Bush Hog Dual-Fold Wheel Rakes Owner's manual

DFWR

Published 09/10 Part No. 50068783C

OPERATOR’S MANUAL

BUSH HOG

®

2501 Griffin Ave.

Selma, AL 36703

334-874-2700

www.bushhog.com

Dual Fold V-Rake

This Operator's Manual is an integral part of the safe operation of this machine and must

be maintained with the unit at all times. READ,

UNDERSTAND, and FOLLOW the Safety

and Operation Instructions contained in this manual before operating the equipment. C01-

Cover

$0.00

To the Owner/Operator/Dealer

All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded

operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has

designed this implement to be used with all its safety equipment properly attached to minimize the chance of

accidents.

BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules

of safety and common sense!

WARRANTY INFORMATION:

Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration

Form in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on the

Warranty Card and on the Warranty Form that you retain

Table of Contents

SAFETY SECTION ........................................................................................ 1-1

General Safety Instructions and Practices........................................................................................................ 1-2

Operator Safety Instructions and Practices ...................................................................................................... 1-3

Equipment Operation Safety Instructions and Practices................................................................................... 1-5

Connecting or Disconnecting Implement Safety Instructions and Practices..................................................... 1-7

Transporting Safety Instructions and Practices ................................................................................................ 1-7

Maintenance and Service Safety Instructions and Practices............................................................................ 1-9

Concluding Safety Instructions and Practices................................................................................................. 1-11

Decal Location ................................................................................................................................................ 1-12

Decal Description............................................................................................................................................ 1-14

Federal Laws and Regulations ....................................................................................................................... 1-18

INTRODUCTION SECTION........................................................................... 2-1

ASSEMBLY SECTION................................................................................... 3-1

GENERAL INSTRUCTIONS............................................................................................................................. 3-2

ASSEMBLY INSTRUCTIONS........................................................................................................................... 3-2

CENTRAL WHEEL KIT (OPTIONAL) ............................................................................................................. 3-25

LIGHT KIT INSTALLATION ............................................................................................................................ 3-29

MOUNTING REAR HYDRAULIC KIT............................................................................................................. 3-30

MOUNTING REAR HYDRAULIC KIT............................................................................................................. 3-35

KIT OPERATION ............................................................................................................................................ 3-37

OPERATION SECTION ................................................................................. 4-1

Standard Equipment and Specifications........................................................................................................... 4-3

OPERATOR REQUIREMENTS........................................................................................................................ 4-4

TRACTOR REQUIREMENTS........................................................................................................................... 4-5

ROPS and Seat Belt ......................................................................................................................................... 4-5

Tractor Safety Devices...................................................................................................................................... 4-5

Tractor Horsepower .......................................................................................................................................... 4-5

GETTING ON AND OFF THE TRACTOR ........................................................................................................ 4-6

Boarding the Tractor ......................................................................................................................................... 4-6

Dismounting the Tractor.................................................................................................................................... 4-6

STARTING THE TRACTOR ............................................................................................................................. 4-7

CONNECTING THE IMPLEMENT TO THE TRACTOR................................................................................... 4-7

Safety Chains.................................................................................................................................................. 4-10

Transport Arms ............................................................................................................................................... 4-10

CENTRAL WHEEL RAKE (Standard Kit)........................................................................................................ 4-14

HYDRAULICS................................................................................................................................................. 4-15

Hydraulic Rear Opening Kit ........................................................................................................................... 4-15

Hydraulic Kit (To Open One Side ONLY)....................................................................................................... 4-17

PRE-OPERATION INSPECTION AND SERVICE.......................................................................................... 4-18

Tractor Pre-Operation Inspection/Service....................................................................................................... 4-19

Rake Pre-Operation Inspection/Service.......................................................................................................... 4-19

DRIVING THE TRACTOR AND IMPLEMENT................................................................................................ 4-24

Starting the Tractor ......................................................................................................................................... 4-25

Brake and Differential Lock Setting................................................................................................................. 4-25

Driving the Tractor and Implement.................................................................................................................. 4-26

OPERATING THE TRACTOR AND IMPLEMENT.......................................................................................... 4-26

Foreign Debris Hazards.................................................................................................................................. 4-27

Bystanders/Passersby Precautions ................................................................................................................ 4-27

Shutting Down the Implement......................................................................................................................... 4-28

