NAD l 56 User manual

L56

DVD / Video CD / CD Player

Owner’s Manual

Manuel d’Installation

Bedienungsanleitung

Manual del Usuario

GB

F

D

E

PAUSE STOP

OPEN /

CLOSE

SKIP / SCAN

PLAY

NA

D

DVD / CD / MP3 Player L56

PAUSE STOP

OPEN /

CLOSE

SKIP / SCAN

PLAY

NA

D

DVD / CD / MP3 Player L56

GB

2

SAFETY PRECAUTIONS

Introduction

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert

the user to the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that

may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence

of important operating and maintenance (servicing) instructions in the literature accompanying

the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR

MOISTURE.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

CAUTION

This Digital Video Disc Player employs a Laser System. To ensure proper use of this product, please read this

owner’s manual carefully and retain for future reference. Should the unit require maintenance, contact an

authorized service location. (See service procedure). Use of controls, adjustments or the performance of

procedures other than those specified may result in exposure to laser radiation. To prevent direct exposure

to laser beam, do not try to open the enclosure. Visible laser radiation when the enclosure is opened.

DO NOT STARE INTO BEAM.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

INDUSTRY CANADA REQUIREMENT

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

RECORD YOUR MODEL NUMBER (Now, while you can see it)

The model and serial number of your new DVD player are located on the back of the DVD player cabinet.

For your future convenience, we suggest that you record these numbers here:

MODEL NO :

SERIAL NO.:

GB

3

TABLE OF CONTENTS

Introduction

INTRODUCTION

Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Identification of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-11

Front Panel/Display window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Preparing the Remote Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operating with the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-17

INSTALLATION

Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Connecting to an Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Connecting to Optional Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-22

Enjoying Dolby Digital (AC-3) Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Enjoying Dolby Pro Logic Surround Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Enjoying 2 Channel Digital Stereo Sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Enjoying DTS Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

BASIC OPERATION

Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-25

Various speed playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

OPERATION USING DISPLAY MENU ICONS

General Information about Display Menu Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Detailed description of each Display Menu Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

ADVANCED OPERATION

Using a title menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Using a DVD menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Changing audio soundtrack language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Changing subtitle language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Viewing from another angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Zoom Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Memorizing Settings for Viewed DVDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Program Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

INITIAL SETTINGS

Common procedures of initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Selecting disc Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Selecting rating level and password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38-39

Selecting TV Aspect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Selecting Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Selecting the TV Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Selecting Digital Audio Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

REFERENCE

Disc Requirements/Copyright Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Before Calling Service Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

GB

4

IMPORTANT SAFETY INSTRUCTIONS

Introduction

CAUTION

PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL

AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This set has been designed and manufactured to assure personal safety. Improper use can result in electric

shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following

procedures for installation, use and servicing.

This unit is fully transistorized and does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1 Read owner’s manual - After unpacking this product, read the owner’s manual carefully and follow

all the operating and other instructions.

2 Power Sources - This product should be operated only from the type of power source indicated on

the marking label. If you are not sure of the type of power supply in your home, consult your product

dealer or local power company. For products intended to operate from battery power or other sources,

refer to the operating instructions.

3 Grounding or Polarization - This product is equipped with a polarized alternating current line plug

(a plug having one blade wider than the other). This plug will fit into the power outlet only one way.

This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug.

If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat

the safety purpose of the polarized plug.

4 Heat - The product should be situated away from heat sources such as radiators, heat registers, stoves

or other products (including amplifiers) that produce heat.

5 Water and Moisture - Do not use this product near water-for example, near a bath tub, wash bowl,

kitchen sink. or laundry tub; in a wet basement; or near a swimming pool and the like.

6 Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or

aerosol cleaners. Use a damp cloth for cleaning.

7 Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked

on or pinched by items placed upon or against them, playing particular attention to cords at plugs,

convenience receptacles, and the point where they exit from the product.

8 Overloading - Do not overload wall outlets, extension cords or integral convenience receptacles as this

can result in a risk of fire or electric shock.

9 Lightning - For added protection of this product during storms, or when it is left unattended and

unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product

due to lightning and power-line surges.

10 Object and Liquid Entry - Never push objects of any kind into this product through openings as they

may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never

spill liquid of any kind on the product.

