Uniden CXA 15698 User manual

Brand: Uniden

Model: CXA 15698

Category: Telephones

Type: User manual

This manual is also suitable for

CXAI 5198

SERIES

OWNER'S

MANUAL

[1]

www.uniden.com

WELCOME/FEATURES 2

TERMINOLOGY 3

CONTROLS & FUNCTIONS 4

GETTING STARTED 6

Setting up the Phone 6

Installing the Beltclip 11

Optional Headset Installation 12

SETTING UP YOUR PHONE 13

Base Setup 13

Handset Setup 16

BASICS 19

Using Your Phone 19

Call Waiting 22

Placing a Call on Hold 22

Adjusting the Ringer, and Earpiece and

Speaker Volume 23

Muting the Ringer 24

Mute Base Microphone 25

Tone Dialing Switch-over 25

Traveling Out of Range 25

Selecting a Different Channel 26

Conferencing 26

Intercom 27

USING THE SPEED DIAL MEMORY 29

Using the Speed Dial Memory 29

CALLER ID 34

Caller ID and Caller ID on Call Waiting (CIDCW) 34

THE INTEGRATED ANSWERING DEVICE 38

The Integrated Answering Device 38

Setting Up the Answering Machine 39

Turning the Answering System On/Off 41

Setting Your Outgoing Message (Greeting) 42

Using Your Answering System 43

Remote Operation 48

ADDITIONAL INFORMATION 52

Note on Power Sources 52

General Information 54

TROUBLESHOOTING 55

Liquid Damage 57

PRECAUTIONS & WARRANTY 58

I.C. NOTICE 60

INDEX 61

REMOTE OPERATION CARD 62

Contents

WELCOME/FEATURES [2]

www.uniden.com

Welcome

Features

Congratulations on your purchase of the Uniden Cordless Telephone System! This is a

“Corded/Cordless” Telephone unit. The corded handset (on base) can make/receive

calls during power failure. You can now place a fully-featured cordless handset

anywhere in your home or office where AC power is available to connect the handset

charger.

Note: Illustrations in this manual are used for explanation purposes.

Some illustrations in this manual may differ from the actual unit.

• 5.8GHz Extended Range Technology

• Corded/Cordless Telephone System

• Make and Receive Calls During a Power Failure

• Integrated Answering Device

• Caller ID and Caller ID on Call Waiting

• 50 Caller ID feature

• Dual Keypad and LCD Screen at Base

• 10 Number Memory Dialing in the Base and Handset

• Trilingual Display Options and Voice Prompts (English, French and Spanish)

• Intercom Between Handset and Base

• Mute and Hold Features

• Do Not Disturb (DND) Feature

• Clock Display

• Base Speakerphone

WELCOME/FEATURES

[3] TERMINOLOGY

www.uniden.com

This series features AutoTalk™ and AutoStandby™. AutoTalk allows you to answer a call by just removing the

handset from the cradle so you don't have to waste time pushing buttons. AutoStandby allows you to hang

up by simply returning the handset to the cradle.

To protect you against mis-billed calls that might result from your phone being activated by other

equipment, one of more than 10,000 digital security codes is set for your phone.

Be sure to visit our web site: www.uniden.com

Uniden

is a registered trademark of Uniden America Corporation.

AutoTalk, AutoStandby and UltraClear Plus are trademarks of Uniden America.

Terminology

•Standby Mode - The handset may be sitting or off the cradle, but is NOT in use. talk/flash has not been pressed. The

corded base handset is on the base and

(speaker) on the base has not been pressed. No dial tone

is present.

•Talk Mode - The handset is off the cradle and talk/flash has been pressed, or pick up the corded base handset or

(speaker) on the base is pressed and enabling a dial tone.

Talk and Standby Times

With average use, your handset battery provides approximately 6 hours of talk time and approximately 10

days of standby time. When your handsets are not being used and are left off of their charging cradles,

the battery will gradually discharge. You can achieve optimum battery life and performance by returning

the handset to the charging cradle after each use. If the handset is left off of the charging cradle, the

actual talk time duration will be reduced respective to the amount of time the handset is off of the

charging cradle.

