Page is loading ...
Please READ this m anual carefully
before operating the unit, and keep
it for future re ference.
COLOR TV RECEIVER
OWNER'S MANUAL
The O w ner‘s M anual for the Follow M odels:
29F5D, 34F5D
* For your enjoym ent of this TV set, please read this m anual carefully and
keep it good for future reference.
CONTENTS
Before Operation
Basic Operation
Technical operation
Warning and cautions............................................................................................2
Installation..........................................................................................................3
Antenna connection...........................................................................................3
Preparation for the re m o te contro l........................................................................3
Position of Button and Plug-ins................................................................................4
Front and side panel ..........................................................................................4
B ack panel.......................................................................................................4
Function button of the re m o te contro l........................................................................5
The screen display m enu........................................................................................6
Switch on/off the TV set..........................................................................................7
Watching TV program s...........................................................................................8
Watching TV program .........................................................................................8
Program sw ap and auto scan functions..................................................................9
Tune.................................................................................................................10
Auto search....................................................................................................10
Search...........................................................................................................11
Fine tune and P rogram lock functions..................................................................12
Skip unnecessary channel.................................................................................13
Exchange program s.........................................................................................14
Picture adjusting...
............................................................................................15
Select
the picture m odes and set the picture quality...........................................15
Color Te m p function...........................
.............................................................16
3A Optimize and 3DNR functions.......................
..............................................17
Com b filter and LayerE n./ Color En. Functions................................
..................18
S ound adjusting............................................................................
....................19
Select the sound m odes and set the sound quality.............................................19
Equalizer and mute
functions..........................................................................20
Time set up function.............
..............................................................................21
Set current time and on/off time f
unctions.........................................................21
Rem ind P rogram Function..............................
................................................22
Set up function............................................
......................................................23
Select the m enu Language and S creen saver functions...........................
..........23
Select Switch on m ode and HDM scan function.................................................24
Tilt function and setting Transparency
m enu.....................................................25
Setting the Lock........................................
.........................................................26
C hange your passw ord...................................
................................................26
Setting the Lock........................................
.....................................................27
Others functions..................................................................................................28
Calendar,picture still and zoom functions.........................................................28
Setting and Using Favorite program s, Setting Sleep Timer ................................29
VGA input adjustm ent.......................................................................................30
Multi-M edia Player system .................................................................................31
Multi-M edi
a Player P reparation........................................................................31
To operate the m enu.............
...........................................................................33
Multi-M edia player..............
............................................................................34
C opy file function...........
.................................................................................38
Set up functions........
......................................................................................39
External connections...........................................................................................40
Video/A udio output connection,VG A input............................................................40
Video/A udio input connection.............................................................................41
Others
Trouble shooting.................................................................................................42
Specifications.....................................................................................................43
Warning and Cautions
1. W hen you clean the TV set, please
pull out the pow er plug from AC outlet.
D on’t clean the cabinet and the
screen with benzene, petrol and other
chem icals.
4. Do not place the TV set near rain or
moisture as it m ay cause an electric
shock, or the TV set to catch fire. The
TV set must only
be used in dry in
door locations.
2. In order to prolong the using life of
the TV set, please place it in a w ell
ventilated location.
5. T he back cover must only be
rem oved by a registered electrical
service person. Rem oving the back
cover may result in electric
shock, fire
or dam age to
the TV set.
3. D on’t place the
TV set in direct
sunlight or near a
heat source.
6. If the TV set is not going to be used
for a long time, or there is a severe
thunder & Lighting storm , it is
recom m ended that the TV set be
disconnected from the AC pow er outlet
and the aerial plug rem oved.
Explanation on the display tube
Should the picture tube require cleaning, disconnect the pow er and use a dry
soft cotton cloth. Do not use any cleanser or abrasive cloths.
Installation
Antenna connection
G eneral speaking, to enjoy a clearer picture, we recom m end that you use a CATV
system or an outdoor antenna .In different places, the suitable antenna type and position
are different.
300 twin-lead cable
Antenna adapter
(additional purchase)
75 coaxial cable
Plug
(additional purchase)
Mixer
additional
purchase
Antenna input
75 standard
coaxial type
AC pow er socket
Note
It is recom m ended that you’d better use 75
D on’t bind antenna cable and electric wire together.
coaxial cable to rem ove the
disturbance caused by airwave.
Preparation for the rem ote control
* the plug type may vary
depending on the m odel.
Battery installation
Take off the battery com partm ent cover. Place two AA batteries, make sure that battery
polarity matches with the +/- mark inside the battery com partm ent.
