American Standard American Standard bath User manual

American Standard
Brand
American Standard
Model
American Standard bath
Category
Space heaters
Type
User manual

This manual is also suitable for

754323-100 Rev A
1
THANK YOU...
for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The Air
Massage System is completely assembled with air pump, motor, lights, and system piping. All you need to
finish the installation are your selected fittings and electrical connections for an Air Massage System.
To insure maximum performance and pleasure from this product, please follow the instructions and cautions.
© AS America, Inc. 2009
All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
GREEN TEA™ 5' x 36" MODEL 3571
GREEN TEA™ 5-1/2' x 36" MODEL 3572
GREEN TEA™ 6' x 36" MODEL 3573
GREEN TEA™ 5' x 42" MODEL 3574
GREEN TEA™ 6' x 42" MODEL 3575
TOWN SQUARE
®
5' x 42" MODEL 2748
TOWN SQUARE
®
6' x 42" MODEL 2742
ELLISSE OVAL MODEL 2709
INSTALLATION GUIDE FOR
COMBINATION WHIRLPOOL AND
AIR BATH SYSTEMS WITH
CHROMATHERAPY LIGHTS
2
754323-100 Rev A
TABLE OF CONTENTS:
Cover
................................................................................................Page 1
Table of Contents
..............................................................................Page 2
Safety Instructions Notice.................................................................Page 3
Roughing-in Reference.....................................................................Page 4 - 12
Installation and Framing Instructions................................................Page 13 - 16
Supplied Drain Assembly and Installation Instructions.....................Page 16 - 20
Post Installation Instructions.............................................................Page 21
Remote Blower Location Option.......................................................Page 22
Warranty
...........................................................................................Page 23
754323-100 Rev A
3
IMPORTANT SAFETY
INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS!
!
!
!
!
!
!
WARNING: Risk of personal injury. Do not permit children to use this bathtub without adult supervision.
WARNING: Risk of electric shock. Do not permit electrical appliances near any bathtub when bathtub contains water.
WARNING: Risk of hyperthermia and possible drowning. People using medications and/or having adverse medical
history should consult a physician before using this product.
WARNING: Risk of personal injury. Do not overfill bathtub before entering. Entering tub when filled more than 2/3 can
cause overflow and slippery conditions. Exercise caution when entering and exiting.
WARNING: No Food or Alcoholic Beverages. Use of your bathtub immediately after meals is not recommended. Avoid
alcohol consumption before or during bathing. Alcoholic beverages can cause drowsiness or hyperthermia resulting in loss of
consciousness or even drowning.
WARNING: Pregnancy. If you are or think you may be pregnant, consult your physician before using the bathtub.
Use this unit only for its intended use as described in this manual. Do not use any attachments not recommended by American
Standard.
The unit must be connected only to a supply circuit that is properly protected by a ground-fault circuit-interrupter (GFCI). Such a
GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button. The
GFCI should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the
GFCI is defective. If the GFCI interrupts power to the bathtub without the test button being pushed, a ground current is flowing,
indicating the possibility of an electric shock. Do not use this air bath. Disconnect the air bath and have the problem corrected by a
licensed electrician before using.
SAVE THESE INSTRUCTIONS
4
754323-100 Rev A
TOP VIEW
END VIEW
GREEN TEA™ 5' x 36"
MODEL 3571 COMBINATION SYSTEM
LEVELING STRINGER NOT
FOR SUPPORT
60
(1524mm)
36
(914mm)
11-1/2
(292mm)
OUTLINE OF CUTOUT 58.5 x 34.5 (1486 x 876mm)
14-3/4
(375mm)
CONTROL PANELS
8 WHIRLPOOL
JETS
CUTOUT IN FLOOR FOR DRAIN
20 AIR JETS
9
(229mm)
C
L
ROUGH
FLOOR
508mm
(20")
INTEGRAL FEET
WITH ATTACHED
BASEBOARD
51mm
(2")
559mm
(22")
C
L
TO OVERFLOW
102mm (4")
ACCESS AIR BLOWER,
PUMP MOTOR,
WHIRLPOOL HEATER
AND LIGHTING SYSTEM
AT THIS END OF TUB
NOTE:
INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR
BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM.
THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES
CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT
TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS.