11 Attachments - Do not use attachments not recommended by the product manufacturer as they may

cause hazards.

GB

5

IMPORTANT SAFETY INSTRUCTIONS

Introduction

12 Accessories - Do not place this product on an unstable cart, stand, tripod, bracket or table. The

product may fall, causing serious injury to a child or adult and serious damage to the product. Use

only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the

product. Any mounting of the product should follow the manufacturer’s instructions, and should use

a mounting accessory recommended by the manufacturer. A product and cart combination should

be moved with care. Quick stops, excessive force and uneven surfaces may cause the product and

cart combination to overturn.

13 Disc Tray - Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal

injury.

14 Burden - Do not place a heavy object on top of the product. The object may fall, causing serious

personal injury and serious damage to the product.

15 Connecting - When you connect the product to other equipment, turn off the power and unplug all

of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious

personal injury. Read the owner’s manual of the other equipment carefully and follow the

instructions when making any connections.

16 Sound Volume - Reduce the volume to the minimum level before you turn on the product.

Otherwise, sudden high volume sound may cause hearing or speaker damage.

17 Sound Distortion - Do not allow the product to output distorted sound for a longtime. It may

cause speaker overheating and fire.

18 Headphones - When you use headphones, keep the volume at a moderate level. If you use the

headphones continuously with high volume sound, it may cause hearing damage.

19 Laser Beam - Do not look into the opening of the disc tray or ventilation opening of the product to

see the source of the laser beam. It may cause sight damage.

20 Disc - Do not use a cracked, deformed or repaired disc. These discs are easily broken and may cause

serious personal injury and product malfunction.

21 Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to

qualified service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operating instructions as an improper adjustment of other controls

may result in damage and will often require extensive work by a qualified technician to restore the

product to its normal operation.

• If the product has been dropped or damaged in any way.

• When the product exhibits a distinct change in performance (This indicates a need for service).

22 Servicing - Do not attempt to service this product yourself as opening or removing covers may

expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

23 Replacement parts - When replacement parts are required, be sure the service technician has used

replacement parts specified by the manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

24 Safety Check - Upon completion of any service or repairs to this product, ask the service technician

to perform safety checks to determine that the product is in proper operating condition.

GB

6

PRECAUTIONS

Introduction

NOTES ON HANDLING

• When shipping the DVD player, always use the original shipping carton and packing materials. For

maximum protection, repack the unit as it was originally packed at the factory.

• Do not use volatile liquids, such as insect spray, near the DVD player. Do not leave rubber or plastic

products in contact with the DVD player for a long time. They will leave marks on the finish.

• The top and rear panels of the DVD player may become warm after a long period of use. This is normal

and not a malfunction.

• When the DVD player is not in use, be sure to remove the disc and turn off the power.

• If you do not use the DVD player for a long period, the unit may not function properly in the future.

Turn on and use the DVD player occasionally.

NOTES ON LOCATING

• When you place this DVD player near a TV, radio, or VCR, the playback picture may become poor and

the sound may be distorted. In this case, move the DVD player away from the TV, radio, or VCR.

NOTES ON CLEANING

Use a soft, dry cloth for cleaning.

• For stubborn dirt, soak the cloth in a weak detergent solution, wring well and wipe. Use a dry cloth to

wipe it dry. Do not use any type of solvent, such as thinner and benzine, as they may damage the

surface of the DVD player.

• If you use a chemical saturated cloth to clean the unit, follow that product’s instructions.

WARNING

Cleaning and adjustment of lenses and/or other components of playback mechanism should be performed

by a qualified service technician.

TO OBTAIN A CLEAR PICTURE

The DVD player is a high technology, precision device. If the optical pick-up lens and disc drive parts are

dirty or worn down, the picture quality becomes poor. To obtain a clear picture, we recommend regular

inspection and maintenance (cleaning or parts replacement) every 1,000 hours of use depending on the

operating environment. For details, contact your nearest dealer.

NOTES ON MOISTURE CONDENSATION

Moisture condensation damages the DVD player. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops

of water form on the outside of the glass. In the same way, moisture may condense on the opti-cal pick-

up lens inside this unit, one of the most crucial internal parts of the DVD player.