DISCONNECTING THE IMPLEMENT FROM THE TRACTOR...................................................................... 4-28

RAKE STORAGE............................................................................................................................................ 4-29

TRANSPORTING THE TRACTOR AND IMPLEMENT .................................................................................. 4-30

Transporting.................................................................................................................................................... 4-31

Transporting on Public Roadways .................................................................................................................. 4-31

Hauling the Tractor and Implement................................................................................................................. 4-33

TROUBLESHOOTING GUIDE ....................................................................................................................... 4-35

MAINTENANCE SECTION............................................................................ 5-1

LUBRICATION.................................................................................................................................................. 5-3

STORAGE ........................................................................................................................................................ 5-4

PROPER TORQUE FOR FASTENERS ........................................................................................................... 5-4

Safety Section 1-1

SAFETY SECTION

SAFETY

DFWR 09/10 Safety Section 1-2

SAFETY

General Safety Instructions and Practices

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to

the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and

observing certain precautions. The first section of this manual includes a list of Safety Messages that, if

followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety

Messages before assembling, operating or servicing this Implement. This equipment should only be operated

by those persons who have read the manual, who are responsible and trained, and who know how to do so

responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this

manual and on decals which are attached to the equipment. The Safety Alert Symbol means:

“ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word

are intended to warn the owner/operator of impending hazards and the degree of possible injury

faced when operating this equipment.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR

VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH

OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR

INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in

damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.

(SG-1)

Practice all usual and customary safe working precautions and above all---remember safety is

up to YOU

. Only YOU can prevent serious injury or death from unsafe practices.

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or

death may occur unless care is taken to follow the warnings and instructions stated in the

Safety Messages. Always use good common sense to avoid hazards.

(SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las

medidas de seguridad.

(SG-3)

SAFETY

DFWR 09/10 Safety Section 1-3

SAFETY

Operator Safety Instructions and Practices

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit

chemicals known to the state of California to cause cancer and birth defects or other

reproductive harm.

(SG-30)

Battery posts, terminals and related accessories contain lead and lead compounds,

chemicals known to the state of California to cause cancer, birth defects or other

reproductive harm.

(SG-31)

Never operate the Tractor or Implement until you have read and

completely understand this Manual, the Tractor Operator’s Manual, and

each of the Safety Messages found in the Manual or on the Tractor and

Implement. Learn how to stop the tractor engine suddenly in an

emergency. Never allow inexperienced or untrained personnel to

operate the Tractor or Implement without supervision. Make sure the

operator has fully read and understood the manuals prior to operation.

(SG-4)

The operator and all support personnel should wear hard hats, safety

shoes, safety glasses, and proper hearing protection at all times for

protection from injury including injury from items that may be thrown by

the equipment.

(SG-16)

PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE

PERMANENT HEARING LOSS! Tractors with or without an Implement

attached can often be noisy enough to cause permanent hearing loss.

We recommend that you always wear hearing protection if the noise in

the Operator’s position exceeds 80db. Noise over 85db over an

extended period of time will cause severe hearing loss. Noise over 90db

adjacent to the Operator over an extended period of time will cause

permanent or total hearing loss. NOTE: Hearing loss from loud noise

[from tractors, chain saws, radios, and other such sources close to the

ear] is cumulative over a lifetime without hope of natural recovery.

(SG-I7)

Always read carefully and comply fully with the manufacturer’s

instructions when handling oil, solvents, cleansers, and any other

chemical agent.

(SG-22)

SAFETY

DFWR 09/10 Safety Section 1-4

SAFETY

KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement

and possible serious injury or death.

(SG-24)

Never allow children to play on or around Tractor or Implement. Children can slip or fall off

the Equipment and be injured or killed. Children can cause the Implement to shift or fall

crushing themselves or others.

(SG-25)

NEVER use drugs or alcohol immediately before or while operating the

Tractor and Implement. Drugs and alcohol will affect an operator’s

alertness and coordination and therefore affect the operator’s ability to

operate the equipment safely. Before operating the Tractor or Implement,

an operator on prescription or over-the-counter medication must consult

a medical professional regarding any side effects of the medication that

would hinder their ability to operate the Equipment safely. NEVER

knowingly allow anyone to operate this equipment when their alertness or

coordination is impaired. Serious injury or death to the operator or others

could result if the operator is under the influence of drugs or alcohol.