ROUGHING-IN REFERENCES
754323-100 Rev A
5
TOP VIEW
END VIEW
GREEN TEA™ 5-1/2' x 36"
MODEL 3572 COMBINATION SYSTEM
ROUGHING-IN REFERENCES
22 AIR JETS
66
(1676mm)
36
(914mm)
11-1/2
(292mm)
14-3/4
(292mm)
C
L
CUTOUT IN FLOOR FOR DRAIN
9
(229mm)
OUTLINE OF CUTOUT 64.5 x 34.5 (1638 x 876mm)
CONTROL
PANELS
LEVELING STRINGER NOT
FOR SUPPORT
ROUGH
FLOOR
508mm
(20")
INTEGRAL FEET
WITH ATTACHED
BASEBOARD
51mm
(2")
559mm
(22")
C
L
TO OVERFLOW
102mm (4")
ACCESS AIR BLOWER,
PUMP MOTOR,
WHIRLPOOL HEATER
AND LIGHTING SYSTEM
AT THIS END OF TUB
8 WHIRLPOOL
JETS
NOTE:
INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR
BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM.
THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES
CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT
TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS.
6
754323-100 Rev A
72
(1829mm)
36
(914mm)
11-1/2
(292mm)
OUTLINE OF CUTOUT 70.5 x 34.5 (1780 x 876mm)
14-3/4
(375mm)
CONTROL
PANELS
CUTOUT IN FLOOR
FOR DRAIN
C
L
9
(229mm)
LEVELING STRINGER NOT
FOR SUPPORT
ROUGH
FLOOR
508mm
(20")
INTEGRAL FEET
WITH ATTACHED
BASEBOARD
51mm
(2")
559mm
(22")
C
L
TO OVERFLOW
102mm (4")
23 AIR JETS
ACCESS AIR BLOWER,
PUMP MOTOR,
WHIRLPOOL HEATER
AND LIGHTING SYSTEM
AT THIS END OF TUB
10 WHIRLPOOL
JETS
NOTE:
INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR
BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM.
THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES
CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT
TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS.
TOP VIEW
END VIEW
GREEN TEA™ 6' x 36"
MODEL 3573 COMBINATION SYSTEM
ROUGHING-IN REFERENCES
754323-100 Rev A
7
60
(1524mm)
42
(1067mm)
11-1/2
(292mm)
OUTLINE OF CUTOUT 58.5 x 40.5 (1486 x 1029mm)
14-3/4
(375mm)
C
L
9
(229mm)
CUTOUT IN FLOOR FOR DRAIN
CONTROL
PANELS
LEVELING STRINGER NOT
FOR SUPPORT
ROUGH
FLOOR
508mm
(20")
INTEGRAL FEET
WITH ATTACHED
BASEBOARD
51mm
(2")
559mm
(22")
C
L
TO OVERFLOW
102mm (4")
23 AIR JETS
ACCESS AIR BLOWER,
PUMP MOTOR,
WHIRLPOOL HEATER
AND LIGHTING SYSTEM
AT THIS END OF TUB
8 WHIRLPOOL
JETS
NOTE:
INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR
BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM.
THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES
CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT
TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS.
TOP VIEW
END VIEW
GREEN TEA™ 5' x 42"
MODEL 3574 COMBINATION SYSTEM
ROUGHING-IN REFERENCES
8
754323-100 Rev A
72
(1829mm)
42
(1067mm)
11-1/2
(292mm)
OUTLINE OF CUTOUT 70.5 x 40.5 (1780 x 1029mm)
14-3/4
(375mm)
C
L
9
(229mm)
CUTOUT IN FLOOR FOR DRAIN
LEVELING STRINGER NOT
FOR SUPPORT
ROUGH
FLOOR
508mm
(20")
INTEGRAL FEET
WITH ATTACHED
BASEBOARD
51mm
(2")
559mm
(22")
C
L
TO OVERFLOW
102mm (4")
27 AIR JETS
ACCESS AIR BLOWER,
PUMP MOTOR,
WHIRLPOOL HEATER
AND LIGHTING SYSTEM
AT THIS END OF TUB
NOTE:
INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR
BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM.
THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES
CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT
TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS.
10 WHIRLPOOL
JETS
CONTROL PANELS
TOP VIEW
END VIEW
GREEN TEA™ 6' x 42"
MODEL 3575 COMBINATION SYSTEM
ROUGHING-IN REFERENCES
754323-100 Rev A
9
C/L
FOR SPOUT
& VALVES
FOR HAND
SPRAY
FITTINGS
DECK
EDGE OF
FITTINGS
DECK
29-3/4
(755mm)
TO END OF TUB
1-1/2
(38mm)
1-1/2
(38mm)
1-1/2
(38mm)
2-1/2
(64mm)
4-1/2
(114mm)
4-1/2
(114mm)
5
(127mm)
DRAIN
HOLE DRILLING LOCATION FOR AMERICAN STANDARD "TOWN SQUARE"
DECK MOUNT BATH FILLER WITH PERSONAL SHOWER, MODEL #2555.901 ONLY
59-1/2"
(1511mm)
29-3/4"
(755mm)
41-5/8"
(1057mm)
CONTROL PANELS
OUTLINE OF CUTOUT
58" X 40-1/8"
(1473 X 1019mm)
FLOOR CUTOUT
9" X 18"
(229 X 458mm)
3/4"
(19mm)
14-1/2"
(368mm)
3"
(76mm)
OUTLINE OF
SKID RESISTANT
SURFACE
20 AIR JETS
6 WHIRLPOOL
JETS
LEVELING STRINGER
(NOT FOR SUPPORT)
21"
(533mm)
23"
(584mm)
ROUGH
FLOOR
INTEGRAL FEET WITH
ATTACHED BASEBOARD
7-3/4" TYPICAL
(197mm)
ACCESS AIR BLOWER,
PUMP MOTOR,
WHIRLPOOL HEATER
AND LIGHTING SYSTEM
AT THIS END OF TUB
NOTE:
INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR
BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM.
THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES
CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT
TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS.
INTEGRAL FITTING DECK
2-1/2" X 14"
(64 X 356mm)
TOP VIEW
END VIEW
TOWN SQUARE
®
5' x 42"
MODEL 2748 COMBINATION SYSTEM
ROUGHING-IN REFERENCES
10
754323-100 Rev A
C/L
FOR SPOUT
& VALVES
FOR HAND
SPRAY
FITTINGS
DECK
EDGE OF
FITTINGS
DECK
35-3/4
(908mm)
TO END OF TUB
1-1/2
(38mm)
1-1/2
(38mm)
1-1/2
(38mm)
2-1/2
(64mm)
4-1/2
(114mm)
4-1/2
(114mm)
5
(127mm)
DRAIN
HOLE DRILLING LOCATION FOR AMERICAN STANDARD "TOWN SQUARE"
DECK MOUNT BATH FILLER WITH PERSONAL SHOWER, MODEL #2555.901 ONLY
CONTROL
PANELS
41-3/4"
(1060mm)
26-3/4
(679mm)
7-3/4” TYPICAL
(197mm)
OUTLINE OF SKID
RESISTANT SURFACE
35-3/4"
(908mm)
13-1/4"
(337mm)
71-1/2"
(1816mm)
3"
(76mm)
FLOOR CUTOUT
9" X 19"
(229 X 459mm)
OUTLINE OF CUTOUT
70" X 40-1/4" (1778 X 1022mm)
INTEGRAL
FITTING DECK
2-1/4" X 14"
(57 X 356mm)
3/4"
(19mm)
EDGE OF
FLOOR
CUTOUT
AIR
BLOWER
20 AIR
JETS
LEVELING STRINGER
(NOT FOR SUPPORT)
2"
(51mm)
3-1/4"
(83mm)
20"
(508mm)
22"
(559mm)
ROUGH
FLOOR
10-1/4”
(260mm)
INTEGRAL FEET WITH
ATTACHED BASEBOARD
8 WHIRLPOOL
JETS
ACCESS AIR BLOWER, PUMP
MOTOR, WHIRLPOOL HEATER
AND LIGHTING SYSTEM AT
THIS END OF TUB
NOTE:
INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR
BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM.
THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES
CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE DOCUMENT
TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS.
TOP VIEW
END VIEW
TOWN SQUARE
®
6' x 42"
MODEL 2742 COMBINATION SYSTEM
ROUGHING-IN REFERENCES
754323-100 Rev A
11
FLOOR CUTOUT
229 X 459mm
(9" X 19")
1759 mm
(69-1/4")
OUTLINE OF
CUTOUT
240 mm
(9-7/16")
978 mm
(38-1/2")
489mm
(19-1/4")
16 AIR
JETS
6 WHIRLPOOL
JETS
CONTROL
PANELS
7-3/4" TYPICAL
(197mm)
ROUGH
FLOOR
495mm
(19-1/2")
INTEGRAL FEET
WITH ATTACHED
BASEBOARD
86mm (3-3/8")
38mm
(1-1/2")
533mm
(21")
C
L
TO OVERFLOW
ACCESS AIR BLOWER, PUMP MOTOR,
WHIRLPOOL HEATER AND LIGHTING
SYSTEM AT THIS END OF TUB
NOTE:
INSTALLER MUST PROVIDE 12 X 24 ACCESS OPENING FOR SERVICING AIR
BLOWER, PUMP MOTOR, WHIRLPOOL HEATER, AND LIGHTING SYSTEM.
THIS MODEL INCLUDES A DRAIN ASSEMBLY. OTHER DRAIN ASSEMBLIES
CANNOT BE USED. REVIEW DRAIN INSTALLATION DETAILS IN THE
DOCUMENT TO FULLY UNDERSTAND FLOOR CUTOUT REQUIREMENTS.