Moisture condensation occurs during the following cases.

• When you bring the DVD player directly from a cold place to a warm place.

• When you use the DVD player in a room where you just turned on the heater, or a place where the

cold wind from the air conditioner directly hits the unit.

• In summer, when you use the DVD player in a hot and humid place just after you move the unit from

an air conditioned room.

• When you use the DVD player in a humid place.

• Do not use the DVD player when moisture condensation may occur. If you use the DVD player in such

a situation, it may damage discs and internal parts. Remove the disc, connect the power cord of the

DVD player to the wall outlet, turn on the DVD player and leave it “ON” for two or three hours. After

two or three hours, the DVD player will have warmed up and evaporated any moisture. Keep the DVD

player connected to the wall outlet and moisture condensation will seldom occur.

GB

7

Introduction

This section shows you how to handle, clean and store discs.

ON HANDLING DISCS

• Do not touch the playback side of the disc.

• Do not attach paper or tape to discs.

ON CLEANING DISCS

• Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center

outward with a soft cloth. Always keep the disc clean.

• If you cannot wipe off the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft

cloth and finish with a dry cloth. Do not use any type of solvents such as thinner, benzine, commercially

available cleaners or anti-static spray for vinyl LPs. They may damage the disc.

ON STORING DISCS

• Do not store discs in a place subject to direct sunlight or near heat sources.

• Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier.

• Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause

warping.

ABOUT THIS OWNER’S MANUAL

• This owner’s manual explains the basic instructions of this DVD player.

• Some DVD video discs have functions that may not be explained in this owner’s manual. Therefore,

some instructions may differ from this owner’s manual, and there may be extra instructions. In this case,

follow the instructions displayed on the TV screen or package.

• “ “ may appear on the TV screen during operation. This icon means the function explained in this

owner’s manual is not available on that specific DVD video disc.

NOTES ON DISCS

GB

8

IDENTIFICATION OF CONTROLS

Introduction

FRONT PANEL

DISPLAY WINDOW

POWER indicator (Standby mode: Blue color)

Disc tray

PLAY button

PAUSE/STEP button

STOP button

SKIP/SCAN buttons

OPEN/CLOSE button

DISPLAY WINDOW

REMOTE SENSOR

POWER button

OPERATING STATUS indicator

VCD indicator

CD indicator

DVD indicator

PROGRAM indicator

Repeat playback mode indicators

TOTAL PLAYING TIME /

ELAPSED TIME indicator

CHP/TRK NUMBER indicator

TITLE NUMBER indicator

ANGLE ICON indicator

DVD / CD / MP3 Player L 56

GB

9

IDENTIFICATION OF CONTROLS

Introduction

REAR PANEL

EUROPEAN VERSION

S-VIDEO OUT jack

COMPOSITE VIDEO OUT jack

AUDIO MIXED OUT jacks

EURO AV-TV-VCR OUT jack

OPTICAL DIGITAL AUDIO OUT jack

DIGITAL AUDIO OUT jacks (COAXIAL)

POWER CORD

Connect to an AC 230V,

50Hz outlet only

OPTICAL DIGITAL AUDIO OUT JACK

Remove the dust protection cap from the connector and connect the optical digital cable (not supplied) firmly so that the configurations of both the

cable and the connector match. Keep the dust protection cap and always reattach the cap when not using the connector to protect against dust.

Dust protection cap

GB

10

IDENTIFICATION OF CONTROLS

Introduction

REMOTE CONTROL

You will find instructions for each of the remote control functions in the appropriate sections of this instruction manual.

(Remote control unit is included in L76 AV Surround Receiver)

TITLE BUTTON

Use the TITLE button to display

the title screen included on DVD

video discs. To operate a menu

screen, follow the instructions in

“Using a Title Menu” (page 23).

DIRECTIONAL ARROW

BUTTONS

(up, down, left, right) for use in

highlighting a selection on a

DISPLAY menu screen, TITLE and

MENU screen.

MENU BUTTON

Use the MENU button to display

the menu screen included on DVD

video discs. To operate a menu

screen, follow the instructions in

“Using a DVD Menu” (page 23).