TERMINOLOGY

CONTROLS & FUNCTIONS [4]

www.uniden.com

Controls & Functions

1. Handset antenna

2. Beltclip hole

3. Jack for optional headset

4. Handset battery compartment

5. Handset earpiece

6. LCD display

7. call id (Caller ID)/menu (P.16, 35)

8. /vol/ (volume & scroll) (P.16, 23)

9. /vol/ (volume & scroll) (P.16, 23)

10.

/tone/ (left cursor) (P.25, 30)

11. redial/pause (P.21, 31)

12. select/int’com (P.16, 27)

13. Handset microphone and

ringer speaker

14. memory (P.29)

15. end (P.21, 24)

16. talk/flash (P.19, 22, 26)

17. #/ (right cursor) (P.30)

18. rec (record)/remote/call screen (P.47, 50)

19. delete/channel (P.26, 30, 36)

20. Handset charging contacts

Play

Skip

Answering System On

Answering System Off

Voice Prompts

Stop

Delete

Repeat

Retrieve TAD message

with Handset Remote keys

CONTROLS &

FUNCTIONS

[5] CONTROLS & FUNCTIONS

www.uniden.com

21 27

37 38 39

40 41 42

49 50

28 2930

22 23 242526

21. memo/call rec (record) (P.46, 47)

22. Message LED

23. In use LED

24. (repeat/rewind) (P.44)

25. call id (P.35)

26. (play/stop) (P.44)

27. LCD display

28. (skip/forward) (P.45)

29. mem (memory) (P.29)

30. delete (P.30, 36, 45)

31. Corded base handset

32. Base speaker

33. answer on/off/answer on/off LED

(P.41)

34. hold/hold LED (P.22)

35. mute/mute LED (P.24, 25)

36. Curl cord

37. find hs (handset)/intercom (P.27)

38. clock/menu (P.13, 39)

39.

/tone/

(left cursor) (P.25,

)

40. ///select/volume (volume,

scroll & select) (P.13, 24, 35)

41. Mic (microphone)

42. #/ (right cursor)(P.30)

43. greeting (P.42)

44. do not disturb/do not disturb LED

(P.24)

45. set (P.13, 39)

46. redial/pause (P.21, 31)

47. flash (P.22)

48. (speaker)/speaker LED

(P.20, 26)

49. DC IN 9V Jack

50. TEL LINE Jack

51. Base attenna

52. Wall mount adapter

53. Charging contacts

54. Charge LED

55. DC IN 9V Jack

CONTROLS &

FUNCTIONS

GETTING STARTED [6]

www.uniden.com

Setting up the Phone

Do the following steps:

A. Choose the best location

B. Connect the base unit

C. Install the rechargeable battery pack into the handset

D. Connect the charger

E. Mount the base unit on a wall (if desired)

A. Choose the best location

Before choosing a location for your new phone, read “Installation Considerations” on

page 59. Here are some important guidelines you should consider:

Avoid noise sources such as a window

by a street with heavy traffic

Avoid microwave ovens

Avoid excessive

moisture, extremely

low temperatures,

dust, mechanical

vibration, or shock

Avoid personal computers

Avoid other cordless telephones

Choose a central location

Avoid heat sources, such as

radiators, air ducts, and sunlight

Avoid television sets and

other electronic equipment

If your home has specially wired alarm equipment connected to phone line, be sure that installing the system does not

disable your alarm equipment.

If you have questions about what will disable alarm equipment, contact your telephone company or a qualified installer.

note

Keep the antenna free of

obstruction.

note

GETTING STARTED

[7] GETTING STARTED

www.uniden.com

B. Connect the base unit

1) Connect to the handset cord to the left side of the

phone and the corded base handset.

2) Connect AC adapter to the DC IN 9V jack and to a

standard 120V AC wall outlet.