TOP VIEW
END VIEW
ELLISSE OVAL
MODEL 2709 COMBINATION SYSTEM
ROUGHING-IN REFERENCES
12
754323-100 Rev A
ROUGHING-IN REFERENCES
GENERAL SPECIFICATIONS FOR 2748
COMBINATION SYSTEM
59-1/2 x 41-5/8 x 23 In. (1511 x 1057 x 584mm)
110 Lbs. (50 Kg.)
611 Lbs. (278 Kg.)
60 Gal. (227 L)
34 x 24 In. (864 x 610mm)
52 x 31 In. (1321 x 1321mm)
12-1/2 In. (318mm)
29 Lbs./Sq.Ft. (144 Kgs./Sq.m)
27.8
45.4
ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
GENERAL SPECIFICATIONS FOR 2709
COMBINATION SYSTEM
69-1/4 x 38-1/2 x 19-3/4 In.(1759 x 978 x 502mm)
119 Lbs. (54 Kg.)
652 Lbs. (296 Kg.)
64 Gal. (243 L)
45 x 23 In. (1143 x 584mm)
63 x 32 In. (1600 x 813mm)
13 In. (330mm)
35 Lbs./Sq.Ft. (172 Kgs./Sq.m)
25.6
49.4
ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
GENERAL SPECIFICATIONS FOR 2742
COMBINATION SYSTEM
71-1/2 x 41-3/4 x 22 In. (1816 x 1060 x 559mm)
174 Lbs. (79 Kg.)
830 Lbs. (313 Kg.)
69 Gal. (261 L)
41 x 21-1/2 In. (1041 x 546mm)
62 x 31-1/2 In. (1574 x 800mm)
14-1/4 In. (362mm)
36 Lbs./Sq.Ft. (176 Kgs./Sq.m)
27.8
55.7
ELECTRICAL SPECIFICATIONS
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
60 x 36 x 22 In. (1524 x 914 x 559mm)
117 Lbs. (53 Kg.)
550 Lbs. (250 Kg.)
52 Gal. (197 L.)
38 Gal. (144 L.)
19 x 43 In. (483mm x 1092mm)
48-1/2 x 27 In. (1232mm x 686mm)
14 In. (356mm)
37 Lbs./Sq. Ft. (179 Kgs/Sq. m.)
23.8
44.5
GENERAL SPECIFICATIONS FOR 3571
COMBINATION SYSTEM
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
ELECTRICAL SPECIFICATIONS
66 x 36 x 22 In. (1676 x 914 x 559mm)
128 Lbs. (58 Kg.)
619 Lbs. (281 Kg.)
59 Gal. (223 L.)
44 Gal. (167 L.)
19 x 49 In. (483mm x 1245mm)
54-1/2 x 27 In. (1384mm x 686mm)
14 In. (356mm)
38 Lbs./Sq. Ft. (188 Kgs/Sq. m.)
25.6
45.1
GENERAL SPECIFICATIONS FOR 3572
COMBINATION SYSTEM
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
ELECTRICAL SPECIFICATIONS
72 x 36 x 22 In. (1829 x 914 x 559mm)
143 Lbs. (65 Kg.)
693 Lbs. (314 Kg.)
66 Gal. (250 L.)
49 Gal. (185 L.)
19 x 55 In. (483mm x 1397mm)
60-1/2 x 27 In. (1537mm x 686mm)
14 In. (356mm)
38 Lbs./Sq. Ft. (188 Kgs/Sq. m.)
23.8
44.5
GENERAL SPECIFICATIONS FOR 3573
COMBINATION SYSTEM
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
ELECTRICAL SPECIFICATIONS
59-3/4 x 42 x 22 In. (1518 x 1060 x 559mm)
141 Lbs. (64 Kg.)
682 Lbs. (310 Kg.)
65 Gal. (246 L.)
47 Gal. (178 L.)
24-1/2 x 42 In. (622mm x 1067mm)
48 x 33 In. (1219mm x 838mm)
14 In. (356mm)
39 Lbs./Sq. Ft. (192 Kgs/Sq. m.)
27.8
47.4
GENERAL SPECIFICATIONS FOR 3574
COMBINATION SYSTEM
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
ELECTRICAL SPECIFICATIONS
72 x 42 x 22 In. (1829 x 1067 x 559mm)
172 Lbs. (78 Kg.)
830 Lbs. (377 Kg.)
79 Gal. (299 L.)
58 Gal. (219 L.)
22-1/2 x 54 In. (572mm x 1372mm)
60 x 33 In. (1524mm x 838mm)