(SG-27)

Prolonged operation may cause operator boredom and fatigue affecting safe operation.

Take scheduled work breaks to help prevent these potentially impaired operating

conditions. Never operate the Implement and Tractor in a fatigued or bored mental state

which impairs proper and safe operation.

(SG-32)

Use extreme caution when getting onto the Implement to perform repairs, maintenance and

when removing accumulated material. Only stand on solid flat surfaces to ensure good

footing. Use a ladder or raised stand to access high spots which cannot be reached from

ground level. Slipping and falling can cause serious injury or death.

(SG-33)

Avoid contact with hot surfaces including hydraulic oil tanks, pumps, motors, valves and

hose connections. Relieve hydraulic pressure before performing maintenance or repairs.

Use gloves and eye protection when servicing hot components. Contact with a hot surface

or fluid can cause serious injury from burns or scalding.

(SG-34)

DO NOT operate this Implement on a Tractor that is not properly maintained. Should a

mechanical or Tractor control failure occur while operating, immediately shut down the

Tractor and perform repairs before resuming operation. Serious injury and possible death

could occur from not maintaining this Implement and Tractor in good operating condition.

(SG-36)

Extreme caution should be used by the Tractor operator when operating near passersby.

Stop raking if anyone comes within 25 feet of the Implement to prevent possible passerby

injury or death from being struck from a thrown object, entanglement with the rakes, or run

over.

(SRK-01)

SAFETY

DFWR 09/10 Safety Section 1-5

SAFETY

Equipment Operation Safety Instructions and Practices

Do not back up with this implement. Backing could damage the machine or its components.

(S3PT-4)

There are obvious and hidden potential hazards in the operation of this Implement as in all

power-driven or pulled equipment. REMEMBER! This machine is often operated in rough

terrain conditions that include tall grass, weeds, gullies, holes, slopes, hidden obstructions

and the like. Serious injury or even death may occur unless care is taken to assure the

safety of the operator and bystanders in the area. Do not operate this machine with anyone

in the immediate area.

(S3PT-07)

This Implement may be wider than the Tractor. Be careful when operating or transporting

this equipment to prevent the Implement from running into or striking sign posts, guard rails,

concrete abutments or other solid objects. Such an impact could cause the Implement and

Tractor to pivot violently resulting in loss of steering control, serious injury, or even death.

Never allow the Implement to contact obstacles.

(S3PT-12)

Operate this Implement only in conditions where you have clear visibility in daylight or with

adequate artificial lighting. Never operate in darkness or foggy conditions where you

cannot clearly see at least 100 yards in front and to the sides of the tractor and implement.

Make sure that you can clearly see and identify passersby, steep slopes, ditches, drop-offs,

overhead obstructions, power lines, debris and foreign objects. If you are unable to clearly

see this type of items discontinue operating this equipment.

(S3PT-21)

Operate this Equipment only with a Tractor equipped with an approved roll-

over-protective system (ROPS). Always wear seat belts. Serious injury or

even death could result from falling off the tractor--particularly during a turnover

when the operator could be pinned under the ROPS.

(SG-7)

BEFORE leaving the tractor seat, always set the parking brake and/or set

the tractor transmission in parking gear, disengage the PTO, stop the

engine, remove the key, and wait for all moving parts to stop. Place the

tractor shift lever into a low range or parking gear to prevent the tractor

from rolling. Never dismount a Tractor that is moving or while the engine

is running. Operate the Tractor controls from the tractor seat only.

(SG-9)

Never allow children or other persons to ride on the Tractor or Implement.

Falling off can result in serious injury or death.

(SG-10)

SAFETY

DFWR 09/10 Safety Section 1-6

SAFETY

Never allow children to operate, ride on, or come close to the Tractor or

Implement. Usually, 16-17 year-old children who are mature and

responsible can operate the implement with adult supervision, if they

have read and understand the Operator’s Manuals, been trained in

proper operation of the tractor and Implement, and are physically large

enough to reach and operate the controls easily.

(SG-11)

Do not mount or dismount the Tractor while the tractor is moving. Mount

the Tractor only when the Tractor and all moving parts are completely

stopped.