•Top section features

ON/OFF, MACRO and

eight DEVICE SELECTOR

keys

• Upper middle section has

AV PRESET, SPEAKER and

number keys 0 to 10+

• Middle section with

channel, volume, DVD

navigation and surround-

sound keys

• Lower middle section

with transport control

keys

• Bottom section with

CHANNEL VOLUME

trimming keys

GB

11

IDENTIFICATION OF CONTROLS

Introduction

PREPARING THE REMOTE CONTROL

Insert the batteries into the remote control so you can use it to operate the DVD player.

1 Open the battery cover.

2 Insert batteries (AAA size). Make sure to match the + and - on the batteries to the marks inside the

battery compartment.

3 Close the cover.

NOTES ON BATTERIES

• Improper use of batteries may cause battery leakage and corrosion.

• To operate the remote control correctly, follow the instructions.

• Do not insert the batteries into the remote control in the wrong direction.

• Do not charge, heat, open or short-circuit the batteries. Do not throw the batteries into fire.

• Do not leave dead or exhausted batteries in the remote control.

• Do not use different types of batteries together, or mix old and new batteries.

• If you do not use the remote control for a long period of time, remove the batteries to avoid possible

damage from battery corrosion.

• If the remote control does not function correctly or if the operating range becomes reduced, replace

all batteries with new ones.

• If battery leakage occurs, wipe the battery liquid from the battery compartment, then insert new

batteries.

• The batteries should last about one year with normal use.

OPERATING WITH THE REMOTE CONTROL

This section shows you how to use the remote control.

Point the remote control at the remote sensor and press the buttons.

Distance: About 23 ft (7 m) from the front of the remote sensor

Angle: About 30° in each direction of the front of the remote sensor

• Do not expose the remote sensor of the DVD player to a strong light source such as direct sunlight or

illumination. If you do so, you may not be able to operate the DVD player with the remote control.

NOTES ON THE REMOTE CONTROL

• Direct the remote control at the remote sensor of the DVD player.

• Do not drop or give the remote control a shock.

• Do not leave the remote control near extremely hot or humid place.

• Do not spill water or put anything wet on the remote control.

• Do not open the remote control.

PLACE BATTERIES INTO OPENING.

INSURE THE CORRECT FITTING

IS OBSERVED

PRESS IN AND LIFT TAB TO REMOVE BATTERY COVER

OUT OF RECESS

PRESS BATTERY COVER INTO

PLACE UNTIL IT ‘CLICKS’ CLOSED

REPLACE BATTERY COVER BY ALIGNING

AND INSERTING THE TWO TABS INTO THE

HOLES.

SPECIFICATIONS

• Controls up to 8 devices

• 44 function keys

• Learns up to 352 commands

• Records up to 44 macros with a maximum of 64 commands each

• Configurable punch-through

• Key illumination with programmable timeout

•Upgradable

• Contains pre-programmed library of NAD remote codes for the L56.

The NAD HTR L76 is ready to operate the L56 DVD player right out of the box, but it is really eight remotes

in one. Each of the 8 Device Selector keys at the top of the handset can call up a new “page” of remote-

control codes to be transmitted by the remaining 44 keys. You may “teach” codes from any infrared-

remote-controlled component, regardless of brand, to any or all of these. Obviously, the most logical

system is that you teach the codes from your DVD player to the “DVD” Device Selector “page,” your

television’s codes to the “TV” “page,” and so on, but there is no required scheme: You may load any

commands to any key on any page (see “Learning Codes From Other Remotes,” below).

The HTR L76 is already preprogrammed with a full complement of commands for the L76 receiver on its

“AMP”, “TUNER” and “DVD” Device Selector page, and as well as with library commands to operate

most NAD-brand DVD, CD, or TAPE components on the corresponding Device Selector “pages.” These

default commands are permanent: Even if you teach the HTR L76 new commands to take their place, the

underlying library commands remain in place and can easily be recalled should you add an NAD

component to your system later (see “Delete Mode,” below).

NOTE

For use with the L56, it should not be necessary to re-program any keys on the HTR L76 “AMP” and

L56 “DVD” page. However, in order for the HTR L76 to control your specific NAD-brand components you

may need to load one or more different code-libraries; see “Loading Code Libraries,” below.