14 In. (356mm)
40 Lbs./Sq. Ft. (193 Kgs/Sq. m.)
25.6
49.4
GENERAL SPECIFICATIONS FOR 3575
COMBINATION SYSTEM
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
ELECTRICAL SPECIFICATIONS
ELLISSE OVAL
MODEL 2709 COMBINATION SYSTEM
TOWN SQUARE
®
5' x 42"
MODEL 2748 COMBINATION SYSTEM
REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14
TOWN SQUARE
®
6' x 42"
MODEL 2742 COMBINATION SYSTEM
GREEN TEA™ 5' x 36"
MODEL 3571 COMBINATION SYSTEM
GREEN TEA™ 6' x 36"
MODEL 3573 COMBINATION SYSTEM
GREEN TEA™ 5' x 42"
MODEL 3574 COMBINATION SYSTEM
GREEN TEA™ 5-1/2' x 36"
MODEL 3572 COMBINATION SYSTEM
GREEN TEA™ 6' x 42"
MODEL 3575 COMBINATION SYSTEM
•
•
•
•
•
•
•
•
REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14
•
REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14
•
REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14
•
REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14
•
REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14
•
REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14
•
REFER TO ELECTRICAL INSTALLATION DIAGRAM ON PAGE 14
•
•
754323-100 Rev A
13
INSTALLATION AND FRAMING INSTRUCTIONS:
The variety of installations possible for this combination system may require framing procedures
other than those shown. Locate studs as required. Ensure roughing-in dimensions are proper,
plumb and square. Provisions must be made in all installations for an access opening for servicing
the air blower and controls. It is strongly recommended that an additional opening be provided for
access to the drain components. The apron should not be used as the primary access opening.
1. Position the combination system into the installation opening and level the deck in both
directions, shimming the integral feet with attached baseboard as necessary. Refer to the
Combination Installation Table for nominal installation dimensions. Mark the final position of
the underside of the deck by tracing a line on to the studs (see Figure 1).
2. Remove the air massage system and attach a 1 x 4 stringer to the studs, with the top of the
stringer touching the traced line.
The rim of the bath must not support weight.
TYPICAL PIER TYPE INSTALLATION
AS DESIRED
F
CUTOUT
AS DESIRED
E
CUTOUT
D
24
(610 mm)
12
(305 mm)
MOUNTING
SURFACE
WATERPROOF
SEALANT
BATH
TYPICAL RECESS INSTALLATION
24
(610 mm)
12
(305 mm)
D
A
B
C
LEVELING
STRINGERS
TILE
TILE
BEAD
STRIP
LEVELING STRINGER
1 x 4 (not for support)
BATH
ADHESIVE
SEALANT
WALLBOARD
NOTE: Tile bead kit not included
and must be purchased separately.
D
TYPICAL
INSTALLATION
FIGURE 1
3. Install supplied cable drain components to the combination system according to the enclosed drain installation
instructions. Before replacing your bath for final installation, be certain that an opening has been provided in the
sub-floor for the drain. See the roughing-in drawing for suggested opening size (shadowed) and location
dimensions. The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout
in the floor.
4. Replace combination system and re-shim the integral support feet with attached baseboard, shimming the entire
length of the baseboard as needed. Secure the shims using construction adhesive, silicone or equivalent
materials.
The rim of the bath must not support weight. Any finish material such as tile or wall board must be
self-supporting if it contacts the deck of the bath.
!
!
ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE MOTOR.
ALLOW OPEN FRAMING ON PUMP/MOTOR
END FOR SERVICE.
ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE BLOWER.
ALLOW OPEN FRAMING ON
BLOWER END FOR SERVICE.
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
NOTE:
FRONT EDGE
OF BATH MUST
BE SUPPORTED
BY STUD WALL OR
AMERICAN STANDARD
APRON KIT
** USE CUTOUT TEMPLATE PROVIDED FOR 2709 MODEL
NOTICE:
DO NOT BUILD THE SURROUNDING STRUCTURE BEFORE RECEIVING YOUR AIR BATH.
STRUCTURE MEASUREMENTS SHOULD BE VERIFIED AGAINST THE ACTUAL AIR BATH
RECEIVED TO ENSURE PROPER FIT.
60-1/4"
35"
36"
19"
58-1/2"
34-1/2"
1530mm
889mm
914mm
483mm
1486mm
876mm
66-1/4"
35"
36"
19"
64-1/2"
34-1/2"
1683mm
889mm
914mm
483mm
1638mm
876mm
72-1/4"
35"
36"
19"
70-1/2"
34-1/2"
1835mm
889mm
914mm
483mm
1791mm
876mm
60"
40-3/4"
41-3/4"
19"
58-1/4"
40-1/4"
1524mm
1035mm
1060mm
483mm
1480mm
1022mm
72-1/4"
41"
42"
19"
70-1/2"
40-1/2"
1835mm
1041mm
1067mm
483mm
1791mm
1029mm
COMBINATION INSTALLATION TABLE
DIM.