(SG-12)

Start tractor only when properly seated in the Tractor seat. Starting a

tractor in gear can result in injury or death. Read the Tractor operators

manual for proper starting instructions.

(SG-13)

Do not operate this Equipment with hydraulic oil or fuel leaking. Oil

and fuel are explosive and their presence could present a hazard. Do

not check for leaks with your hand! High-pressure oil streams from

breaks in the line could penetrate the skin and cause tissue damage

including gangrene. To check for a hose leak, SHUT the unit ENGINE

OFF and remove all hydraulic pressure. Wear oil impenetrable gloves,

safety glasses and use Cardboard to check for evidence of oil leaks. If

you suspect a leak, REMOVE the HOSE and have it tested at a Dealer.

If oil does penetrate the skin, have the injury treated immediately by a

physician knowledgeable and skilled in this procedure.

(SG-15)

Never run the Tractor engine in a closed building or without adequate ventilation. The

exhaust fumes can be hazardous to your health.

(SG-23)

In case of mechanical difficulty during operation, place the transmission in the park

position, set the parking brake, shut down all power, including the PTO and the engine and

remove the key. Wait until all rotating motion has stopped before dismounting.

(SG-39)

SAFETY

DFWR 09/10 Safety Section 1-7

SAFETY

Connecting or Disconnecting Implement Safety Instructions and

Practices

Transporting Safety Instructions and Practices

Do Not operate this equipment in areas where insects such as bees may attack you and/or

cause you to lose control of the equipment. If you must enter in such areas, use a tractor

with an enclosed Cab and close the windows to prevent insects from entering. If a tractor

cab is not available, wear suitable clothing including head, face, and hand protection to

shield you from the insects. Attacking insects can cause you to lose control of the tractor,

which can result in serious injury or death to you or bystanders. Never dismount a moving

tractor.

(SG-40)

Objects such as wire, cable, rope, and chain can become entangled in the

rotating parts of the raking components causing mechanical damage.

Entangled items caught in the rakes can sling outward possibly injuring or

entangling the operator or passersby. Any objects that might become

entangled in a raking component should be removed from the area before

operating the rake.

(SRK-02)

Always shut the Tractor completely down, place the transmission in park, and set the

parking brake before you or anyone else attempts to connect or disconnect the Implement

and Tractor hitches.

(S3PT-15)

Never unhitch without using the Tongue Jack. The Tongue is very heavy. Attempting to lift

the Tongue without using the Tongue Jack could cause strains or other injury. Allowing the

tongue to fall suddenly and unexpectedly could result in crushing injury. Use the Tongue

Jack for lifting the Implement only. Overloading the Tongue Jack can cause failure with

possible serious bodily injury or even death.

(STI-04)

Be particularly careful when transporting the Implement with the Tractor. Turn curves or go

up hills only at a low speed and using a gradual steering angle. Rear mounted implements

move the center of gravity to the rear and remove weight from the front wheels. Make

certain, by adding front ballast, that at least 20% of the tractor’s weight is on the front wheels

to prevent rearing up, loss of steering control or Tractor tip-over. Slow down on rough or

uneven surfaces to prevent loss of steering control which could result in property damage

or possible injury. Do not transport unless 3-Point lift lever is fully raised and in the latched

transport position. Dropping implement in transport can cause serious damage to the

tractor and/or Implement and possibly cause the operator or others to be injured or killed.

(S3PT-02)

SAFETY

DFWR 09/10 Safety Section 1-8

SAFETY

Allow sufficient clearance for the Implement to swing outward while turning. Implements

carried behind the Tractor will swing outside the tire path when making turns. Contacting a

solid object while turning will cause equipment damage and possible injury.

(S3PT-20)

Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in

such a way as to be clearly visible and legible. When transporting the

Equipment use the Tractor flashing warning lights and follow all local

traffic regulations.

(SG-6)

Transport only at speeds where you can maintain control of the

equipment. Serious accidents and injuries can result from operating this

equipment at high speeds. Understand the Tractor and Implement and

how it handles before transporting on streets and highways. Make sure the Tractor steering

and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for

you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly

to determine the stopping characteristics of the Tractor and Implement. As you increase

the speed of the Tractor the stopping distance increases. Determine the maximum

transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after

you determine that the equipment can be operated at a higher speed. Use extreme care

and reduce your speed when turning sharply to prevent the tractor and implement from

turning over. Determine the maximum turning speed for you and this equipment before

operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control

the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes

or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance

increases: use extreme care and reduce your speed. When operating in traffic always use

the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you

and watch out for the other guy.