CONTROLLING THE L56

The HTR L76 is divided into two main sections. Eight Device Selector keys at the top-“AMP”, “DVD,”

“TV,” and so on-set the handset’s remaining keys to a “page” of commands to control a particular

component. A Device Select key determines only what component the HTR L76 will command; it does

not perform any function on the receiver. All of the remaining keys are function keys that can “learn”

control codes from virtually any infrared remote controller, allowing you to teach the codes of your

equipment, regardless of brand, to the HTR L76.

However, the HTR L76 is already preprogrammed to operate the L56. All of the function keys on the

“AMP”, “TUNER” and “DVD” Device Selector “page” perform L76 functions. (The HTR L76 can also

command many other NAD components, from its “CD” and “TAPE” pages.)

It is important to note that certain HTR L76 keys perform different functions depending on the selected

Device Selector “page.” The colour of the Device Selector key-labelling corresponds to the labelling of the

function keys. Most centrally, the orange “AMP” Device Selector “page” corresponds to the orange

input-select labelling adjacent to the numeric keys: When the HTR L76’s “AMP” Device Selector page is

active, these keys select the receiver inputs. Similarly, the red “DVD” Device Selector “page” corresponds

to several red labels, the green “TV” page to green labels, and so on.

IDENTIFICATION OF CONTROLS

12

GB

LEARNING CODES FROM OTHER REMOTES

Begin by positioning the HTR L76 “nose-to-nose” with the source remote so the two devices’ infrared

windows are about 2 inches apart.

• Enter Learning Mode: On the HTR L76, simultaneously press-and-hold for 3 seconds both a Device

Selector key and the “OPEN/CLOSE” key (just below the “DISP” key), until the Learn LED at

the centre of the HTR L76 turns steady green.

•Press the HTR L76’s function key you wish to teach a command; the Learn LED will turn amber.

•Press-and-hold the function key on the source remote: The HTR L76’s Learn LED will flicker amber

for a second or two, then turn solid green. The command is learned.

•Press the HTR L76’s Device Selector key again to exit the learning mode.

If the Learn LED does not flicker amber you may need to vary the distance between the remotes. If the

Learn LED turns red rather than green, that particular command of that source remote command could

not be learned.

CANCEL OPERATION

You can cancel configuring a key, by pressing the active Device Selector key before the learn process is

complete; the Learn LED will turn red.

Example: Learning “VCR Pause”:

Position the HTR L76 and your VCR player’s remote as described above.

• On the HTR L76, simultaneously press-and-hold “VCR” and ; the Learn LED turns steady

green.

•Press the HTR L76’s (pause) key; the Learn LED turns amber.

•Press-and-hold the VCR player’s remote’s pause key; the HTR L76’s Learn LED flickers amber and

then turns solid green. The command is learned.

•Press “VCR” again to exit the learning mode.

PUNCH-THROUGH

The HTR L76’s “punch-through” function allows you to retain a function key from one Device Select

“page” on another, so that, for example, the AMP “SURR MODE” function might still control the L76

when the DVD Device Selector page is active

NOTE

The HTR L76’s “VOL” and “MUTE” keys are pre-programmed as “punched-through” for all Device

Select pages: “VOL” will operate the L76’s master-volume regardless of the currently selected device.

The “SURR.” “CENTER,” and “SUB” Channel Volume controls similarly are pre-programmed as

punched-through.

To set a punch through, after entering the Learning Mode, and pressing the desired key to be punched-

through, simply press the device key twice of the device to punch through to. The status LED will turn

green; press the Device Selector key again to exit Learning Mode.

Example: Punch-through the from the DVD “page” to the AMP “SURR MODE” key:

• On the HTR L76, simultaneously press-and-hold “DVD” and (OPEN/CLOSE); the Learn LED

turns steady green.

•Press “SURR MODE”; the Learn LED turns amber.

•Press “AMP” twice; the Learn LED turns green.

•Press “DVD” again to exit the learning mode.

IDENTIFICATION OF CONTROLS

13

GB

COPY A COMMAND FROM ANOTHER KEY

You may copy a command from any HTR L76 key to any other. To copy a key function, after entering the

Learning Mode, and pressing the desired key to be copied to, simply press the device key from which you

wish to copy, having first pressed its Device Selector key if it resides on another “page.” The status LED

will turn green; press the Device Selector key again to exit Learning Mode.