DESCRIPTION
A
B
C
D
E
F
59-3/4"
39-3/4"
41-3/4"
21"
58"
40-1/8"
1518mm
1511mm
1060mm
533mm
1473mm
1019mm
Nominal tub length recess opening
Nominal tub apron support opening
Nominal tub width recess opening
Nominal tub height opening
Nominal tub length cutout
Nominal tub width cutout
71-3/4"
39-3/4"
41-3/4"
20"
70"
40-1/4"
1823mm
1511mm
1060mm
508mm
1778mm
1022mm
19-1/2"
67"
36-1/2"
495mm
1702mm
927mm
**
2748 2742
COMBINATION MODEL NUMBER
2709
3571
3572 3573 3574 3575
14
754323-100 Rev A
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes.
WARNING: When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK! Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Permit access for servicing motor as noted.
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).
ELECTRICAL INSTALLATION INSTRUCTIONS
This installation requires 3 separate 120VAC dedicated circuits with GFCI (Ground Fault Circuit Interrupter) protection as
shown in Figure 2. Two of the three GFCI outlets MUST be 20AMP service.
At initial start-up with the power ON, push the GFCI test button. The reset button should pop out. Push this button in to reset.
If the GFCI fails to operate in the manner, there is a ground fault or malfunction, indicating the possibility of electrical shock.
Turn off the power and do not use until the source of the problem has been identified and corrected.
FIGURE 2: ELECTRICAL INSTALLATION DIAGRAM
!
BLACK
WHITE
120 VAC
GND.
BLACK
WHITE
120 VAC
GND.
BLACK
WHITE
120 VAC
GND.
20A GFCI OUTLET 20A GFCI OUTLET 15A GFCI OUTLET
“WHIRLPOOL WITH 2 LIGHTS”
CONFIGURATION
“AIR BATH”
CONFIGURATION
WHIRLPOOL TEE HEATER
POWER
DISTRIBUTION
BOX
AIR BLOWER
120V @ 10A MAX
WHIRLPOOL PUMP
120V @ 15A MAX
2 LIGHTS
120V @ 1A
WHIRLPOOL HEATER
120V @ 13A MAX
754323-100 Rev A
15
ELECTRICAL INSTALLATION INSTRUCTIONS
(continued)
WHIRLPOOL HEATER OPERATION
Ensure the heater and pump are properly GROUNDED
and BONDED as required. Attach the 8 AWG solid
copper conductor supplied with the heater from the
heater bonding lug to the motor frame bonding lug as
shown in Figure 3.
The conductor is secured to the lugs using set screws.
The motor frame shall have a second 8 AWG solid
copper conductor connected from the frame bonding
lug to the home’s electrical panel or approved local
bonding point as shown in Figure 3.
RUN 8 AWG SOLID COPPER
CONDUCTORS FROM
HEATER BONDING LUG TO
PUMP/MOTOR FRAME LUG
AND FROM PUMP/MOTOR
LUG TO APPROVED
GROUND AS SHOWN
(PUMP/MOTOR)
TO GROUND
SECOND
COPPER
CONDUCTOR
FIRST COPPER
CONDUCTOR
PUMP/MOTOR FRAME WITH
BONDING LUGS
HEATER ON
E-Z INS
TAL
L
™
WHIR
L
POOL
HE
A
T
E
R
(HEATER)
FIGURE 3: GROUNDING DIAGRAM
FIGURE 4: WHIRLPOOL HEATER
INDICATOR LIGHT
WARNING: Prior to operation, review the Important Safety
Instructions listed at the beginning of this instruction manual.
Once the heater is installed and the whirlpool pump is operating,
the heater is totally automatic. The heater will help maintain the
temperature of the water in the bath.
Pressure Switch
The heater is equipped with a preset pressure switch. The pump
must be running with water flowing in the whirlpool to allow the
heater to turn on.
Indicator Light
This light turns on whenever the heater is operating.
High-Limit Switch
The heater includes an exclusive "Intelligent High-Limit". This safety circuit will not "false trip" from hot tap water.
It will only turn the heater off if the thermostat fails. If the high-limit trips frequently, call a service technician.
To manually reset the circuit in the event that the “High-Limit” switch has been activated, simply
(1) Turn off the whirlpool pump.
(2) Drain water from the tub.
(3) Remove power from heater by unplugging at receptacle or turning off circuit breaker.
(4) The heater circuit will automatically reset in less than 15 minutes.
(5) Restore power to the heater.
(6) Whirlpool bath is now ready to use.
HEATER “ON” LIGHT
Bonding Lug on
Heater Housing
E-Z INSTALL
™
WHIRLPOOL
HEATER
FACTORY INSTALLED - NOT FOR RESALE
HEATER P/N: 753174-100
16
754323-100 Rev A
Please note that care must be taken to protect the surface of the tub during all aspects of the installation.