(SG-19)

Be particularly careful when transporting the Implement using the tractor. Turn curves or

go up or down hills only at a low speed and at a gradual steering angle. Make certain that

at least 20% of the tractor’s weight is on the front wheels to maintain safe steerage. Slow

down on rough or uneven surfaces.

(STI-01)

SAFETY

DFWR 09/10 Safety Section 1-9

SAFETY

Maintenance and Service Safety Instructions and Practices

Only tow the Implement behind a properly sized and equipped Tractor

which exceeds the weight of the Implement by at least 20%. DO NOT

tow the Implement behind a truck or other type of vehicle. Never tow the

Implement and another Implement connected in tandem. Never tow the

Implement at speeds over 20 MPH.

(STI-06)

Secure the Implement for transport before traveling on public roads. For pull-type

Implements, secure the center axle using cylinder stops or transport pin and properly attach

a safety chain between the Implement and Tractor. Secure wings in upright position on

folding Implements using wing transport locks.

(STI-7)

Your driving vision may be reduced or impaired by the tractor, cab, or implement. Before

driving on public roadways identify any limited vision areas, and make adjustments to your

operating position, mirrors, and the implement transport position so that you can clearly

see the area where you will be traveling, and any traffic that may approach you. Failure to

maintain adequate vision of the public roadway and traffic can result in serious injury or

even death.

(STI-10)

Make sure the PTO shield, integral driveline shields, and input shields

are installed when using PTO-driven equipment. Always replace any

shield if it is damaged or missing.

(S3PT-8)

Relieve hydraulic pressure prior to doing any maintenance or repair work

on the Implement. Place the Implement on the ground or securely

blocked up, disengage the PTO, and turn off the tractor engine. Push

and pull the Remote Cylinder lever in and out several times prior to

starting any maintenance or repair work.

(S3PT-09)

Always disconnect the main PTO Driveline from the Tractor before performing service on

the Implement. Never work on the Implement with the tractor PTO driveline connected and

running. Rotating Parts, Blades or Drivelines could turn without warning and cause

immediate entanglement, injury or death.

(S3PT-11)

Always maintain the safety signs in good readable condition. If the safety signs are missing,

damaged, or unreadable, obtain and install replacement safety signs immediately.

(SG-5)

Do not modify or alter this Implement. Do not permit anyone to modify or alter this

Implement, any of its components or any Implement function.

(SG-8)

SAFETY

DFWR 09/10 Safety Section 1-10

SAFETY

Never work under the Implement, the framework, or any lifted

component unless the Implement is securely supported or blocked up

to prevent sudden or inadvertent falling which could cause serious

injury or even death.

(SG-14)

Never attempt to lubricate, adjust, or remove material from the Implement while it is in

motion or while tractor engine is running.

(SG-20)

Periodically inspect all moving parts for wear and replace when

necessary with authorized service parts. Look for loose fasteners, worn

or broken parts, and leaky or loose fittings. Make sure all pins have

cotter pins and washers. Serious injury may occur from not maintaining

this machine in good working order.

(SG-21)

Perform service, repairs and lubrication according to the maintenance section. Ensure the

unit is properly lubricated as specified in the lubrication schedule and all bolts and nuts are

properly torqued. Failure to properly service, repair and maintain this Implement in good

operating condition could cause component failure and possible serious injury or even

death.

(SG-35)

Use caution and wear protective gloves when handling sharp objects such as blades,

knives, and other cutting edges. Be alert to worn component surfaces which have sharp

edges. Sharp surfaces can inflict severe laceration injuries if proper hand protection is not

worn.

(SG-37)

PARTS INFORMATION

Bush Hog products are designed utilizing specifically matched system components to ensure optimum

equipment performance. These parts are made and tested to Bush Hog specifications. Non-genuine "will fit"

parts do not consistently meet these specifications. The use of “will fit” parts may reduce equipment

performance, void warranties, and present a safety hazard. Use genuine Bush Hog parts for economy and

safety.