Example: Copy the Pause command from the DVD page to the AMP key:

• On the HTR L76, simultaneously press-and-hold “AMP” and (OPEN/CLOSE); the Learn LED

turns steady green.

•Press (pause); the Learn LED turns amber.

•Press “CD”; press (pause); the Learn LED turns green.

•Press “AMP” again to exit the learning mode.

NOTE

The copy and punch-through functions are similar. However, if you copy a command and then

subsequently delete, or over-write the original (source-key) command , the copied-to key’s command

remains unchanged. If you punch-through to a command and then delete or over-write the original

key, the punched-through functions also change accordingly.

MACRO COMMANDS

A “macro” command is a series of two or more remote codes issued automatically from a single keypress.

You might use a macro to automate a simple command sequence, such as, “Turn on the DVD player and

then press ‘play.’” Or you might compose an elaborate macro to power up an entire system, select a

source, choose a SURROUND MODE, and begin playback-again, all from a single keypress. The HTR L76

can store one macro on each of its function keys (these exclude the Device Selector keys).

NOTE

Macros are independent of the currently selected device.

RECORDING MACROS

To record a macro, simultaneously press-and-hold for 3 seconds both the “MACRO” key and the HTR L76

function key to which you wish to assign the macro, until the status LED turns green. The macro button

will also light up. Press the sequence of function keys to be recorded into the macro, being sure to first

press the requisite Device Selector key for each function (you may switch devices while recording the

macro as many times as necessary), allowing you to create macro containing commands from more than

one Device Selector “page.” When you have finished entering the desired command sequence, press

“MACRO” again to store the macro; the Learn LED and “MACRO” key illumination will turn off.

NOTE

Each macro can store a maximum of 64 command steps. If you exceed this number, the macro will

be stored automatically after the 64th command is added.

Example: Record a Macro to the “0” key to Turn on the L56, Select the DVD Input, and

Commence Playback:

• On the HTR L76, simultaneously press-and-hold “MACRO” and “0” (numeric zero); the Learn LED

turns steady green.

•Press “AMP”; press “ON”; press “1” (orange “DVD”); press “DVD”; press “play” (the Learn LED

blinks as each step is added).

•Press “MACRO” again to exit the macro-record mode.

To clear a macro, perform the above steps without entering any functions.

IDENTIFICATION OF CONTROLS

14

GB

EXECUTING MACROS

To execute a macro, press and release “MACRO”; its key illumination lights for 5 seconds. While it remains

lit, press an HTR L76 key to which a macro has previously been stored. The corresponding macro will run;

as each step executes, its “parent” Device Selector’s key flashes lights briefly; when execution is finished,

the “MACRO” key illumination goes out. Pressing any other HTR L76 key while a macro is executing will

abort the macro. Remember that you must hold the HTR L76 so that its infrared emitter can activate the

target components.

NOTE

When a macro executes, a 1 second delay is automatically inserted between its commands. If you

need more than a 1 second delay between particular commands-for example, to permit a component

to power up completely-you can record “empty” steps into the macro by changing Device Selector

“pages” without entering actual command functions.

KEY-ILLUMINATION TIMEOUT

The HTR L76’s key-illumination can be set to remain lit for 0-9 seconds. The default value is 5 seconds.

To set the illumination timeout, simultaneously press-and-hold for 3 seconds both the HTR L76s “DISP”

and the “0-9” key, with the digit corresponding to the desired timeout duration; the Learn LED will flash

twice to confirm the new setting. When set to zero, the illumination will not turn on at all.

NOTE

Key illumination is the biggest drain on the HTR L76s batteries. A short key-illumination timeout will

extend battery life appreciably; turning it off altogether (set it to 0 seconds) will lengthen it still further.

FACTORY RESET

The HTR L76 can be reset to its factory state, deleting all learned commands, copied and punched-

through keys, macros, and other setup information, reverting all keys to their pre-programmed library

commands. To perform a factory reset simultaneously press-and-hold for 10 seconds the HTR L76’s “ON”

and “RTN” keys; the Learn LED will start to flash green. Release “ON” and “RTN” before the second flash

is complete; the Learn LED will turn red, indicate the remote has been reset.