Do not drill or cut the bath deck with the tub directly beneath it as damage to the tub may result.
1. Install the tub per the installation instructions provided with the unit.
2. Prepare the bath deck support structure per the local codes. Note - the bath deck must be self supporting.
3. Cut bath deck to your specifications.
4. Place the bath deck in position and trace the opening on the tub with a soft pencil. Do not drill or cut the bath
deck with the tub directly beneath it as damage to the tub may result.
5. Remove the bath deck and apply a generous bead of waterproof sealant on the outer edge of the traced line.
6. Replace the bath deck and secure it into place.
7. Apply additional sealant along the tub and bath deck interface as necessary to ensure a watertight seal.
8. Remove excess sealant per the manufacturer's instructions.
Finished bath deck surface material must be
self-supporting and secured per local codes
Tub support structure per installation
instructions provided with the tub
Bath deck support material
Bathtub
Waterproof
Sealant
UNDER DECK MOUNTING INSTRUCTIONS
DRAIN STOPPER
WITH
ADJUSTABLE
BOLT
METAL STRAINER
BOLT
METAL
STRAINER
FLAT RUBBER
GASKET
DRAIN WASTE
FLANGE
OVERFLOW
ASSEMBLY
OVERFLOW NUT WITH O-RING
OVERFLOW
ESCUTCHEON
PLASTIC DRAIN BASE
DRAIN ACTUATOR SHAFT
SET
SCREW
AIR BATH NUT
WITH WASHER
AND GASKET
OVERFLOW
RETAINER
WEDGE
GASKET
CLOSE
OPEN
OVERFLOW
ASSEMBLY
VERTICAL
DRAIN PIPE
HORIZONTAL
DRAIN PIPE
PLASTIC
DRAIN BASE
90˚ ELBOW
AIR BATH DRAIN ILLUSTRATION
With supplied cable drain assembled to
bath, connect drain outlet to waste line in
accordance with the drain assembly
instructions. Tighten all drain joints
securely. Check the couplings and make
sure they are hand-tight. Clean the air
bath and fill with water to a point 2" below
the overflow. Recheck the couplings and
make certain that they are not leaking.
(Although the couplings are factory
tightened and inspected, some loosening
may have occurred during transit.) Make
sure the air bath is connected to the
electrical supply and turn the air bath on.
Check for leaks around all piping
connections while the air bath is running.
DRAIN CONNECTION AND
SYSTEM TEST
(before installing bath into
framed out structure)
754323-100 Rev A
17
%3"*/$0//&$5*0/
3FNPWFBOEJEFOUJGZBMMESBJODPNQPOFOUTBTEFGJOFEJOBJSCBUIESBJOJMMVTUSBUJPO
'JOETDIFEVMF17$QJQFMFOHUI)03*;0/5"-%3"*/1*1&
$VUQJQFUPOPNJOBMMFOHUIBOENBSLBTiIPSJ[POUBMQJQFuESBJOUPFMCPXTFDUJPO
'JOEEJBNFUFS7&35*$"-'-&91*1&.BSLBTiWFSUJDBMQJQFu
ESBJOUPFMCPXTFDUJPO
*OTUBMMESBJOGSPNCFMPXVOJUUISPVHIPQFOJOHBTTIPXOJOQIPUP"
"QQMZPSQFBTJ[FEEBCTPGTJMJDPOFTFBMBOUUPCPUUPNXBTUFESBJOGMBOHFBOEQSFTTGMBUSVCCFSHBTLFUJOUPQMBDF
BTTIPXOJOQIPUPT#BOE$
"QQMZDPOUJOVPVTCFBEPGTJMJDPOFTFBMBOUUPGMBUSVCCFSHBTLFUBTTIPXOJOQIPUP%4FUBTJEFBOECFTVSFOPUUP
EJTUVSCTJMJDPOFCFBE
"QQMZDPOUJOVPVTCFBEPGTJMJDPOFTFBMBOUUPCBDLTJEFUPNFUBMTUSBJOFSBTTIPXOJOQIPUP&1SFTT
4USBJOFSSFUBJOJOHCPMUJOUPNFUBMTUSBJOFSBOEJOTFSUJOUPESBJOIPMFPGBDSZMJDCBUI
"
#
$
%
&
18
754323-100 Rev A
%3"*/$0//&$5*0/DPOUJOVFE

)BWFBTTJTUBOUUBLFESBJOBTTFNCMZGSPNTUFQBOEQMBDFPWFSCBDLTVSGBDFPGESBJOIPMFUPFOHBHFUIFNFUBMTUSBJOFSCPMU
4FDVSFQMBTUJDESBJOCBTFUPNFUBMTUSBJOFSJOESBJOPQFOJOHVTJOHOVUESJWFSTIBGU%0/0507&35*()5&/$BSFGVMMZ
SFNPWFFYDFTTTJMJDPOFGSPNBDSZMJDTVSGBDFBTEJSFDUFECZTJMJDPOFTFBMBOUEJSFDUJPOT
'SPNVOJUCBDLTJEFPWFSGMPXOVUTIPVMECFJOBMJHONFOUXJUIPWFSGMPXPQFOJOHBTTIPXOJOQIPUP'
4MJEFBJSCBUIGJUUJOHOVUXBTIFSBOEHBTLFUPOUPBJSCBUIGJUUJOHBTTIPXOJOQIPUPT(BOE)
"TTFNCMFBJSCBUIGJUUJOHUPQMBTUJDESBJOCBTFBTTIPXOJOQIPUPT*+,BOE-)BOEUJHIUFOOVUUPDSFBUFXBUFSUJHIUKPJOU
"QQMZ17$DFNFOUUP)PSJ[POUBM%SBJO1JQF17$BOEBTTFNCMFUPEFHSFFFMCPX
'
( )
*
+
,
-
0WFSGMPXOVU
0SJOH
"JSCBUI
GJUUJOH
754323-100 Rev A
19
.