(SPBH-2)

SEE YOUR BUSH HOG DEALER

SAFETY

DFWR 09/10 Safety Section 1-11

SAFETY

Concluding Safety Instructions and Practices

DFWR1225

DFWR1448 DFWR1631 DFWR18

ITEM PART NO. QTY QTY QTY TYPE DESCRIPTION

1. 00725746 1 1 1 PELIGRO Spanish Translation

2. 999001 1 1 1 WARNING Multi-Hazard

3. 00760657 1 1 1 IMPORTANT Genuine Bush Hog Parts

4. 00763977 1 1 1 INFORMATION Notice to Owner

5. 50058089 2 2 2 LOGO Bush Hog Logo

6. 5W119 1 1 1 WARNING Speed Restriction

7. 03200347 1 1 1 REFLCTR SMV Sign

8. 02962765 10 12 14 DANGER Multi Hazard - Pinch Points

9. 02965262 5 5 5 WARNING Oil Leak

10. 3668308 2 2 2 WARNING Transport Lock

11. 1458392 4 4 4 REFLECT Red Reflector

12. 1458393 6 6 6 REFLECT Yellow Reflector

13. 1458398 2 2 2 REFLECT Orange Reflector

14. 999200 1 1 1 WARNING Multi-Hazard

15. 50068845 2 - - DECAL Model DFWR

16. 2458315 2 2 2 WARNING Stored Energy

17. NFS 1 1 1 SER PLT Serial Plate

18. 00776031 1 1 1 CANISTER Manual Storage

19. 50068783C 1 1 1 MANUAL Operator’s Manual

20. 10058000 3 3 3 Bolt

21. 00024100 3 3 3 Flatwasher

22. 02959924 3 3 3 Locknut

* Furnished by tractor manufacturer.

In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment,

hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper

training of personnel involved in the operation, transport, maintenance, and storage of the machine. Refer

also to Safety Messages and operation instruction in each of the appropriate sections of the Tractor and

Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment.

(SG-18)

SAFETY

DFWR 09/10 Safety Section 1-12

SAFETY

Decal Location

NOTE: Bush Hog supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in

shipping, use, or reconditioning. Bush Hog cares about the safety of its customers, operators, and bystanders, and will replace the

safety decals on this product in the field, free of charge (Some shipping and handling charges may apply). Contact your Bush Hog

dealer to order replacement decals.

SAFETY

DFWR 09/10 Safety Section 1-13

SAFETY

Decal Location

NOTE: Bush Hog supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in

shipping, use, or reconditioning. Bush Hog cares about the safety of its customers, operators, and bystanders, and will replace the

safety decals on this product in the field, free of charge (Some shipping and handling charges may apply). Contact your Bush Hog

dealer to order replacement decals.

SAFETY

DFWR 09/10 Safety Section 1-14

SAFETY

Decal Description

Peligro Translation, If you do not know how to read

English, please find someone who knows how to

read English.

P/N 00725746

WARNING! Tractor rearing

P/N 999001

For safety and to guarantee optimum product

reliability always use genuine Bush Hog

replacement parts.

P/N 00786980

Operator's Manual (with repair parts) and warranty

was attached to this implement during final

inspection.

P/N 00763977

SAFETY

DFWR 09/10 Safety Section 1-15

SAFETY

P/N 50058089

Logo Product Name: Bush Hog (11” x 2.42”)

WARNING! Speed Restriction.

P/N 5W119

Slow Moving Vehicle Decal. Keep SMV reflector

clean and visible. DO NOT transport or operate

without the SMV.

P/N 03200347

DANGER! Crushing and Pinch Points.

Moving machinery parts can pinch or crush or fall-

which may cause injury or death.

P/N 02962765

SAFETY

DFWR 09/10 Safety Section 1-16

SAFETY

WARNING! Failure to INSPECT and REPAIR or

REPLACE Hoses may allow worn Hoses to rupture

SUDDENLY and VIOLENTLY with resulting serious

BODILY INJURY from SCALDING or FIRE with

resulting BURN INJURY or DEATH.

P/N 02965262

WARNING! Transport.

P/N 3668308

Red Reflector. Keep reflectors clean and visible.

P/N 1458392

Amber Reflector. Keep reflectors clean and visible.

P/N 1458393

Page is loading ...

Bush Hog Dual-Fold Wheel Rakes Owner's manual

Bush Hog Dual-Fold Wheel Rakes Owner's manual

Related papers

Other documents