Message Receiver
Turning the
ADVISOR
Pager On
• Press the “On/Reset” button.
• The pager will run a 4-second power-up alert, and the “On
Indicator” will appear in the upper left corner of the dis-
play.
• The pager is ready to receive messages.
Turning th
e ADVISOR
Pager Off
• Press the “On/Reset” button until “PUSH FOR OFF” ap-
pears on the screen.
• While the words are displayed, press the “Function” button
to turn off.
Receiving Messages
• To alert you of an incoming message, your pager will beep
or vibrate, the red light will flash, and the incoming-mes-
sage symbol will be displayed for 12 seconds. Press any
button to cancel the alert.
• Press the “Read” button. Your message will be displayed
for 8 seconds.
• The message will then be stored automatically with the
time and dates received.
** A flashing “ON” symbol indicates a message has been
received, but not read. The pager will beep once every
two minutes until the message is read.
Reading Messages
• Press the “Read” button.
• An arrow on the display shows the locations of messages
that are in memory. Unread messages are indicated by
flashing arrows. The cursor is automatically positioned to
the message received most recently.
• Use the left and right arrow buttons to select the message
you wish to read.
• Press the “Read” button. Your message will be displayed,
preceded by the memory location.
• The pager will automatically scroll through messages for
you at a rate of 4 seconds per screen. To manually scroll,
press the “Read” button a second time. Subsequent presses
of the “Read” buton will take you through the message
screens.
• Messages can be read one line at a time by using the up
and down arrow buttons to scroll through it.
Backlighting
To activate the backlight press the function button and hold
it for one second. The backlight will turn on. To turn off the
backlight, you can hold down the function button again for
one second, or let the pager time out when you are through
with the desired function.
Function Menu
To activate the function menu, use the following procedure:
• Press the Function Button once.
• Choose a particular function by using the left or right direc-
tional control arrow until the desired function indicator is
flashing.
• Press the Function Button again to activate
ADVISOR
On Indicator
On/Reset Button
Alert Lamp
Function/Backlight Button
Directional Control Arrows
Read Button
©©©À
É Ã » á Õ ë ¶ «
Message Indicators
Alerts
Clock
Alarm
Speaker
Delete
Personal
Message
File
Lock
Speaker Function
This function is used to set the
ADVISOR pager to either the
audible or the vibrate mode of operation. To change the speak-
er function:
• Select the speaker symbol in the function menu and press
the “Function” button.
• The pager will vibrate or chirp depending on which mode
you have selected.
** If the pager is in the audible mode, a speaker symbol will
appear in the lower left corner of the screen.
Clock Function
• Select the clock symbol on the menu, then press the “Func-
tion” button.
• The screen will display the time, day, month, and year. Use
the left and right arrow buttons to select the field to change,
and use the up and down arrow buttons to to change the
values.
• Press the “Function” button to save the changes you have
made.
Alarm Function
• Select the alarm symbol on the menu, then press the Func-
tion" button.
• The screen will display the time and the alarm on/off sym-
bol. Use the left and right arrow buttons to select the field
to change, and use the up and down arrow buttons to to
change the values and to turn the alarm on or off
• Press the “Function” button to save the changes you have
made. If the alarm has been activated, the alarm on symbol
will appear on the screen.
Protecting Messages
Up to ten messages can be “locked” in memory to prevent
them from being replaced when the memory is full.
• Press the “Read” button.
• Select the message you wish to be locked by using the left
or right directional arrows.
• Press the “Function” button to display the menu at the bot-
tom of the screen. Use the left or right directional arrows to
select the lock symbol, then press the “Function” button
again to lock the message.
• The lock symbol will appear in the message location in
place of the arrows and at the beginning of the message
when it is being read.
• To unlock a message, select the lock symbol in the function
menu, and press the “Function” button.
This document was created with FrameMaker 4.0.4
