Minka Lavery 3307-84 Installation guide

Type
Installation guide

Minka Lavery 3307-84 is a versatile lighting fixture that combines classic design with modern functionality. It features a cloth shade that adds a touch of elegance to any room. The fixture is easy to install and can be used in a variety of settings, including bedrooms, living rooms, and dining rooms. The fixture is compatible with incandescent or LED bulbs, allowing you to customize the lighting to your preference.

Minka Lavery 3307-84 is a versatile lighting fixture that combines classic design with modern functionality. It features a cloth shade that adds a touch of elegance to any room. The fixture is easy to install and can be used in a variety of settings, including bedrooms, living rooms, and dining rooms. The fixture is compatible with incandescent or LED bulbs, allowing you to customize the lighting to your preference.

INSTALLATION INSTRUCTIONS
Item#3307-84 (New. 12/14/2015)
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
LA-2512E
HANGING THE FIXTURE (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker.
If necessary, remove old fixture, including mounting
hardware.
2. Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
3. Secure socket assembly (G) into the nipple (F) of
fixture body (H).
4.
A
lign cloth shade (K) with screw (E) by using cap
nut (L).
5. Attach the mounting plate (A) to the junction box
with mounting screws (B) (Size: #8-32N*L0.5”). The
side of the mounting plate with “GND” marked on it
and two convex points must face out.
CONNECTING THE WIRES (Fig. 2)
6.
A
t this point, connect the electrical wire as shown in
figure 2, making sure that all wire connectors are
secured. If your outlet has a ground wire (green or
bare copper), connect the fixtures ground wire to it.
Otherwise, connect the fixture ground wire directly
to the circular strap using the green screw provided.
COMPLETING THE INSTALLATION (Fig. 1)
7. Install the light bulbs (not included) in accordance
with fixture specifications. (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!). (NE PAS
DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
8. Thread the nipple (I) to socket assembly (G) and
tighten it with hex nut (J).
9. Align canopy (D) over the mounting plate (A) and
secure with screws (C).
10.
A
lign spacer (M) followed by glass shield (N) onto
nipple (I) to adjust spacer (M) to make glass (N) flat
with cloth shade (K) and secure with finial (O).
Your installation is now complete. Return power to the
junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
FIXTURE
WIRES
Black or
Smooth
H
O
U
S
E
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
H
O
U
S
E
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
H
O
U
S
E
WIRES
Green
(Ground)
Set# A-021-118DB
-Mounting Plate
-Ground Screw
-Mounting Screw*2
H
A
B
C
D
K
L
M
N
O
F
E
G
I
J
  • Page 1 1

Minka Lavery 3307-84 Installation guide

Type
Installation guide

Minka Lavery 3307-84 is a versatile lighting fixture that combines classic design with modern functionality. It features a cloth shade that adds a touch of elegance to any room. The fixture is easy to install and can be used in a variety of settings, including bedrooms, living rooms, and dining rooms. The fixture is compatible with incandescent or LED bulbs, allowing you to customize the lighting to your preference.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI