client Services features .... 11
Using Profile Editor ................................................................................................................. 13
Changing your server/URL ....................................................................................... 14
Configuring platform settings .................................................................................... 14
Modifying client settings ........................................................................................... 15
How to use the tree view ........................................................................... 16
Changing settings ..................................................................... 16
Changing the keyboard language ............................................... 16
How to read the side information bar ......................................................... 18
Common settings to change ....................................................................... 18
Disabling and enabling items .................................................................... 18
Disabling Configure menu items .................................................. 19
Disabling Additional Configurations menu items ............................ 20
Finishing and saving your settings ............................................... 21
v
Attaching client files to a profile ................................................................................ 21
About installing certificates ........................................................................ 21
Installing Citrix Certificates on Smart Zero Core 4.1.0 and earlier versions ..... 22
Customized login screen ........................................................................... 22
Screen background customization ............................................... 22
Login dialog customization ......................................................... 28
Saving profiles ........................................................................................................ 30
Parallel and serial printer port setup .......................................................................... 30
Automatic intelligence ............................................................................................................. 31
Viewing your HP Smart Client Services website ........................................................... 32
Automatic Intelligence directory structure .................................................................... 32
MAC address-based profile ...................................................................................... 32
Updating thin clients ................................................................................................ 33
Broadcast update ..................................................................................... 33
DHCP Tag setup on Windows Server 2003/2008 for Automatic Intelligence
update .................................................................................................... 34
DNS alias ............................................................................................... 37
Manual update ........................................................................................ 37
HP Intelligent Delivery Service .................................................................................................. 39
HP Device Manager ............................................................................................................... 41
3 Client Usage ................................................................................................................... 42
Demo mode (no server configured) ........................................................................................... 42
Connections .......................................................................................................................... 43
RDP ....................................................................................................................... 43
ICA ....................................................................................................................... 44
VMware View ........................................................................................................ 44
Connecting to VMware View ..................................................................... 44
Using the System Control pane ................................................................................................ 45
Shutdown/restart .................................................................................................... 45
Control panel ......................................................................................................... 46
Control panel menu .................................................................................. 46
Parallel and serial printer mapping ............................................................. 48
System information .................................................................................................. 49
Status tab ................................................................................................ 50
Network tab ............................................................................................ 51
Net Tools tab ........................................................................................... 51
System Information tab .............................................................................. 53
System Logs tab ....................................................................................... 53
Status icon ............................................................................................................. 54
USB boot .............................................................................................................................. 54
vi
Download image off web ......................................................................................... 54
Reimage device ...................................................................................................... 54
Retrieving System Diagnostics .................................................................................................. 55
What is System Diagnostics? .................................................................................... 55
Saving System Diagnostics ....................................................................................... 55
Opening System Diagnostics .................................................................................... 56
Windows ................................................................................................ 56
Linux/Unix .............................................................................................. 57
What to look for in System Diagnostics ...................................................................... 57
vii
viii
1Quick Start
If you just want to install HP Smart Client Services and get started, this section will guide you through
the following:
Installing HP Smart Client Services on page 2
Booting client on page 3
Quick troubleshooting on page 3
NOTE: Microsoft
®
Internet Information Services (IIS) in Windows
®
Server and Microsoft .NET
Framework 3.5 must be installed before you install HP Smart Client Services. For information on
installing IIS, visit
http://www.microsoft.com. If you have internet access, the HP Smart Client Services
installation wizard offers to install the .NET Framework 3.5 for you. If you do not have internet access,
you must manually install the Microsoft .NET Framework 3.5. Download Microsoft .NET Framework 3.5
from the Microsoft website at
http://www.microsoft.com/downloads/en/details.aspx?
FamilyId=333325fd-ae52-4e35-b531-508d977d32a6&displaylang=en.
1
Installing HP Smart Client Services
Standard installation
NOTE: Microsoft IIS and Microsoft .NET Framework 3.5 must be installed before you install HP Smart
Client Services.
1. Download HP Smart Client Services from HP.com.
2. Double-click HPSmartClientService_version number.exe to launch the HP Smart Client Services
installation wizard.
The InstallShield Wizard dialog box appears.
3. Select the language and click OK.
The Welcome to the InstallShield Wizard for HP Smart Client Service dialog box
appears.
4. Click Next to continue.
The Setup Type page opens.
5. Select Complete setup type, and click Next.
6. Select a connection type, and then click Next to continue.
7. Type the server URL in the field and click Next.
The Select Features page opens.
8. Check the appropriate box or boxes if you want Japanese and Chinese language support. Click
Next to continue.
The Ready to Install the Program dialog box appears.
9. Click Install to install HP Smart Client Services.
If you do not want to install HP Smart Client Services at this time, click Back to make changes or
Cancel to cancel installation.
If you click Install, HP Smart Client Services is installed and the InstallShield Wizard
Complete page opens.
10. If you want to launch the Profile Editor, select the check box and click Finish. If not, leave the
check box clear and click Finish to exit the wizard.