Connect the AC adapter to a continuous power supply

(i.e., an outlet that is not controlled by a switch).

Place the base unit close to the AC outlet to avoid

long extension cords.

3) Connect the telephone line cord to the TEL LINE jack

and to a telephone outlet.

4) Set the base on a desk or tabletop. Place the corded

base handset on the base.

If your telephone outlet isn't modular, contact

your telephone company for assistance.

•Use only the supplied

[AD-830] AC adapter.

Do not use any other

AC adapter.

•Do not place the power

cord where it creates a

trip hazard or where it

could become chafed

and create a fire or

electrical hazard.

note

GETTING STARTED

GETTING STARTED [8]

www.uniden.com

C. Install the rechargeable battery pack into the handset

1) Press down on the handset battery case cover (use the finger

indention for a better grip) and slide the cover downward to

remove.

2) Plug the battery pack connector (red & black wires) into the

jack inside the battery compartment. (The connector notches

fit into the grooves of the jack only one way.) Match the wire

colors to the polarity label in the battery compartment,

connect the battery and listen for a click to insure connection.

3) Make sure you have a good connection by slightly pulling on

the battery wires. If the connection is secure, the battery jack

will remain in place.

4) Place the battery case cover back on the handset and slide it

upwards until it clicks into place.

Use only the Uniden

(BT-905) rechargeable

battery pack supplied

with your cordless

telephone.

note

GETTING STARTED

[9] GETTING STARTED

www.uniden.com

D. Connect the charger

The handset is powered by a rechargeable battery pack. The battery recharges

automatically when the handset is placed in the charger.

1) Connect the AC adapter to the DC IN 9V

jack and to a standard 120V AC wall

outlet.

2) Set the charger on a desk or tabletop, and

place the handset in the charger with the

keypad facing forward.

3) Make sure that the charge LED

illuminates.

If the LED does not illuminate, check to

see that the AC adapter is plugged in and

the handset makes good contact with the

base charging contacts.

4) Charge the handset battery pack for at least 15-20 hours before using your new cordless

handset for the first time.

To AC outlet

AC adapter

(supplied)

To DC IN 9V

Use only the supplied

AC adapter (AD-310).

Do not use any other AC

adapter.

note

GETTING STARTED

GETTING STARTED [10]

www.uniden.com

E. Mount the base unit on a wall (if desired)

Standard wall plate mounting

This phone can be mounted on any standard wall plate.

1) Remove the wall mount adapter from the

base and snap it into the notches on the

bottom of the base.

2) Plug the AC adapter to the DC IN 9V jack.

3) Wrap the AC adapter cord inside the

molded wiring channel as shown.

4) Plug the AC adapter into a standard 120V

AC wall outlet.

5) Plug the telephone line cord into the TEL

LINE jack.

6) Wrap the cord inside the molded wiring

channel as shown.

7) Plug the telephone line cord into the

telephone outlet.

8) Align the mounting slots on the base with

the mounting posts on the wall.

Then push in and down until the phone is

firmly seated.

9) On the base unit, pull the handset retainer

out of the slot. Rotate it clockwise 180 degrees.

10)Flip the retainer from front to back. Slide it back

into the slot so that the lip of the retainer is up

and the oval is down. The retainer holds the

handset in place.

GETTING STARTED

[11] GETTING STARTED

www.uniden.com

Direct wall mounting

If you don't have a standard wall plate, you can mount your phone directly to the wall.

Before doing this, consider the following:

• Avoid electrical cables, pipes, or other items behind the mounting location that could cause a

hazard when inserting screws into the wall.

• Try to mount your phone within 5 feet of a working phone jack to avoid excessive cord

lengths.

• Make sure the wall material is capable of supporting the weight of the base and handset.

• Use #10 screws (minimum length of 1-3/8 inches) with anchoring devices suitable for the wall

material where the base unit will be placed.