O peration notes for the rem ote control unit
U nder normal conditions, the life time of batteries is one year.
If you don’t intend to use the unit for a long period or the electricity of the batteries is
used up, rem ove the batteries to prevent batteri
es acid from leaking into the battery
com partm ent.
Avoid dropping the rem ote control and/or getting it wet.
Never place batteries in a fire.
S-video input terminal: S pecial video S-VIDEO AUDIO: L/MONO Track L/MONO ,R Track R
AV output terminals: VIDEO AUDIO L/MONO Track L/MONO ,R Track R
AV2 input terminals MONITO R : VIDEO AUDIO :L/MONO Track L/MONO ,R Track R
AV1 input terminals MONITO R :VIDEO AUDIO :L/MONO Track L/MONO ,R Track R
DVD com ponent terminals:
Interleaved signal Y C
b C r AUDIO L/MONO Track L/MONO ,R Track R
Progressive signal YPb Pr AUDIO L/MONO Track L/MONO ,R Track R
HDTV input terminals: YPb Pr terminal AUDIO L/MONO Track L/MONO ,R Track R
Position of Buttons and Plug-ins
Front and Side panel
B ack panel
+CH -+ VOL -
TV/AV M ENU
VIDEO
AUDIO
R
L
USB
Side AV terminal
Power sw itch
USB Terminal
Cards Jack
Infrared receiver
C hannel position up/dow n
Volum e up/ dow n
TV/Video (input selector
MENU
Power indicator
Note:
The cabinet and buttons of TV is
only for reference.
AV output terminals
Antenna input
VGA input terminal
AV2 input terminals
AV1 input terminals
YUV input terminals
S-video input terminal
YUV
VIDEO
AUDIO
VGA IN
P
r(cr)
Pb(cb)
AVO UT
L
R
AV
2IN AV1IN
L
R
L
R
L
R
1.W hen the AV 2 terminal, the side AV terminal can not be
connected at the sam e time
USB terminal or
.
2.W hen the side AV is connected, please select the AV 2 terminal.
Mute button
I/II select button
Picture still button
Screen call/help button
HDM m enu call button
Program scan button
Direct
Digital
Program sw ap button
Picture m ode selection button
Sound m ode selection button
Program
M enu call/select
button
Select m enu, call and exi
Picture m enu call/gam e direction select
Sound m enu call/gam e direction select
Favorite program button
(No available)
Function m enu call
QSET button(No available)
Zoom select button
Time skip button
Time m enu call button
Calendar /Exit button
Hotel lock button
Digital album N o available
To eliminate the sound of the program s
DC standby and pow er button
TV and AV exchange button
A changeover betw een TV and other
input signals like AV
select button
Select a TV channel di
rectly
selection button
C hangeover from one digital, two
digital and three digital
Volum e adjustm ent button
adjustm ent button
(No available)
ZOOM
CAL./EXIT
MUTE
TV/AV
POW ER
HDM
SCAN
C A LL/HELP
P.STD
S.STD
CH+
CH-
VOL- VOL+
MENU
PICTURE
FUNCTION
QSET
SHUTTLE
FAVO RITE
SOUND
STILL
SW AP
T.SKIP
TIME
H.LO C K
D.ALBUM
Function Buttons of the Remote Control
Function buttons of the re m o te contro l
MENU
Lock Set
The Screen Display Menu
For your convenience of operation, here lists the screen display m enus of this m odel
as your re ference.
Note:
W hen the TV set is pow ered on, there might be different fro m w hat have been
illustra ted above. Please do som e adjustm ent as follow s to m eet your needs.
1. P ress the M ENU button, and then press CH+/- buttons to select the m enu
in the
main m enu: PICTURE, SOUND, TUNE ,SETUP and TIMER. Off course, you may
select these m enus dire c tly by pressing the PICTURE, SOUND, TIME and FUNCTION
buttons on the re m o te contro l.
2. If it is not in sub-m enu, press the VO L-/+ buttons to enter the sub-m enu.
3. Then press the CH+/- to select the desired item , press the VO L-/+buttons to adjust
the num erical value. After that, press the MENU button to re turn the main m enu.
4. If you w ant exit the m enu, press the M ENU button repetitiously.
Picture m enu
Sound m enu
Tune m enu Setup m enu
Timer m enu
H.lock m enu
Picture M ode Standard
50
30
Brightness
C ontrast
Color
Hue
Sharpness
Advance
50
50
0
Color Tem p. Cool
Picture
Sound
Tune
Setup
Timer
Sound M ode
3D Mono Off
Off
Trubass Off
Off
0
Standard
SRS Dialog
W oofer
Balance
Equalizer
Exchange
Program edit
Search
Auto Search
Quick Search
Current Time
Off Time
On Time
O n program
Remind time
Remind program
Sleep Time
122 7
-- --
-- --
1 0
-- --
---
O ff
C hange P assw ord
New PW D ----
C onfirm PW D ----
C onfirm
Lock Off
C hannel Lock
Off
MENU
MENU
MENU
Picture
Sound
Tune
Setup
Timer
Picture
Sound
Tune
Setup
Timer
Language E nglish
Screen Saver On
Curtain
Color S ys. P A L50
HDM scan 100H z
Transparency On
Tilt
0
MENU
Picture
Sound
Tune
Setup
Timer
Picture
Sound
Tune
Setup
Timer
POW ER
Switch on/ off the TV set
In the follow ing, the methods of using pow er sw itch and rem ote control to sw itch on/off
pow er supply for the TV set will be explained.
Switch on/ off the TV set
Switch on/ off the TV set
1.C onnect the pow er supply wire. Then press the pow er
sw itch button, the pow er indicator will light, in several
seconds the picture will display on the screen.
2. If the TV is in the state of standby, press the PO W ER
button or
the CH+/- buttons on the rem ote control.
Note:
1. Press the CH+/- buttons which is on the TV set to get
out of the standby state w hen the rem ote control is not
in use.
2. P ress the PO W ER button on the re m o te contro l
t
o the standby m ode.
3. P ress the pow er button on the TV set to
com pletely pow er off the TV.
4. To eliminate the m agnetization com pletely, the
TV set degausses autom atically. There is the
sound of PENG, it is natural.
Autom atic stand by function
If no signal has been received, and after five
minutes, it will stand by autom atically.
CH+
CH-
VOL- VOL+
MENU
Watching TV Programs
Watching TV program s
CH+
CH-
VOL- VOL+
MENU
CH+
CH-
VOL- VOL+
MENU
How to select the TV program
Select the desired program
1. Use the dire c t num ber selection button
2. Use the CH+/- buttons
Press the CH+ button to select the channel of the larger num ber.
Press the CH- button to select the channel of the sm aller num ber.
Press the button from 0-9
to select a one-figure channel.
If you w ant to select a double figures channel, press the
figure-selection button and change it into two-figure m ode, then
press the num ber of the channel.
If you w ant to select a three fi
gures channel, press the figure-selection
button and change it into three-figure m ode, then press the num ber
of the channel.
Select the desired sound
Press the VO L+/- buttons to adjust the volum e to your need.
If the colour or sound of a certain channel is
abnorm al
If the TV set you bought is
abnorm al in colour or sound in a
certain channel, it might be
because the colour or sound
system has been set im properly.
You may follow the instru c tion
below to adjust it. P ress the
MENU button, then press CH+/-
buttons to select
function m enu,
and you can see the form . Then
press VO L+ button to enter sub-
m enu.
If the colour of the picture is abnorm al
Press the CH+/- buttons to move the indicator to "Color S ys.", and
press the VO L+/- buttons to select the proper color.
Refer the above steps to enter the
Program edit m enu. Press the CH+/-
buttons to move the indicator to
"
Sound S ys.", and press the VOL+/-
buttons to select the proper sound.
If the sound is abnorm al
Program NO. 2
Skip Off
Lock Off
Sound Sys. BG
Fine tune <144.20MHz>
Program edit
Language E nglish
Screen Saver On
Curtain
Color sys. P A L50
HDM scan 60H z
Transparency On
Tilt
0
MENU
Picture
Sound
Tune
Setup
Timer
CH+
CH-
VO L- VO L+
MENU
SW AP
SCAN
Watching TV Programs (continued)
Sw ap function enables quick sw ap to the last watched program .
Program sw ap and auto scan functions
Program sw ap
1.
Suppose the channel num ber
you used just now is 8 and the
channel num ber you are using
is 18 (as show n in the figure).
2. If you w ant to return to the
last watched program channel
8, you can simply press the
SW AP button.
3. If you w ant to return to
channel 18, press the button
again. Through this function,
you can easily change
betw een the channel you are
using and the channel you
used last time.
Auto program scan
1. Press the SCAN button to
scan through all the memorized
TV channels.
2.W hen it is the program that
you desired, and press the
MENU button to confirm.
CH+
CH-
VOL- VOL+
MENU
VHF-L 188.16 MHz CH NO:4
Auto Search
Tune
The TV set has three methods to set the channels, which are Auto search, S earch and Fine tune.
In this section, how to use the rem ote control to set the channel is explained. You can also use the buttons
on the TV set to set channel.
Auto search
1. Press the MENU button to display
the m enu, then press CH+/-buttons
to select TUNE m enu, press VOL+
button to enter.
2. Press the CH+/- buttons to move
the indicator to " Auto S earch ".
3. Press the VOL+ button, and
"
Auto S earch" m ode will work.
The TV set will search autom atically
all available program s, after search
is finished, all available program s
will be stored in turn.
If you w ant to stop the search,
just press the M ENU button.
The order of the autom atic search is due to the frequency of
the program , generally speaking, it is used only the firs t time
you search the program , and after the order of the program
has been m ade, you don’t have
to use this function,
otherw ise the order of the program will be mixed.
Auto search
After searching (C ontinued)
Press the CH+/- buttons to check channels.
If the colour or sound is abnormal in a certain channel, it may be
because that the colour or sound system has not been set
properly, then, you may adjust it to proper system (Refer to
page 8).
Exchange
Program edit
Search
Auto Search
Quick S earch
MENU
Picture
Sound
Tune
Setup
Timer
Exchange
Program edit
Search
Auto Search
Quick S earch
MENU
Picture
Sound
Tune
Setup
Timer
CH+
CH-
VOL- VOL+
MENU
C A LL/HELP
Tune (Continued)
Search
Search
1. Press the CH+/- buttons or Direct
select button to select the desired
channel num ber.
2. Press the MENU button to display
the m enu, then press CH+/-buttons
to select TUNE m enu, press VO L+
button to enter.
. Press the CH+/- buttons to
move the indicator to "S earch",
and then press the VOL+ button
to enter the SEARCH m enu.
4. Press the VOL+ or VO L- buttons,
the TV set will begin to search up or
dow n, w hen the TV set has searched
a program , the TV set
will stop
searching. If the program is not the
one you need, you can press the
button again, let the TV set continue
to search until it has searched the TV
signal you need.
Note:
U sually, five seconds after the channel has been changed, the channel
num ber will disappear autom atically. If you w ant to know which channel
you are watching, just press the C ALL/HELP button once.
Exchange
Program edit
Search
Auto Search
Quick Search
MENU
Picture
Sound
Tune
Setup
Timer
VHF-L 188.16 MHz CH NO:4
Search
CH+
CH-
VOL- VOL+
MENU
CH+
CH-
VOL- VOL+
MENU
CH+
CH-
VOL- VOL+
MENU
Fine Tune
Program Lock buttons
Tune (Continued)
Fine Tune and Program Lock functions
If the picture and/or sound are poor, try using the FINE
TUNE feature. Do not use this feature unless reception
is poor.
1. Press the CH+/- buttons or Direct
select button to select the desired
channel num ber. ( For exam ple, the
channel 1.)
2. Press the MENU button to display
the m enu, then press CH+/-buttons
to select TUNE m enu, press VOL+
but
ton to enter.
3. Press the CH+/- buttons to
move the indicator to " Program
edit ", then press the VOL+ button
to sub-m enu.
4. Press the CH+/- buttons to
move the indicator to " Fine Tune ".
5. Press the VOL+ button to enter
the Fine Tune M enu, and then
until it has searched the
TV signal you need.
the
VOL- button to search dow nw ards
or the VOL+ button to search
upw ards
If the program Lock and the program Lock of the Lock
Set are ON, the screen is black and LOCK will shown.
The program is locked.
1.Repeat the steps 1-4 of Fine
Tune to select the Lock item.
. Press the VOL+ button to turn
the Lock function to "O n ".
. Press the H.Lock button to turn
the Program Lock function to "O n "
(Refer to page 27),then the screen
is black. After setting the Program Lock to On, the Lock of the
Program Edit m enu will fail.
Exchange
Program edit
Search
Auto Search
Quick Search
MENU
Picture
Sound
Tune
Setup
Timer
Program NO. 2
Skip Off
Lock Off
Sound Sys. BG
Fine tune <144.20MHz>
Program edit
Program NO. 2
Skip Off
Lock Off
Sound Sys. BG
Fine tune <144.20MHz>
Program edit
CH+
CH-
VO L- VO L+
MENU
CH+
CH-
VOL- VOL+
MENU
2. Press the MENU button to display
the m enu, then press CH+/-buttons
to select TUNE m enu, press VOL+
button to enter.
3. Press the CH+/- buttons to
move the indicator to " Program
edit ", then press the VOL+ button
to sub-m enu.
1. Press the CH+/- buttons or Direct
select button to select the desired
channel num ber. ( For exam ple, the
channel 1.)
4. Press the CH+/- buttons to
move the indicator to " Skip ".
1. Use the C hannel Selection buttons to select the num ber of the
channel to be recovered.
2. R epeat those steps just now .
3. Press the VO L+/- buttons to turn the SKIP function O FF.
Tune (Continued)
Skip unnecessary channel
Skip unnecessary channel
The Program skip feature enables you to skip/hide program s
that you do not wish to be displayed w hen using the CH+/-
buttons. These channels will still be displayed by dire c tly
using the channel num ber buttons on the re m o te contro l.
. Press the VOL-/+ buttons to
turn the Skip function to "O N ".
. Press the MENU button to exit
the m enu display.
If you w ant to recover the skipped channel
Exchange
Program edit
Search
Auto Search
Quick Search
MENU
Picture
Sound
Tune
Setup
Timer
Program NO. 2
Skip Off
Lock Off
Sound Sys. BG
Fine tune <144.20MHz>
Program edit
CH+
CH-
VOL- VOL+
MENU
CH+
CH-
VOL- VOL+
MENU
Current Program 3
Exchange Program 9
Exchange
Exchange
Tune (Continued)
Exchange Programs
Exchange Programs
This feature enables TV programmes that may be on a wrong program
number to be moved to another number.
This feature is very useful when Automatic Search Tuning has been used
because programmes are stored in the order they are found, which is usually
not the desired order.
When organising, it is best to start from the lowest programme number first.
1. Press the MENU button to display
the m enu, then press CH+/-buttons
to select TUNE m enu, press VOL+
button to enter.
2. Press the CH+/- buttons to
move the indicator to " E xchange ".
3. Press the VO L+ button to
sub-m enu.
4. Press the VOL-/+ buttons to set
the Current Program to 3.
. Press the CH+/- buttons to move the indicator to " E xchange
Program ", then press the VOL-/+ buttons to set the E xchange
Program to 9.
. Press the CH+/- buttons to move the indicator to " E xchange ",
press the VOL+ button to confirm.
Exchange
Program edit
Search
Auto Search
Quick Search
MENU
Picture
Sound
Tune
Setup
Timer
CH+
CH-
VOL- VOL+
MENU
P.STD
PICTURE
Picture Adjusting
Select the picture m odes and set the picture quality
How to select the picture m odes
Y ou can quickly select the desired picture m ode from four
preset m odes and one custom ized m ode.
Standard
Soft
User
Listen
Rich
MODE
PICTURE QUALITY
M edium color and brightness
Low color and brightness
Set by yourself
No pictures)
Bright color
(
Press the P.STD button to select the desired picture quality.
Set the picture quality
W hen the Picture M ode is User m ode, you can set the picture
quality
1. Press the PICTURE button, the
Picture m enu will appear on the
screen.
. Press the CH+/- buttons to
move the indicator to the desired
option (For exam ple, C ontrast), then
press VO L-/+ buttons to set the
desired quality. Press the PICTURE
button to exit the Picture m enu.
Brightness
C ontrast
Color
S harpness
Press VO L- button
Option
Press VO L+ button
Dark
W eak
Light
Soft
Bright
Strong
Thick
S harp
Tip: HUE option is available only in N color system .
MENU
Picture Mode Standard
50
30
Brightness
Contrast
Color
Hue
Sharpness
Advance
50
50
0
Color Tem p. Cool
Picture
Sound
Tune
Setup
Timer
CH+
CH-
VOL- VOL+
MENU
Color Temp Function
Color Temp Function
PICTURE
Picture Adjusting (Continued)
1. Press the PICTURE button, the
Picture m enu will appear on the
screen.
. Press the CH+/- buttons to move
the indicator to "C o lor Tem p.".
MENU
Picture M ode Standard
50
30
Brightness
Contrast
Color
Hue
Sharpness
Advance
50
50
0
Color Tem p. C ool
Picture
Sound
Tune
Setup
Timer
. Press the VOL-/+ buttons to
select "C ool", "W a rm" or "S tandard".
CH+
CH-
VOL- VOL+
MENU
CH+
CH-
VOL- VOL+
MENU
PICTURE
PICTURE
Picture Adjusting (Continued)
3A Optimize On
Com b filter Off
3DNR Off
Layer en. Off
Color en. Off
3A Optimize and 3DNR Functions
3A Optimize Function
1. Press the PICTURE button, the
Picture m enu will appear on the
screen.
. Press the CH+/- buttons to move
the indicator to "Advance", then
press the VO L+ button to sub-
m enu.
. Press the CH+/- buttons to move
the indicator to "3 A Optimize".
. Press the VOL-/+ buttons to
select "O n ", "O ff" or "W indow ".
3DNR Function
1. Press the PICTURE button, the
Picture m enu will appear on the
screen.
. Press the CH+/- buttons to move
the indicator to "Advance", then
press the VO L+ button to sub-
m enu.
. Press the CH+/- buttons to move
the indicator to "3DNR".
. Press the VOL-/+ buttons to
select the desired item .
MENU
Picture
Sound
Tune
Setup
Timer
3A Optimize On
Com b filter Off
3DNR Off
Layer en. Off
Color en. Off
MENU
Picture
Sound
Tune
Setup
Timer
MENU
Picture M ode Standard
50
30
Brightness
Contrast
Color
Hue
Sharpness
Advance
50
50
0
Color Tem p. C ool
Picture
Sound
Tune
Setup
Timer
MENU
Picture M ode Standard
50
30
Brightness
Contrast
Color
Hue
Sharpness
Advance
50
50
0
Color Tem p. C ool
Picture
Sound
Tune
Setup
Timer
CH+
CH-
VOL- VOL+
MENU
CH+
CH-
VOL- VOL+
MENU
PICTURE
PICTURE
Picture Adjusting (Continued)
Comb filter and Layer En./Color En. Functions
Comb filter Function
Layer En./Color En. Functions
1. Press the PICTURE button, the
Picture m enu will appear on the
screen.
. Press the CH+/- buttons to move
the indicator to "Advance", then
press the VO L+ button to sub-
m enu.
. Press the CH+/- buttons to move
the indicator to "C om b filter".
. Press the VOL+/- buttons to select
"O n " or "O ff".
1. Press the PICTURE button, the
Picture m enu will appear on the
screen.
. Press the CH+/- buttons to move
the indicator to "Layer en." Or
"C o lor en.".
. Press the CH+/- buttons to move
the indicator to "Advance", then
press the VO L+ button to sub-
m enu.
. Press the VOL+/- buttons to select
"O n " or "O ff".
3A Optimize On
Com b filter Off
3DNR Off
Layer en. Off
Color en. Off
MENU
Picture
Sound
Tune
Setup
Timer
3A Optimize On
Com b filter Off
3DNR Off
Layer en. Off
Color en. Off
MENU
Picture
Sound
Tune
Setup
Timer
MENU
Picture Mode Standard
50
30
Brightness
Contrast
Color
Hue
Sharpness
Advance
50
50
0
Color Tem p. Cool
Picture
Sound
Tune
Setup
Timer
MENU
Picture Mode Standard
50
30
Brightness
Contrast
Color
Hue
Sharpness
Advance
50
50
0
Color Tem p. Cool
Picture
Sound
Tune
Setup
Timer
CH+
CH-
VOL- VOL+
MENU
Adjusting the Balance item
3D M ono
3D dynam ic surround
Setting "O n "
SRS Dialog
Trubass
W oofer
Enhance bass
Standard
News
User
Music
Standard
Speech
You can set it by yourself
Musical
Sound M ode
S.STD
SOUND
Sound Adjusting
Select the sound m odes and set the sound quality
How to select the sound m odes
Y ou can quickly select the desired sound m ode from three
preset m odes and one custom ized m ode.
Press the S.STD button to select the desired picture quality.
Four kinds of sound m odes can be selected in turn.
Sound q u a lity
Set the sound quality
W hen the Personal m ode is selected, you can
custom ize the
sound quality.
1. Press the SOUND button, the
Sound m enu will appear on the
screen.
. Press the CH+/- buttons to move
the indicator to the desired option,
then press VO L-/+ buttons to set the
desired quality. Press the SOUND
button to exit the S ound m enu.
Option
Press VOL- button P ress VO L+ button
BALANCE
R track dow n
L track dow n
Adjusting the S pecial item s
Option
SRS Dialog
Enhance w oofer
Sound M ode
3D M ono Off
Off
Trubass Off
Off
0
Standard
SRS Dialog
W oofer
Balance
Equalizer
MENU
Picture
Sound
Tune
Setup
Timer
/