NOTE: The Profile Editor allows you to create and edit configuration files. For more information,
see
Using Profile Editor on page 13.
2 Chapter 1 Quick Start
Booting client
If HP Smart Client Services is enabled and configured to connect clients to a valid remote connection
server, the client will auto-configure and boot to a login screen. Users can then enter their credentials to
log in to the preconfigured remote connection server. If HP Smart Client Services is not enabled, users
will boot to the Demo Mode.
For more information, see
Client Usage on page 42.
Quick troubleshooting
Occasionally, everything does not go as planned. If you have gone through the previous sections but
HP Smart Client Services is not working, a number of additional actions can be taken to resolve the
problem. In this section, we will step through each point in the update process, verify that it is working,
and provide resolution guidance if the process is not working.
1. Test network connectivity:
a. Go to the Net Tools tab under System Information.
b. Select the Ping tool, type the server address under Target Host, and then click Start
Process.
If the ping is successful, you should receive output similar to this:
PING 10.30.8.52 (10.30.8.52) 56(84) bytes of data.
64 bytes from 10.30.8.52: icmp_seq=1 ttl=64 time=0.815 ms
64 bytes from 10.30.8.52: icmp_seq=2 ttl=64 time=0.735 ms
If you have a long delay with no output, your network may be disconnected.
c. Check the network cable and network settings in the Control Panel and system tools.
d. Try pinging other servers or clients.
e. If you can reach other clients on the network but not the server, ensure that you have the
correct server address.
f. Try pinging by IP address instead of Domain name or vice-versa.
g. In some rare cases, ping may be blocked on your network. If that is the case, skip to the next
step.
2. Check logs: The Smart Client Services log should give a clear indication if there are any problems
with the way the Smart Client server is set up.
a. Verify that there are no errors in the Smart Client Services logs.
b. If an Error: Server is not setup notification appears, verify that the Smart Client Server is
set up properly and Smart Client Services is running.
Booting client
3
2 Server setup
How it works on page 4
HP Smart Client Services on page 5
Using Profile Editor on page 13
Automatic intelligence on page 31
HP Intelligent Delivery Service on page 39
How it works
The HP Smart Client is designed to detect its update server automatically and to configure itself
automatically on first boot. This greatly simplifies device installation and maintenance. Refer to the
following diagram to see how the device communicates with the server to receive its profile and client
kits.
4Chapter 2 Server setup
HP Smart Client Services
Supported operating systems on page 5
Prerequisites on page 6
Using HP Smart Client Services on page 10
Supported operating systems
Windows 7
Windows Server 2003
Windows Server 2008
Windows Server 2008 R2
NOTE: The installer is 32-bit only, but it is supported on 32-bit and 64-bit versions of the Windows
operating system.
HP Smart Client Services
5
Prerequisites
Installing Internet Information Services (IIS) on page 6
.NET Framework 3.5 on page 8
Installing Internet Information Services (IIS)
IIS must be installed before HP Smart Client Services can be installed.
Installing IIS on Windows 7:
1. Click Start and select Control Panel.
2. Click Programs, and then click Turn Windows features on or off.
3. In the Windows Features dialog box, click Internet Information Services. and then click
OK.
Installing IIS on Windows Server 2003:
1. Click Start and select Control Panel.
2. Double-click Add or Remove Programs.
3. Click Add/Remove Windows Components.
4. In the Windows Component Wizard under Components, select Application Server,
and then click Next.
5. When the wizard has completed the installation, click Finish.
6Chapter 2 Server setup
Installing IIS on Windows Server 2008 or Windows Server 2008 R2
1. Click Start, select Administrative Tools, and then click Server manager.
2. Click Roles in the left pane.
3. In Roles Summary, click Add Roles in the right pane.
4. In the Select Server Roles dialog box, check the Web Server (IIS) check box.
5. Accept the default entries and click Next.
HP Smart Client Services
7
6. In the Confirm Installation Selections dialog box, click Install.
7. When the Installation Succeeded screen appears, click Close to end the installation.
.NET Framework 3.5
If you plan to use Windows Server 2008 R2, IIS must be installed before .NET Framework 3.5 is
enabled.
You do not have to manually install the .NET Framework 3.5 if you have internet access during the
installation of HP Smart Client Services. The installation wizard asks you if you would like to install
the .NET Framework 3.5. If you select to install, the process downloads and installs the .NET
Framework 3.5 without any user intervention. Users installing HP Smart Client Services without internet
access must manually install the Microsoft .NET Framework 3.5. The procedures to install the .NET
Framework 3.5 are below.
How to install via Add Windows features on page 8
Web download (Windows XP, Windows Vista
®
, Windows Server 2003) on page 9
How to install via Add Windows features
Windows 7 Operating System—The Microsoft .NET Framework 3.5 is already installed in
Windows 7.
To verify installation:
1. Click Start > Control Panel.
2. Click Programs, and then click Turn Windows features on or off.
3. If the Microsoft .NET Framework 3.5 option box is checked, then it is already installed.
If it is not checked, check the option box and click OK to turn the feature on.