1) Insert two mounting screws into the wall, (with their appropriate anchoring device),

3-15/16 inches apart. Allow about 1/8 of an inch between the wall and screw heads for

mounting the phone.

2) Refer to steps 1 through 8 on page 10 to mount the telephone.

Installing the Beltclip

To attach the beltclip

Insert the beltclip into the holes on each side of the handset. Press down until it

clicks.

To remove the beltclip

Pull both sides of the beltclip to release the tabs from the holes.

GETTING STARTED

GETTING STARTED [12]

www.uniden.com

Optional Headset Installation

Your phone may be used with an optional headset. To use this

feature, insert the headset plug into the headset jack. Your

phone is ready for hands-free conversations. (Headsets may be

purchased by visiting our website at www.uniden.com or by

calling our Parts Department. See back cover page.)

GETTING STARTED

[13] SETTING UP YOUR PHONE

www.uniden.com

Base Setup

Below are some tips for using the software interface on your phone.

•Press clock/menu on the base to access the base main menu.

• Use the volume up or down key (///select/volume) to

scroll through options.

•Press

set on the base to make a selection.

• For your convenience, voice prompts will guide you through the base main menu (except LCD

contrast and Dial mode setting).

•Press clock/menu or (play/stop) on the base to return to standby mode.

• If you do not press a key within 30 seconds, the phone will time out and exit the menu mode.

When setting Day and Time, the time-out period is extended to two minutes.

Adjusting the LCD Contrast

Contrast adjusts the base LCD brightness. Choose one of the ten levels for optimum

viewing.

1) Press clock/menu on the base.

2) Press the volume down key to move the pointer to select

LCD Contrast

and then press set.

3) Press the volume up or down key to adjust the contrast of

the LCD (ten levels.)

4) Press set. You will hear a confirmation tone.

6KOG

5GEWTKV[%QFG

4KPI6KOG

.%&%QPVTCUV

.GXGN

2TGUUQTUGV

SETTING UP YOUR

PHONE

SETTING UP YOUR PHONE [14]

www.uniden.com

Setting the Dial Mode

Dial Mode sets the dial mode to tone or pulse. Most phone systems use tone dialing;

the default setting is tone dialing. Set the dialing mode to match the dialing system

used by your local phone service.

• If you are not sure of your dialing system, make a trial call. If the call connects, leave the

setting as is; otherwise set the unit to pulse dialing.

• If your phone system requires pulse dialing and you need to send DTMF tones in certain

situations during a call, you may switch over to tone dialing (refer to “Tone Dialing Switch-

over” on page 25).

1) Press clock/menu and the volume down key to move the

pointer to select

Dial Mode

, and then press set.

2) Press the volume up or down key to select

Tone

Pulse

(the initial setting is Tone).

3) Press set. You will hear a confirmation tone.

Setting Day and Time

Day & Time sets the day and time of your display.

1) Press clock/menu on the base.

2) Press set to select

Time

. The system announces “Time”,

the current time and the guidance for the setting the time.

3) Press the volume up or down key to select the day of the

week, and then press set.

4) Enter a two-digit number (01-12) to set hour, and then press set.

5) Enter a two-digit number (00-59) to set minute, and then press set.

6) Press the volume up or down key to choose

, and then press set. You hear a

confirmation tone.

&KCN/QFG

6QPG

2TGUUQTUGV

Use delete to edit

the hour and minute.

note

SETTING UP YOUR

PHONE

[15] SETTING UP YOUR PHONE

www.uniden.com

Setting the Area Code

If you enter a 3-digit area code number in the Area Code option, your local area code

does not appear in the Caller ID message. For calls received from outside your local

area code, you will see a full 10-digit number.

1) Press clock/menu and the volume down key on the base

to select

Area Code

, and then press set.

2) Press the number keypad (0-9) to enter a 3-digit area

code.

3) If you press set, the stored number will be transferred to the handset. If the transfer

is successful, you will hear a confirmation tone from the base and handset.

Otherwise,

Area Code Setting Failed!

appears on the display and an error tone

sounds. You will have to start over with the procedure you are performing.

Setting Caller ID on Call Waiting (CIDCW)

Caller ID on Call Waiting (CIDCW) displays the name and number of an incoming call

while you are on the line.

1) Press clock/menu and the volume down key on the base

to select

CIDCW

, and then press set.

2) Press the volume up or down key to select

Off

, and

then press set. You will hear a confirmation tone.

#TGC%QFG

2TGUUQTUGV

%+&%9

1P

2TGUUQTUGV

If the area code has

already been stored in

memory, the stored area

code will be displayed.

To change it, use

delete and number

keys to enter the new

area code.

note

SETTING UP YOUR PHONE [16]

www.uniden.com

Setting the Language of your Answering System and the Base Display

Language allows you to set the language of your answering system announcements to

English, French, or Spanish.

1) Press clock/menu and the volume down key on the base

to select

Language

, and then press set.

2) Press the volume up or down key to choose

English

Fran ﾕ ais

(French), or

Espa ﾃ ol

(Spanish).

3) Press set. You will hear a confirmation tone.

Handset Setup

Using the interface

Below are some tips for using the software interface on your phone.

• Press and hold call id/menu on the handset to access the

main menu.

• Use the volume up key or volume down key (//vol/) to

scroll through options.

•Press select/int’com on the handset to make a selection.

•Press end or call id/menu on the handset, or return the handset to the cradle to

return to standby.

.CPIWCIG

'PINKUJ

2TGUUQTUGV

#WVQ6CNM1HH

.CPIWCIG'PI

#TGC%QFG

SETTING UP YOUR

PHONE

[17] SETTING UP YOUR PHONE

www.uniden.com

Setting AutoTalk

AutoTalk allows you to answer the phone simply by removing the handset from the

cradle. You do not have to press any buttons to answer the call.

1) Press and hold call id/menu on the handset. Press

select/int’com to turn AutoTalk on.

2) Press end. The handset returns to standby mode.

Selecting a Language (Handset only)

You can change the language the menu display will use. Choose from English, French,

or Spanish.

1) Press and hold call id/menu on the handset.

2) Press the volume down key to move the pointer to select

Language

3) Press select/int’com to select from

Eng

(English),

(French),

Esp

(Spanish).

4) Press end. The handset returns to standby mode.

#WVQ6CNM1HH

.CPIWCIG'PI

#TGC%QFG

#WVQ6CNM1P

.CPIWCIG'PI

#TGC%QFG

SETTING UP YOUR PHONE [18]

www.uniden.com

Checking Area Code selected from the Handset

You can only check the Area Code number you have set. If you want to enter or edit the

number, refer to “Setting the Area Code” on page 15.

1) Press and hold call id/menu on the handset.

2) You can check the number entered in Area Code.

3) Press end. The handset returns to standby mode.

#WVQ6CNM1HH

.CPIWCIG'PI

#TGC%QFG

SETTING UP YOUR

PHONE

[19] BASICS

www.uniden.com

Using Your Phone

Power Failure Operation

Because the phone is a corded/cordless combination phone, it can still perform several

of its functions during a power failure. The following features will function even during

a power failure.

--Making and receiving calls with the corded base handset

--Adjusting the volume on the main base

--Call waiting/flash feature on the main base

All other features are disabled during a power failure.

Making and Receiving Calls

Making a call

From the handset

1) Remove the handset from the cradle.

2) Press talk/flash.

3) Listen for the dial tone.

4) Dial the number.

1) Remove the handset from the cradle.

2) Dial the number.

To insert a two-second pause in the dialing sequence, press redial/pause.

appears in the display.

BASICS

Page is loading ...

Uniden CXA 15698 User manual

Brand: Uniden

Model: CXA 15698

Category: Telephones

Type: User manual

This manual is also suitable for

Download PDF

report

Uniden CXA 15698 User manual

This manual is also suitable for

Uniden CXA 15698 User manual

Related papers

Other documents