Thermador HPIN48HS Installation guide

Brand: Thermador

Model: HPIN48HS

Type: Installation guide

This manual is also suitable for

HPIB42HS

Page is loading ...

READ AND SAVE THESE

INSTRUCTIONS

WARNING – If the information in this

manual is not followed exactly, fire or shock

may result causing property damage or

personal injury.

WARNING – Do not repair or replace

any part of the appliance unless specifically

recommended in the manuals. Improper

installation, service or maintenance can

cause injury or property damage. Refer to

this manual for guidance. All other servicing

should be done by a qualified technician.

Unit is heavy and requires at least two peo-

ple or proper equipment to move.

Hidden surfaces may have sharp edges.

Use caution when reaching behind or under

appliance.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the

event of an electrical short circuit, groun-

ding reduces the risk of electric shock by

providing an escape wire for the electric

current. This appliance is equipped with a

cord having a grounding wire with a

grounding plug. The plug must be plugged

into an outlet that is properly installed and

grounded.

WARNING – Improper grounding can

result in a risk of electric shock.

Consult a qualified electrician if the

grounding instructions are not completely

understood, or if doubt exists as to whether

the appliance is properly grounded.

Do not use an extension cord. If the power

supply cord is too short, have a qualified

electrician install an outlet near the

appliance.

Before you plug in an electrical cord, be ure

all controls are in the OFF position.

For appliances equipped with a cord and

plug, do not cut or remove the ground

prong. It must be plugged into a matching

grounding type receptacle to avoid

electrical shock. If there is any doubt as to

whether the wall receptacle is properly gro-

unded, the customer should have it

checked by a qualified electrician.

If required by the National Electrical Code

(or Canadian Electrical Code), this

appliance must be installed on a separate

branch circuit.

WARNING – To reduce the risk of fire

or electric shock, do not use the fan with

any solid-state speed control device.

Installer - show the owner the location of

the circuit breaker or fuse. Mark it for easy

reference.

Before installing, turn power OFF at the

service panel. Lock service panel to prevent

power from being turned ON accidentally.

WARNING – TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK, OR INJURY

TO PERSONS, OBSERVE THE

FOLLOWING:

a) Use this unit only in the manner intended

by the manufacturer. If you have

questions, contact the manufacturer.

b) Before servicing or cleaning unit, switch

power off at service panel and lock the

service disconnecting means to prevent

power from being switched on

accidentally. When the service

disconnecting means cannot be locked,

securely fasten a prominent warning

device, such as a tag, to the service

panel.



Important Safety Instructions – Installation

Parts Needed

K Tape Measure

K Phillips Head Screwdriver

K Duct Tape

K Ductwork (conﬁguration varies

depending on location; see ”Prior to

installation”).

K Additional Sheetmetal screws

Parts Supplied

K Appliance assembly (1)

K Sheetmetal Screws (6)

K Wood Screws (4)

K Counter Sink Screws (2)

K Hardware for brackets on vent (2)

K Plugs UX6 (6)

Be sure your appliance is properly installed

and grounded by a qualified technician.

Installation, electrical connections and gro-

unding must comply with all applicable

codes.

WARNING – TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK, OR INJURY

TO PERSONS, OBSERVE THE FOLLO-

WING:

a) Installation work and electrical wiring

must be done by authorized person(s) in

accordance with all applicable codes

and standards, including fire-related

construction.

b) Sufficient air is needed for proper

combustion and exhausting of gases

through the flue (chimney) of fuel burning

equipment to prevent back drafting.

Follow the heating equipment

manufacturer’s guideline and safety

standards such as those published by

the National Fired Protection Association

(NFPA), and the American Society for

Heating, Refrigeration and Air Conditio-

ning Engineers (ASHRAE), and the local

code authorities.

c) When cutting or drilling into wall or

ceiling, do not damage electrical wiring

and other hidden utilities.

d) Ducted fans must always be vented to

the outdoors.

Remove all tape and packaging before

using the appliance. Destroy the packaging

after unpacking the appliance.

Never allow children to play with packaging

material.

Never modify or alter the construction of the

appliance. For example, do not remove

leveling legs, panels, wire covers or anti-tip

brackets/screws.

CAUTION – For general ventilating use

only. Do not use to exhaust hazardous or

explosive materials and vapors.

To reduce risk of fire and to properly

exhaust air, be sure to duct air outside. Do

not vent exhaust air into spaces within

walls, ceilings, attics, crawl spaces or

garages.

WARNING – to reduce the risk of fire,

use only metal ductwork.

WARNING – The applicable regulati-

ons of the energy supply companies and

the regional construction regulations must

be observed when installing the hood.

This appliance complies with one or more

of the following Standards:

UL 858, The Standard for the Safety of

Household Electric Ranges

UL 923, The Standard for the Safety of

Microwave Cooking Appliances

UL 507, The Standard for the Safety of

Electric Fans

ANSI Z21.1, The American National

Standard for Household Cooking Gas

Appliances

CAN/CSA-C22.2 No. 113-M1984 Fans and

Ventilators

CAN/CSA-C22.2 No. 61-M89 Household

Cooking Ranges

It is the responsibility of the owner and the

installer to determine if additional

requirements and/or standards apply to

specific installations.