/
0
1 2 3
%3"*/$0//&$5*0/DPOUJOVFE

%JTBTTFNCMFPWFSGMPXXFEHFHBTLFUBOEDISPNFPWFSGMPXSFUBJOFSBTTIPXOJOQIPUP.
1MBDFPWFSGMPXXFEHFHBTLFUPOUPQMBTUJDPWFSGMPXQJQFGMBOHFXJUISPVOESBJTFESJCTVSGBDFDPOUBDUJOHGMBOHF
BTTIPXOJOQIPUP/
5JHIUFODISPNFPWFSGMPXSFUBJOFSPOUPESBJOPWFSGMPXBTTFNCMZQJQFQFSQIPUP0
"QQMZ17$DFNFOUUPCBSCFEFOEPGEFHSFFFMCPXBOEJOTFSUWFSUJDBMGMFYIPTFPWFSCBSCTBTTIPXOJOQIPUP1

"MJHOWFSUJDBMGMFYIPTFFOEPGQJQJOHXJUIUPQPGCBSCFEGJUUJOHMPDBUFEPOUIFPWFSGMPXGJUUJOHBOENBSLUIFGMFYIPTF
UPCFUSJNNFEBTTIPXOJOQIPUP2
$VUPGGFYDFTTWFSUJDBMGMFYIPTFBTTIPXOJOQIPUP3
"UUBDIWFSUJDBMGMFYIPTFUPCBSCFEGJUUJOHPOPWFSGMPXGJUUJOHCZQSFIFBUJOHUVCJOHBOEPSTPBQJOHCBSCFEGJUUJOHXJUI
EJTITPBQBTTIPXOJOQIPUP4
4
20
754323-100 Rev A
%3"*/$0//&$5*0/DPOUJOVFE

"MJHOGMBUPOESBJOBDUVBUPSTIBGUXJUIDPSSFTQPOEJOHGMBUJODISPNFNFUBMPWFSGMPXFTDVUDIFPOBOEUJHIUFOTFUTDSFXUPGJY
PWFSGMPXFTDVUDIFPOJOQMBDFQFSQIPUPT5BOE6
3PUBUFMFGUBOESJHIUMJHIUMZUPGFFMTUPQTJOESBJODBCMFDPOUSPM5IJTPQFOTBOEDMPTFTESBJO
1MBDFESBJOTUPQQFSJOUPESBJOXBTUFIPMFBTTIPXOJOQIPUP7
5IFESBJOTUPQQFSTIPVMEQSFWFOUXBUFSGSPNESBJOJOHPVUPGUVCXIFOUIFFTDVUDIFPOJTJOUIFGVMMZDPVOUFSDMPDLXJTF
QPTJUJPOBTTIPXOJOQIPUP8"EKVTUUIFESBJOTUPQQFSCPMUUPPCUBJOUIFCFTUXBUFSTFBMJOUIFUVC
3PUBUF%SBJO&TDVUDIFPOUPDMPDLXJTFTUPQ5IJTTIPVMEPQFOESBJOCFUXFFOBOEUPBMMPXXBUFSUPFYJUCBUI
*GOPUBEKVTUNFUBMCPMUJOESBJOTUPQQFSUPBMMPXESBJOJOHGVODUJPOCVUOPUTPIJHIUIBUESBJOXJMMOPUTFBMXIFODMPTFEUP
IPMEXBUFSEVSJOHVTF4FFQIPUP9
5
8
6
9
7
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

American Standard American Standard bath User manual

American Standard
Brand
American Standard
Model
American Standard bath
Category
Space heaters
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents