Channel Vision IR-2400 User manual

Type
User manual
1 2
3
4
5
6
7 8 9
0
Power
Besuretheemitterisattacheddirectlyoverthecomponent’sIRreceiver.
TolocatetheIRreceiver,shineaflashlightintotheunitandlookforthe
sensor.
HowIRrepeatingworks
Specifications: (typical)
VoltageRequirements:
IRFreq.rangesupported:
IRpickuprange:
IRreceiverheaddimensions:
Color:
8-12VDC
30kHz-60kHz
40ft.@38kHz,25ft.@56kHz
0.65” x0.35” x0.25”
Black
Specificationssubjecttochangewithoutnotice.
TheIR-2400includestheseitems:
500-153revC
1-IRreceiverholster
1-holemount
1-tabletopmount
IRreceiverhead
+V
Gnd.
Sig.
36”
Features:
!
!
!
PlasmaProofIRreceiver
StatusLEDsforIRsignalindication
Versatilemountingaccessaries:Installas
Verysmallreceiver
In-cabinettubetypereceiver
Unobtrusivedesktoptypereceiver
+V
(whitedashorbrownwire)
Endview
ribboncable
Ring
Tip
Collar
+V
Gnd
Sig
TypicalIRreceiver
connections(refonly)
IRreceiverwirepinout
Pointan
IRremotecontrol
attheIRreceiver
TheIRreceiveriswiredto
theIRhubwhichroutesthe
signaltoIRemitters
CDplayer
Andtheemitter
repeatstheIRsignal
intheotherroom.
IRReceiver
Model
P-1205
Pwr
Expansion
Global Zone
Zone
Global
Emitters
+12DC
250mA
IR
Receiver
C
V
HA NN EL
IS ION
TM
0.65”
0.35”
+V = brown wire
CAUTION: DONOT attempttocutorextendthis
wire.Doingsowillpreventtheunitfromworking.
0.4 0.2 0 0.2 0.4
0.6
0.6
0.9
1.0
0.8
0.7
d
rel
– Relative Transmission Distance
10º 20º
30º
40º
50º
60º
70º
80º
Underidealconditions,
rangesof>40feetare
possible.
DirectivityofIRSensor
TheeffectivereceivedistanceofallIRreceiverschanges
whentheIRremotecontrolisnotdirectlyinfrontoftheIR
sensor.
ThegraphbelowdescribestheperformanceoftheIRsensor
deviceusedinthisChannelVisionIRreceiver.Pleasenote
thatthegraphbelowmarksthedistanceasapercentageof
themaximumdistance.Soat0º,thedistanceis1.0(or100%)
andat30º,thedistanceis0.7(or70%)andsoon.
Actualtransmissiondistancesaredependentuponfrequency
ofremotecontrol(40kHzhasmaxrange)andluminosityof
remotecontrol(i.e.Someremotesarebrighterthanothers.)
Channel Vision Technology will repair or replace any defect in material or
workmanship which occurs during normal use of this product with new or
rebuilt parts, free of charge in the USA, for one year from the date of original
purchase. This is a no hassle warranty with no mail in warranty card needed.
This warranty does not cover damages in shipment, failures caused by other
products not supplied by Channel Vision Technology, or failures due to
accident, misuse, abuse, or alteration of the equipment. This warranty is
extended only to the original purchaser, and a purchase receipt, invoice, or
other proof of original purchase date will be required before warranty
repairs are provided.
Mail in service can be obtained during the warranty period by calling (800)
840-0288 toll free. A Return Authorization number must be obtained in
advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with this product develops
during or after the warranty period, please contact Channel Vision
Technology, your dealer or any factory-authorized service center.
Channel Vision products are not intended for use in medical, lifesaving, life
sustaining or critical environment applications. Channel Vision customers
using or selling Channel Vision products for use in such applications do so at
their own risk and agree to fully indemnify Channel Vision for any damages
resulting from such improper use or sale.
1
IR-2400
USERSGUIDE
2-Piece
IRReceiver
Drilla3/4” .hole
PushtheIRreceiverhead
throughthehole.
PushtheIRreceiverhead
throughtheholeinthe
tabletopmount.
MounttheIRreceivertothe TVoronasurfacewithinlineofsight
ofyourremotecontrol.
Removethebackingfromthetapeandattachthe
IRreceiverholsterinthedesiredlocation.
SnapIRreceiverheadintotheholster
asshown.
PushtheIRreceiverhole
mountandIRreceiverhead
backintothehole.
PushtheIRreceiverhole
mountandIRreceiverhead
backintotheholeinthetabletop
mount.
Tosecurethemount,remove
thebackingfromthefoamtape
onthebottomoftheunitand
attachthemounttoanyflatsurface.
InserttheIRreceiverhead
intotheIRreceiverholemount.
InserttheIRreceiverhead
intotheIRreceiverholemount.
MountingtheIRreceiver:Option1-Usingtheholster
MountingtheIRreceiver:Option3-UsingthetabletopmountMountingtheIRreceiver:Option2-Usingtheholemount
UsingtheIR-2400withtheP-1205
IRReceiver
Model
P-1205
Pwr
Expansion
Global
Zone
Zone
Global
Emitters
+12DC
IR
Receiver
C
V
H A N N E L
I S I O N
TM
Satradio
DVDplayer
CDplayer
Receiver
TheIR-2400canbedirectlyconnected
totheP-1205intwodifferentways:
1) Throughthe3.5mmjack
2) Throughthescrewterminalconnector
Forlargersystems,aparallelconnecting
blocksuchastheC-1201(notshown)
canbeusedtoconnectseveralIR
receiverstotheIRinputoftheP-1205.
Note:MatchtheSignal,
Ground,and+Voltage
terminalsontheIR-2400
withthecorresponding
terminalsontheP-1205
1 2
3
4
5
6
7 8 9
0
Power
  • Page 1 1
  • Page 2 2

Channel Vision IR-2400 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI