Thermador HMCN36FS User manual

Brand: Thermador

Model: HMCN36FS

Category: Cooker hoods

Type: User manual

This manual is also suitable for

HMCN42FS

Thermador HMCN36FS is a high-quality ventilation hood designed for indoor use. It can be used in exhaust air mode to remove smoke, odors, and moisture from the kitchen. The hood is made of durable materials and features a sleek design that will complement any kitchen décor. It is easy to install and use, and it comes with a variety of features that make it a great choice for any home cook.

Some of the key features of the Thermador HMCN36FS ventilation hood include:

36-inch width to accommodate most cooktops
4-speed fan to adjust the airflow to your needs
LED lighting to illuminate the cooktop

Some of the key features of the Thermador HMCN36FS ventilation hood include:

36-inch width to accommodate most cooktops
4-speed fan to adjust the airflow to your needs
LED lighting to illuminate the cooktop

DOWNDRAFT

USE AND CARE

MANUAL

MODELS: CVS2

MODELS: UCV2

DOWNDRAFT

USE AND CARE MANUAL

MODEL: HMCN 36 FS / 42 FS

VENTILATION

INSTALLATION MANUAL

Page is loading ...

 WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE

FOLLOWING:

A. Installation work and electrical wiring

must be done by qualiﬁed person(s) in

accordance with all applicable codes

and standards, including ﬁre-related

construction.

B. Sufficient air is needed for proper

combustion and exhausting of gases

through the ﬂue (chimney) of fuel

burning equipment to prevent back-

drafting. Follow the heating equip-

ment manufacturer’s guideline and

safety standards such as those

published by the National Fired

Protection Association (NFPA), and

the American Society for Heating,

Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local

code authorities.

C. When cutting or drilling into wall or

ceiling, do not damage electrical

wiring and other hidden utilities.

D. Ducted fans must always be vented

to the outdoors.

E. Always unplug or disconnect the

appliance from the power supply

before servicing.

F. This unit is designed for indoor use

only. Use this unit only in the manner

intended by the manufacturer.

 WARNING

For general ventilating use only. Do not

use to exhaust hazardous or explosive

materials and vapors.

To reduce risk of ﬁre and to properly

exhaust air, be sure to duct air outside.

Do not vent exhaust air into spaces

within walls, ceilings, attics, crawl spaces

or garages.

TO REDUCE THE RISK OF FIRE, USE

ONLY METAL DUCT WORK.

To reduce the risk of ﬁre or electric

shock, do not use the fan with any solid-

state speed control device.

This appliance has been found to be in

compliance with UL 507 Standard for

Electric Fans and CAN/CSA-22.2 No.

113 Canadian Standard for Fans and

Ventilators. It is the responsibility of the

owner and the installer to determine if

additional requirements or standard

apply in speciﬁc installation.

 SAFETY INSTRUCTIONS

Read All Instructions Before Using the Appliance.

READ AND SAVE THESE INSTRUCTIONS

Parts Needed

❑ Tape Measure

❑ Phillips Head Screwdriver

❑ Duct Tape

❑ Ductwork (conﬁguration varies

depending on location; see ”Prior to

installation”).

❑ Additional Sheetmetal screws

(as necessary for ductwork installation)

Parts Supplied

❑ Appliance assembly (1)

❑ Sheetmetal Screws (6)

❑ Wood Screws (4)

❑ Counter Sink Screws (2)

❑ Hardware for brackets on vent (2)

❑ Plugs UX6 (6)

Fig. 1

GAS

ELECTRIC

IMPORTANT INFORMATION

Old appliances are not worthless rubbish.

Valuable raw materials can be reclaimed by

recycling old appliances. Before disposing

of your old appliance, render it unusable.

You received your new appliance in a

protective shipping carton. All packaging

materials are environmentally friendly and

recyclable. Please contribute to a better

environment by disposing of packaging

materials in an environmentally-friendly

manner.

The hood can only be used in exhaust air

mode.

Always mount the hood over the center of

the cooking surface.

 Minimum distance between electric

cooktop and bottom edge of hood: 30”,

Fig. 1.

 The hood must not be installed over a

wood or coal burning stove – a potential ﬁre

hazard (e.g. ﬂying sparks) – unless the stove

features a closed, non-removable cover

and all national regulations are observed.

The smaller the gap between the hood and

cooktops, the greater the likelihood that

droplets will form on the underside of the

hood.

Additional information

concerning gas cookers:

When installing gas cooktops, comply with

the relevant national statutory regulations.

Always comply with the currently valid

regulations and installation instructions

supplied by the gas appliance

manufacturer.

 Only one side of the hood may be

installed next to a high-sided unit or high

wall. Gap at least 2”.

 Minimum distance on gas cooktops

between the upper edge of the grate and

lower edge of the hood: 30”, Fig. 1.

The exhaust air is discharged upwards

through a duct or directly through the

outside wall into the open.

Exhaust air should neither be directed

into a smoke or exhaust ﬂue that is currently

used for other purposes, nor into a duct

that is used for ventilating rooms in which

stoves or ﬁreplaces are also located.

Exhaust air may be discharged in

accordance with official and statutory

regulations only (e.g. national building

regulations).

Local authority regulations must be

observed when discharging air into smoke

or exhaust ﬂues that are not otherwise in

use.

When the hood is operated in

exhaust-air mode simultaneously with a

different burner which also makes use of

the same chimney (such as gas, oil or

coal-ﬁred heaters, continuous-ﬂow heaters,

hot-water boilers) care must be taken to

ensure that there is an adequate supply

of fresh air which will be needed by the

burner for combustion.

Safe operation is possible provided that the

underpressure in the room where the burner

is installed does not exceed 4 Pa (0.04

mbar).

This can be achieved if combustion air can

ﬂow through non-lockable openings, e.g. in

doors, windows and via the air-intake/

exhaust-air wall box.

If the air intake is inadequate, there is a

risk of poisoning from combustion gases

which are drawn back into the room.

 WARNING – Avoid risk of poisoning – If

the air intake to the room is inadequate,

there is a risk of poisoning from combustion

gases which can be drawn back into the

room.

Note: When assessing the overall

requirement, the combined ventilation

system for the entire household must be

taken into consideration. This rule does not

apply to the use of cooking appliances,

such as hobs and ovens.

If the exhaust air is going to be

discharged into the open, a telescopic

wall box should be ﬁtted into the

outside wall.

PRIOR TO INSTALLATION

Step 1: EXHAUST-AIR MODE

For optimum hood efficiency:

❑ Short, smooth duct pipe.

❑

As few bends in the ducting as possible.

❑

Diameter of ducting to be as large as

possible and no tight bends in ducting.

If long, rough exhaust-air ducting,

many ducting bends or smaller pipe

diameters are used, the air extraction

rate will no longer be at an optimum

level and there will be an increase in

noise.

IMPORTANT: The manufacturer of the

hood accepts no liability for

complaints which can be attributed to

the design and layout of the duct-

work.

❑

Round pipes:

We recommend

Internal diameter: 8”.

❑

Flat ducts must have an internal cross-

section that equates to that of round

pipes.

There should be no sharp bends.

l 8” approx. 50.3 inches

❑

If pipes have different diameters:

Insert sealing strip.

❑

For exhaust-air mode, ensure that

there is an adequate supply of fresh air.

CONNECTING A l 8” EXHAUST-AIR

DUCT:

❑ Mount the duct directly onto the air out-

let on the hood.

Step 2: PREPARING THE WALL

❑ The wall must be ﬂat and perpendicular.

❑

Ensure that the wall is capable of

providing a ﬁrm hold for mounting

screws and plugs.

Weight in kg: 23.0

PRIOR TO INSTALLATION

Step 3: ELECTRICAL CONNECTION

 WARNING: THIS APPLIANCE MUST

BE GROUNDED

The hood should only be connected to a

grounded socket that has been installed

according to relevant regulations.

If possible, site the earthed socket directly

behind the chimney paneling.

❑ The grounded socket should be

connected via its own circuit.

❑ If the grounded socket is no longer

accessible following installation of the

hood, ensure that there is a permanently

installed disconnector.

Step 4: INSTALL ELECTRICAL

SERVICE

Check your local building codes for proper

method of installation. In the U.S., if there

are no applicable local codes, this unit

should be installed in accordance with the

National Electric Code ANSI/NFPA No. 70,

Current Issue. (In Canada, installation must

be in accordance with the CAN 1- B149.1

and .2 - Installation Codes for Gas Burning

Appliances and/ or local codes).

The appliance must be grounded. In the

event of an electrical short circuit, grounding

reduces the risk of electric shock by

providing an escape wire for the electric

current. This appliance is equipped with a

cord having a grounding wire with a

grounding plug. The plug must be plugged

into an outlet that is properly installed and

grounded.

 WARNING – Improper grounding can

result in a risk of electric shock.

Consult a qualiﬁed electrician if the

grounding instructions are not completely

understood, or if doubt exists as to whether

the appliance is properly grounded.

Do not use an extension cord. If the power

supply cord is too short, have a qualiﬁed

electrician install an outlet near the

appliance.

If it is necessary to wire the hood directly

into the mains:

 WARNING – Avoid risk of electrical

shock – If the connecting cable for this

appliance is damaged, the cable must be

replaced by the manufacturer or his

customer service or a similarly qualiﬁed

person in order to prevent serious injury to

the user.

ELECTRICAL DATA:

Are to be found on the name plate inside

the appliance after removal of the ﬁlter

frame.

WARNING – Avoid risk of electrical

shock – Before undertaking any repairs,

always disconnect the hood from the

electricity supply.

Length of the connecting cable: 51

”.

This hood corresponds to EC regulations

concerning RF interference suppression.

PRIOR TO INSTALLATION

Page is loading ...

Step 5: INSTALLATION

This hood is intended to be mounted onto

the kitchen wall.

1. Remove the grease ﬁlter (refer to Opera-

ting Instructions).

2. Draw a line on the wall from the ceiling to

the lower edge of the hood at the center

of the location where the hood is going

to be mounted.

3. Use the template to mark the points on

the wall where the screws will be moun-

ted. In order to make it easier to hook

the hood onto the screws, draw the out-

line of the area where the hood will be

attached.

 CAUTION – Ensure that the minimum

distance between the cooktop and the

hood is maintained – 30”. The bottom edge

of the template equates to the lower edge

of the hood.

4. Drill 2x

” ø holes for the upper ﬁxing

bracket and

” ø holes for the lower ﬁxing bracket

and press in wall plugs ﬂush with the

wall.

Note: At least one screw for the mounting

must be installed through a stud.

INSTALLATION

6. Attach the hood.

Adjust the height and align horizontally

with the adjusting screws.

Note: Take into account any special

accessories that are going to be ﬁtted.

5. Attach the 2 enclosed spacers to the

ﬁxing bracket for the ﬂue duct panelling.

Attach the ﬁxing bracket for the

chimney panelling using two hexagon

head cap screws.

13. Insert the cover panels at an angle and

tilt them back.

14. Slide out the upper section and attach

it to the mounting brackets at the sides

with two screws.

15. Insert the grease ﬁlter (refer to

Operating Instructions).

If the vent system does not operate

satisfactorily during any of the above

procedures, review all steps in these

Installation Instructions to ensure that

nothing has been omitted or overlooked.

Also, refer to the Care & Use Manual for

additional information or call Thermador

Customer Support 1-800-735-4328.

07. Screw in lower screws (hex screws).

08. Stick protective ﬁlm over the holes of

the 2 lower mounting bolts in the

protective grid.

09. Connect up the air outlet pipe.

10. Connect the hood to the electricity

supply.

11. Remove the protective ﬁlm from the

two ﬂue ducts.

 Take care not to damage the

surfaces which are susceptible to

scratches etc.

Warning: The interior walls of the ﬂue

panelling can have sharp edges – Risk of

injury –.

We recommend that you wear gloves when

installing.

12. Push both sections of the ﬂue panelling

together (slots in the upper section

must be pointing downwards) and

insert into the opening in the hood.

 Protect the cover panels from

scratches, for example by laying the

template used for marking the wall over

the top edge of the lower section.

INSTALLATION

Page is loading ...

9000 333 896

Printed in Germany 0208 Es.

5551 McFadden Avenue, Huntington Beach, CA 92649 • 1-800-735-4328 • www.thermador.com

Thermador HMCN36FS User manual

Brand: Thermador

Model: HMCN36FS

Category: Cooker hoods

Type: User manual

This manual is also suitable for

HMCN42FS

Some of the key features of the Thermador HMCN36FS ventilation hood include:

36-inch width to accommodate most cooktops
4-speed fan to adjust the airflow to your needs
LED lighting to illuminate the cooktop

Download PDF

report

in other languages

français: Thermador HMCN36FS Manuel utilisateur
español: Thermador HMCN36FS Manual de usuario

Thermador HMCN36FS User manual

This manual is also suitable for

Thermador HMCN36FS User manual

in other languages

Related papers

Other documents