NOTE

You must release “ON” and “RTN” before the second flash goes out, otherwise the unit will not reset;

should this occur, repeat the full procedure.

DELETE MODE

The HTR L76 can store learned, copied, and “default library” commands on any single key. (The default

library commands are the pre-programmed NAD codes, such as the native L76 commands on the “AMP”

“page.”) You can delete commands by layers back “down” to the default library command on any key,

removing learned commands, punched-through functions, and copied keys.

NOTE

The default library commands cannot be deleted, so you need not worry that using Delete Mode

might cause irreparable changes.

To enter Delete Mode, simultaneously press-and-hold for 3 seconds both the desired key’s Device Selector

key and the “RTN” key, until the Learn LED turns green. Press the function key whose command you wish

to delete; the Learn LED flashes; the number of times indicates which type of function has become active-

see the table below. Press the active Device Selector key again to exit Delete Mode.

NOTE

You may delete multiple function-key commands on the same Device Selector “page,” but to delete

from more than one Device Selector page you must exit Delete Mode and then re-enter it on the

required page.

Flashes Command Type

1 Default Library Command

2 Copied Library Command

3 Learned Command

IDENTIFICATION OF CONTROLS

15

GB

LOADING CODE-LIBRARIES

The HTR L76 can store a different library of default NAD codes for each of its Device Selector “pages.” If

the original default library does not control your NAD CD player, tape deck, DVD player, or other

component, follow the procedure below to change the code-library.

Begin by ensuring that the component you wish the HTR L76 to control is plugged in and powered-up

(“on,” not merely in standby). To enter the HTR L76’s Library Mode, simultaneously press-and-hold for 3

seconds both the desired Device Selector key and the “PROGRAM” key, until the Learn LED turns green.

While keeping the HTR L76 pointed toward the component, enter the first appropriate three-digit code-

library number from the table below. If the component turns off, press “ENTER” to accept that code-

library number and exit the Library Mode. If the component does not turn off, enter the next three-digit

code-library number from the table. When you enter the correct number the component will turn off;

press “ENTER” to accept that code-library number and exit the Library Mode.

NAD-brand component HTR L76 code-library numbers

CD Player (new) 200

CD Player (old) 201

DVD T562 600

DVD T550, L55 601

DVD T531, T571 602

DVD T512, T532, T572 602

SEARCH MODE

If none of the codes from the table turn off the component, and if you are quite sure you have followed

the above procedure completely and carefully, you may want to try the “search” method as follows:

Enter Library Mode by simultaneously pressing-and-holding for 3 seconds both the desired Device Selector

key and the “PROGRAM” key, until the Learn LED turns green. Now press-and-hold the HTR L76’s

or key; the remote will step through all the available codes at a rate of approximately 1 per second.

When the component turns off, immediately release the cursor key; press “ENTER” to accept that code-

library and exit the Library Mode. Try a few commands; should you prove to have stepped past the needed

code-library, re-enter the Library Mode and use the cursor key to step back to it.

NOTE

It is possible that search mode will find code-libraries that operate, at least partially, some other-brand

(non-NAD) components. You may certainly exploit such capabilities as you find them. However, since

we can only ensure the completeness or accuracy of NAD code-libraries, we cannot support the HTR

L76’s operation with other-brand components.

IDENTIFICATION OF CONTROLS

16

GB

CHECKING CODE-LIBRARY NUMBER

You can check the current code-library on any Device Selector key as follows. Enter Library Mode by

simultaneously pressing-and-holding for 3 seconds both the desired component’s Device Selector key and

the “PROGRAM” key, until the Learn LED turns green. Press the “DISP” key; the HTR L76 indicates the

current code-library by flashing its “TAPE”, “VCR”, and “MACRO” keys. For example, to indicate code-

library #501 the HTR L76 will flash “TAPE” 5 times, pause, and then flash “MACRO” once. You might

wish to make a note of your components’ code-library numbers.

