Page is loading ...
COLDHOT
Exposed Wall Mount
Sink Faucet with Top Brace
ROUGHING-IN DIMENSIONS
M965443 REV. 1.4 (12/14)
Certified to comply with ANSI A112.18.1M
8344.212
with M955069
Vacuum Breaker
ROUGH-IN
1
Prepare water supply lines per "Roughing-in
Dimensions". Install 1/2" NPT. SUPPLY NIPPLES.
Installation
Instructions
Sealing TapeAdjustable Wrench Phillips Screwdriver
Channel Locks
RECOMMENDED TOOLS
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
2-1/2"
(63mm)
1-1/2"
(38mm)
3/4" HOSE
TREADS
8"
(203mm)
10-1/4"
(259mm)
7"
(178mm)
BACKFLOW
PREVENTER
12-11/16"
(323mm)
1/2 N.P.T.
FEMALE
2-3/8" DIA.
(60mm)
2-3/4"- 3-1/8"
(70-79mm)
8-1/2" REF.
(216mm)
WALL
SUPPORT
FINISHED WALL
1/2 NPT. FEMALE THREADS
FINISHED WALL
1/2 NPT. SUPPLY NIPPLE
1/2 to 3/4
1-1/4 DIA. OPENING
ECCENTRIC
3/8" Socket Wrench
This atmospheric vacuum breaker shall not be subjected to
continuous pressure for more than twelve (12) hours.
A. The device shall be installed in accordance with the
requirements of the local plumbing code.
B. The device shall not be installed where the venting of
water from the device during its normal functioning
causes damage.
C. The device shall be installed downstream of the last valve.
M965443 REV. 1.4 (12/14)
If spout drips, operate handles several
times from OFF to ON position.
Do not force - handles turn only 90°.
ATTACH SPOUT BRACE
Fig. A
Fig. B
3
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
3
1
Attach SPOUT BRACE ASSEMBLY (1) to SPOUT HINGE (2). Align MOUNTING
PLATE (3) against the wall and mark the two mounting holes.
IF WALL MOUNTING PLATE (3) is not fastened to a wall support within
the wall, use wall anchors with MOUNTING SCREWS.
2
Turn HANDLES TO OFF POSITION.
Slowly turn water supplies on and
check all connections for leaks.
Operate HANDLES to flush water
lines thoroughly.
Turn HANDLES to OFF position.
TEST FAUCET
4
OFF
ON
1
90˚
2
2
FINISH INSTALLATION
2
1
1
3
4
6
5
8"
Thread ESCUTCHEONS (1) fully onto INLET SHANK ECCENTRICS (2). Fig. A
Apply Sealing Tape to threads of SUPPLY NIPPLES (3). Fig. A
Thread INLET SHANK ECCENTRICS (2) onto SUPPLY NIPPLES (3)
with a 3/8" socket wrench. Fig. A
Distance between INLET SHANKS (3) outlets must be 8" to align with
the FAUCET inlets. Fig. B
Insert RUBBER WASHERS (4) into COUPLING NUTS (5). Fig. B
Attach COUPLING NUTS (5) to VALVE (6). Tighten both
COUPLING NUTS (5) firmly. Fig. B
Thread ESCUTCHEONS (1) tight
against finished wall. Fig. B
3/8" SOCKET
WRENCH
SEALING TAPE
M965443 REV. 1.4 (12/14)
MODEL NUMBER
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names li sted herein are trademarks of American St andard Inc.
© AS America, I nc. 2013
HOT LINE FOR HELP
M964359-YYY0A
SPOUT BRACE
M964362-YYY0A
LEVER HANDLE
M964363-YYY0A
BONNET NUT
M964367H-0070A
CARTRIDGE (HOT)
M964367C-0070A
CARTRIDGE (COLD)
Exposed Wall Mount
Sink Faucet with Top Brace
8344.212
CHROME
ROUGH CHROME
002
004
Replace the "YYY" with
appropriate finish code
M964361-0070A
HANDLE SCREW
M964360-0070A
INDEX KIT (PAIR)
M964364-YYYOA
FEMALE ECCENTRIC
SHANK W/ESCUTCHEON
M964365-0070A
GASKET
M962952-YYY0A
VACUUM BREAKER
REPAIR KIT
/