Important Safety Instructions – Installation

ELECTRIC

IMPORTANT INFORMATION

Old appliances are not worthless rubbish.

Valuable raw materials can be reclaimed by

recycling old appliances. Before disposing

of your old appliance, render it unusable.

You received your new appliance in a

protective shipping carton. All packaging

materials are environmentally friendly and

recyclable. Please contribute to a better

environment by disposing of packaging

materials in an environmentally-friendly

manner.

The hood can only be used in exhaust air

mode.

Always mount the hood over the center of

the cooking surface.

 Minimum distance between electric

cooktop and bottom edge of hood: 30”,

Fig. 1.

 The hood must not be installed over a

wood or coal burning stove – a potential ﬁre

hazard (e.g. ﬂying sparks) – unless the

stove features a closed, non-removable

cover and all national regulations are

observed.

The smaller the gap between the hood and

cooktops, the greater the likelihood that

droplets will form on the underside of the

Additional information

concerning gas cookers:

When installing gas cooktops, comply with

the relevant national statutory regulations.

Always comply with the currently valid

regulations and installation instructions

supplied by the gas appliance

manufacturer.

 Only one side of the hood may be

installed next to a high-sided unit or high

wall. Gap at least 2”.

 Minimum distance on gas cooktops

between the upper edge of the grate and

lower edge of the hood: 30”, Fig. 1.

Fig. 1

GAS

≥ 30"≥ 30"

The exhaust air is discharged upwards

through a duct or directly through the

outside wall into the open.

Exhaust air should neither be directed

into a smoke or exhaust ﬂue that is currently

used for other purposes, nor into a duct

that is used for ventilating rooms in which

stoves or ﬁreplaces are also located.

Exhaust air may be discharged in

accordance with ofﬁcial and statutory

regulations only (e.g. national building

regulations).

Local authority regulations must be

observed when discharging air into smoke

or exhaust ﬂues that are not otherwise in

use.

When the hood is operated in

exhaust-air mode simultaneously with a

different burner which also makes use of

the same chimney (such as gas, oil or

coal-ﬁred heaters, continuous-ﬂow heaters,

hot-water boilers) care must be taken to

ensure that there is an adequate supply

of fresh air which will be needed by the

burner for combustion.

Safe operation is possible provided that the

underpressure in the room where the burner

is installed does not exceed 4 Pa (0.04

mbar).

This can be achieved if combustion air can

ﬂow through non-lockable openings, e.g. in

doors, windows and via the air-intake/

exhaust-air wall box.

If the air intake is inadequate, there is a

risk of poisoning from combustion gases

which are drawn back into the room.

 WARNING – Avoid risk of poisoning –

If the air intake to the room is inadequate,

there is a risk of poisoning from combustion

gases which can be drawn back into the

room.

Note: When assessing the overall

requirement, the combined ventilation

system for the entire household must be

taken into consideration. This rule does not

apply to the use of cooking appliances,

such as hobs and ovens.

If the exhaust air is going to be

discharged into the open, a telescopic

wall box should be ﬁtted into the

outside wall.

PRIOR TO INSTALLATION

Step 1: EXHAUST-AIR MODE

42”/48”

- 42

Exhaust Air

Ø 6" Ø 6"

Circulating-air mode

With activated carbon ﬁlter if exhaust-air

For optimum hood efﬁciency:

K Short, smooth duct pipe.

As few bends in the ducting as possible.

Diameter of ducting to be as large as

possible and no tight bends in ducting.

If long, rough exhaust-air ducting,

many ducting bends or smaller pipe

diameters are used, the air extraction

rate will no longer be at an optimum

level and there will be an increase in

noise.

IMPORTANT: The manufacturer of the

hood accepts no liability for

complaints which can be attributed to

the design and layout of the duct-

work.

Round pipes:

We recommend

Internal diameter: 6”.

Flat ducts must have an internal cross-

section that equates to that of round

pipes.

There should be no sharp bends.

l 6” approx. 29 inches

If pipes have different diameters:

Insert sealing strip.

For exhaust-air mode, ensure that

there is an adequate supply of fresh air.

CONNECTING A l 6” EXHAUST-AIR

DUCT:

K Mount the duct directly onto the air out-

let on the hood.

Step 2: PREPARING THE CEILING

K The ceiling must be ﬂat and horizontal.

Make sure that the ceiling can bear the

applied loads.

The provided screws and wall plugs are

suitable for solid masonry. On all other

wall types (e. g. plasterboard, porous

concrete, Poroton bricks) use the appro-

priate fasteners.

Ensure that the ceiling is capable of pro-

viding a ﬁrm hold for mounting screws

and plugs.

Weight in kg: ca. 49

We reserve the right to construction

changes within the context of technical

development.

PRIOR TO INSTALLATION

Ø 6"

42”/48”

" - 42

Recirculating-air

Step 3: ELECTRICAL CONNECTION

 WARNING: THIS APPLIANCE MUST

BE GROUNDED

The hood should only be connected to a

grounded socket that has been installed

according to relevant regulations.

If possible, site the earthed socket directly

behind the chimney paneling.

K The grounded socket should be

connected via its own circuit.

K If the grounded socket is no longer

accessible following installation of the

hood, ensure that there is a permanently

installed disconnector.

Step 4: INSTALL ELECTRICAL

SERVICE

Check your local building codes for proper

method of installation. In the U.S., if there

are no applicable local codes, this unit

should be installed in accordance with the

National Electric Code ANSI/NFPA No. 70,

Current Issue. (In Canada, installation must

be in accordance with the CAN 1- B149.1

and .2 - Installation Codes for Gas Burning

Appliances and/ or local codes).

 CAUTION – To reduce the risk of ﬁre

and electric shock, install this rangehood

only with integral blower or remote blower

manufactured by Thermador rated up to

max. 8,5 A.

 CAUTION – Connect only to a

dedicated branch circuit. Maximum ampere

rating of the rangehood shall not be more

than 80 percent of the branch circuit rating.

The appliance must be grounded. In the

event of an electrical short circuit, grounding

reduces the risk of electric shock by

providing an escape wire for the electric

current. This appliance is equipped with a

cord having a grounding wire with a

grounding plug. The plug must be plugged

into an outlet that is properly installed and

grounded.

 WARNING – Improper grounding can

result in a risk of electric shock.

Consult a qualiﬁed electrician if the

grounding instructions are not completely

understood, or if doubt exists as to whether

the appliance is properly grounded.

Do not use an extension cord. If the power

supply cord is too short, have a qualiﬁed

electrician install an outlet near the

appliance.

If it is necessary to wire the hood directly

into the mains:

The extractor hood should only be

connected to the electricity supply by a

properly qualiﬁed electrician.

 WARNING – Avoid risk of electrical

shock – If the connecting cable for this

appliance is damaged, the cable must be

replaced by the manufacturer or his

customer service or a similarly qualiﬁed

person in order to prevent serious injury to

the user.

ELECTRICAL DATA:

Are to be found on the name plate inside

the appliance after removal of the ﬁlter

frame.

 WARNING – Avoid risk of electrical

shock – Before undertaking any repairs,

always disconnect the hood from the

electricity supply.

Length of the connecting cable: 4 ft.

This hood corresponds to EC regulations

concerning RF interference suppression.

PRIOR TO INSTALLATION

Page is loading ...

Step 5: INSTALLATION

The extractor hood is designed to be

ﬁtted to the kitchen ceiling or a rigid

suspended ceiling.

 CAUTION:

Ensure that the minimum distance

between hotplate and extractor hood is 30”

for electric hotplates and 30” for gas hot-

plates.

1. Mark the centre point of the extractor

hood on the ceiling.

2. Using the template, mark screw

positions on the ceiling.

3. Drill 2x

” ø holes and insert wall plugs

ﬂush with the ceiling.

Note: At least one screw for the

mounting must be installed through a

stud.

INSTALLATION

"-28"

min. 30"

4. Determine the overall height of the

support frame.

– This is the height of the ceiling, the

height of the base and the distance

INSTALLATION

08. Insert the extractor hood over the

installation aids on the support frame.

5. Screw together the upper and lower

sections of the support frame at the

09. Screw the extractor hood to the support

frame and screw back the panel.

6. Screw the support frame to the ceiling

with 4 screws.

INSTALLATION

10. Connect the pipes.

11. Connect the power.

14. Push up the upper ﬂue section and

screw into position.

15. Insert the two sections of the lower ﬂue

and clip together.

 CAUTION:

Protect the extractor hood from

13. Place the two sections of the upper ﬂue

on the extractor hood and clip together.

 CAUTION:

Protect the extractor hood from

Page is loading ...

 AVERTISSEMENT – DÉBRANCHER L'ALIMENTATION AVANT DE RÉPARER CET APPAREIL

Schéma de câblage

Page is loading ...

 ADVERTENCIA: SE DEBE DESCONECTAR LA CORRIENTE ELÉCTRICA ANTES DE REALIZAR EL SERVICIO TÉCNICO A

ESTE APARATO

Diagrama de cableado

Page is loading ...

   



       

       

   

9000 466 407

Printed in Germany 0709 Es.

Thermador HPIN48HS Installation guide

Brand: Thermador

Model: HPIN48HS

Type: Installation guide

This manual is also suitable for

HPIB42HS

Download PDF

report

in other languages

français: Thermador HPIN48HS Guide d'installation
español: Thermador HPIN48HS Guía de instalación

Thermador HPIN48HS Installation guide

This manual is also suitable for

Thermador HPIN48HS Installation guide

in other languages

Related papers

Other documents