SUMMARY OF HTR L76 MODES

Mode Keys To Press (for 3 seconds)

Learn/Copy/Punch Through Device Key + OPEN/CLOSE Key

Delete Mode Device Key + Return Key

Macro Record Macro Key + Function Key

Library Mode Device Key + Program Key

Back Light Timeout Display Key + Digit Key

Factory Reset (see “Factory Reset,” above)

IDENTIFICATION OF CONTROLS

17

GB

18

CONNECTING TO A TV

Installation

CONNECT THE DVD PLAYER TO YOUR TV

To S-VIDEO OUT

To SCART VIDEO

OUT (EUR VERSION)

To AUDIO OUT (L/R)/VIDEO OUT

If the TV has an S-

video input, connect

the DVD player with

the S-video cable.

AUDIO/VIDEO cable (supplied)

TV or monitor with

audio/video inputs

To audio inputs

To video input

SCART VIDEO cable (not supplied)

S-video cable (not supplied)

NOTES

• Refer to the owner’s manual of your TV as well.

• When you connect the DVD player to your TV, be sure to turn off the power and unplug both units from the wall outlet before making any

connections.

• Connect the DVD player to your TV directly. If you connect the DVD player to a VCR, the playback picture will be distorted because DVD video

discs are copy protected.

• To connect with S-video or SCART VIDEO (Component Video), you have to select TV output mode properly (Refer to “selecting TV Output” on

Page 35).

GB

19

CONNECTING TO AN AUDIO SYSTEM

Installation

NOTES

• Refer to the owner’s manual of your audio system as well.

• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before

making any connections.

• If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, move the DVD player away from the

tuner and radio.

• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise,

the speakers may be damaged by a sudden high volume sound.

• Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the speakers may be

damaged.

WARNING

Do not set the Digital Audio Output of this DVD player to “Dolby Digital” unless you are connecting the DIGITAL AUDIO jack of this DVD player

to an AV decoder that has the Dolby Digital decoding function. High volume sound may damage your hearing as well as the speakers (Refer to

“Selecting Digital Audio Output” on page 37).

YOU CAN LISTEN TO THE SOUND OF AUDIO CDS AND DVD VIDEO DISCS IN STEREO

To S-VIDEO OUT

To VIDEO OUT

If the TV has an S-video

input, connect the DVD

player with the

S-video cable.

Audio System

To audio inputs of

the amplifier

Audio Cable (Supplied)

To video input (yellow)

S-video cable (not supplied)

TV or monitor with

audio video inputs

Video cable (Supplied)

NOTES

To enjoy Dolby Digital sound from this DVD player you need the following:

• DVD recorded in Dolby Digital

• 6 channel receiver equipped with a Dolby Digital decoder or Dolby Digital processor and power receiver

• 5 speakers and 1 subwoofer

• To enjoy Dolby Digital sound, you need to select “Dolby Digital” on the SETUP menu.

GB

20

CONNECTING TO OPTIONAL AUDIO SYSTEM

Installation

ENJOYING DOLBY DIGITAL SOUND

You can enjoy the high quality dynamic sound of Dolby Digital (AC-3), Dolby Pro Logic, and 2 Channel Digital Stereo.

DOLBY DIGITAL

Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the

home. You can enjoy motion picture and live concert DVD video discs with this dynamic realistic sound by connecting the DVD player to a 6 channel

receiver equipped with a Dolby Digital (decoder or Dolby Digital processor).

L76 Rear

To S-VIDEO OUT or

VIDEO OUT

S-Video cable or Video cable

To DIGITAL OUT (COAXIAL or OPTICAL)

Receiver equipped

with a Dolby

Digital decoder

To S-video input or

Video Input

To digital audio input Connection

example

L76AV Receiver

Front

speaker

(left)

Front

speaker

(right)

Centre

speaker

Rear speaker (left

surround)

Rear speaker (right

surround)

• Refer to the owner’s manual of your audio equipment as well.

• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet before

making any connections.

• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise,

the speakers may be damaged by a sudden high volume sound.

• Turn off the receiver before you connect or disconnect the DVD player’s power cord. If you leave the receiver power on, the speakers may be

damaged.

Manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby”, and the double-D symbol are trademarks of Dolby Laboratories

Subwoofer

Page is loading ...

NAD l 56 User manual

This manual is also suitable for

NAD l 56 User manual

in other languages

Related papers

Other documents