Windows Server 2008 R2 Operating System—The Microsoft .NET Framework 3.5 is already
installed in Windows Server 2008 R2.
To verify installation:
1. Click Start > All Programs > Administrative Tools, and then select Server Manager.
8Chapter 2 Server setup
2. Click Features to display all the installed Features in the right hand pane.
If .NET Framework 3.5 is listed, it is installed.
3. If it is not installed, install it using one of the following methods:
Through the Server Manager interface:
a. In the Server Manager interface, select Add Features to display a list of possible
features.
b. In the Select Features interface, expand .NET Framework 3.5 Features.
c. Select .NET Framework 3.5 and click Next.
d. In the Confirm installation Selections dialog box, click Install.
e. Allow the installation to complete, and then click Close.
Using the command prompt:
a. Click Start > Programs > Accessories.
b. Right-click Command Prompt and select Run as Administrator.
c. In the command prompt, type Import-Module ServerManager, and then press Enter.
d. Type Add-WindowsFeature as-net-framework, and then press Enter.
An exit code as Success for .NET Framework 3.5. appears if installation was successful.
e. Type exit, and then press Enter to exit the Command Prompt.
Web download (Windows XP, Windows Vista
®
, Windows Server 2003)
If you do not have internet access, you must manually install the Microsoft .NET Framework 3.5.
Download Microsoft .NET Framework 3.5 from the Microsoft website at
http://www.microsoft.com/
downloads/en/details.aspx?FamilyId=333325fd-ae52-4e35-b531-508d977d32a6&displaylang=en.
HP Smart Client Services
9
Using HP Smart Client Services
To launch HP Smart Client Services, double-click HPSmartClientService_version number.exe (HP Smart
Client Services installation executable).
Installing custom setup on page 10
Modifying, adding, repairing, or deleting HP Smart Client Services features on page 11
Installing custom setup
NOTE: Microsoft IIS and Microsoft .NET Framework 3.5 must be installed before you install HP Smart
Client Services.
This is a custom installation of HP Smart Client Services.
1. Download HP Smart Client Services from HP.com.
2. Double-click HPSmartClientService_version number.exe to launch the HP Smart Client Services
installation wizard.
The InstallShield Wizard dialog box appears.
3. Select the language and click OK.
The Welcome to the InstallShield Wizard for HP Smart Client Service dialog box
appears.
4. Click Next to continue.
The Setup Type page opens.
5. Select Custom setup type, and then click Next to continue.
6. Click Next to accept the default folder where setup will install files.
The Select Features page opens.
7. Select the features you want to install, and then click Next to continue.
8. Select a connection type, and then click Next to continue.
9. Type the server URL in the field and click Next.
The Select Features page opens.
10. Check the appropriate box or boxes if you want Japanese and Chinese language support. Click
Next to continue.
The Ready to Install the Program dialog box appears.
11. Click Install to install HP Smart Client Services.
If you do not want to install HP Smart Client Services at this time, click Back to make changes or
Cancel to cancel installation.
10 Chapter 2 Server setup
If you click Install, HP Smart Client Services is installed and the InstallShield Wizard
Complete page opens.
12. If you want to launch the Profile Editor, select the check box and click Finish. If not, leave the
check box clear and click Finish to exit the wizard.
NOTE: The Profile Editor allows you to create and edit configuration files. For more information,
see
Using Profile Editor on page 13.
Modifying, adding, repairing, or deleting HP Smart Client Services features
You can modify, add, delete, or repair HP Smart Client Services features as needed.
1. Open the HP Smart Client Service – InstallShield Wizard using one of the following
methods:
Double-click the HP Smart Client Services setup icon.
Use the Control Panel.
a. Click Start and open the Control Panel.
b. Double-click Uninstall a program to open a list of programs. Right-click HP Smart
Client Service and select Change to open the HP Smart Client Service
InstallShield Wizard.
2. Modify the installation, if you want to add a feature.
a. Select Modify, and then click Next.
b. Select features to install. Click a check box to select a feature and clear a check box to
deselect a feature. Click Next.
If you selected the Automatic Intelligence feature, a Files in Use dialog box appears.
c. If a Files in Use dialog box appears, select one of the options and click OK.
The Maintenance Complete dialog box appears.
d. Click Finish.
HP Smart Client Services
11
3. Repair the installation if you have corrupted or deleted install files. Choose this option to perform a
complete reinstallation of HP Smart Client Services.
a. Select Repair, and then click Next.
The Maintenance Complete dialog box appears.
b. Click Finish.
4. Remove HP Smart Client Services if you wish to remove all installed features.
NOTE: Profiles and packages are not deleted by default.
a. Select Remove and click Next.
HP Smart Client Services is uninstalled and the Uninstall Complete page opens.
b. If you want to Uninstall all the HP Smart Client Service profiles and packages,
select the check box and click Finish. If not, leave the check box clear and click Finish to
exit the wizard.
12 Chapter 2 Server setup
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65

HP t410 All-in-One Smart Zero Client User guide

Type
User guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI