American Standard 1748102.222 Installation guide

American Standard
Brand
American Standard
Model
1748102.222
Category
Water pumps
Type
Installation guide

This manual is also suitable for

THANK YOU...
for selecting an American Standard bath. Your new bath is shipped to you
after careful inspection. the whirlpool version is completely assembled with
pump, motor, and system piping. All you need to finish the installation are
your selected fittings and electrical connections for a whirlpool. To insure
maximum performance and pleasure from this product, please follow the
instructions and cautions.
General Installation Information
Carefully uncrate and inspect your new bath for any shipping damage. If
such damage is found, report it to your vendor immediately. After inspection
and during installation, protect the bath from construction damage. Before
installation, and before enclosing with wallboard, tile, etc., water test
the unit and check for leaks. Do not make modifications to the whirlpool
system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not
handle or move the whirlpool by the pump, motor, or piping system. Fittings
(bath filler, shower arm, etc.) are not provided with the bath and must be
ordered separately. Framing and enclosing materials are provided by others.
753449-100 Rev. C
© AS America Inc. 2010
All product names listed herein are trademarks
of AS America Inc. unless otherwise noted.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
General Installation Information
Bath may only be installed in a recess type installation.
Locate studs as required. insure rough dimensions are proper, plumb and square. For whirlpools, access to pump/motor may be made through access
opening in apron panel. The following procedure must be used for all installations: leveling support stringer should be as indicated. this bath is not
self-supporting and must be supported along it's entire bottom. Support with mortar or grout. Position bathtub/whirlpool within the recess, check level, front
to back, side to side, and shim as necessary. To secure the tub to wood studs use drywall screws w/washers or roofing nails immediately above the flange
of the tub. To secure the tub to steel studs use 4" drywall screws and flatwashers.
See page 2 for complete installation information.
Caution: Take extra care when driving nails or screws to avoid damaging the tub. The tile or similar finished floor will be butted against the bottom of
the tub apron, also holding the tub in place.
IMPORTANT: Water test unit before installation and
enclosure!
List of Optional Components (not included):
• Metal Air Control Kit 9850.200*
• Jet Trim Ring Kit 9860.200*
List of Required Components (not included):
• Drain 1583.470* • Bath Filler*
* see your American Standard Dealer
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFI
Outlet
• Cement, Plaster,
Grout
Left-hand version shown
66" (1676mm)
WATER RETENTION
FLANGE (3 SIDES)
FINISHED
WALL
7-1/4" (184mm)
C/L OF DRAIN
3/4" (19mm)
15-1/2"
(394mm)
32"
(813mm)
1-1/2"
(38mm)
C/L OF
SUPPLIES
2-3/8" ± 1/2"
(60 ± 13mm)
C/L OF DRAIN
OUTLET
19-1/4"
(489mm)
1" WATER
RETENTION
FLANGE
(3 SIDES)
19-1/2"
(495mm)
1-1/2" O.D.TAILPIECE
BATH
SUPPORT
MATERIAL
ROUGH
FLOOR
FINISHED
WALL
TOP OF
DECK
3-1/4"
(83mm)
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
65" & 78"
(1651 & 1981mm)
C/L OF
OVERFLOW
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
2-3/4"
(70mm)
4-5/8"
(117mm)
1-1/2" N.P.T.M.
THREADS
UNDERSIDE
OF DECK
ON/OFF SWITCH
PUMP
12"
(305mm)
OPT.
4
"
(102mm)
LEVELING
STRINGER
NOT FOR
SUPPORT
TILING
FLANGE
66 x 32 x 19-1/2 In.(1676 x 813 x 495mm)
120 Lbs. (54 Kg.)
537 Lbs. (244 Kg.)
50 Gal. (189 L.)
46 Gal. (174 L.)
18 x 48 In. (457 x 1219mm)
26 x 59 In.(660 x 1499mm)
12-1/2 In. (318 mm)
37 Lbs./Sq. Ft. (179 Kgs/Sq. m.)
20.8
35.3
GENERAL SPECIFICATIONS FOR 1748 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.25 HP, 9.9 AMPS, 120V.SYSTEM I PUMP
INTEGRAL APRON WITH
REMOVABLE ACCESS PANEL
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
COLONY™ 5-1/2'
INSTALLATION
INSTRUCTIONS
1748 SERIES WHIRLPOOL / BATHING POOL
753449-100 Rev. C (2)
INSTALLATION AND FRAMING INSTRUCTIONS
Locate studs as required. Ensure roughing-in dimensions are proper, plumb and square. Access to Pump/Motor may be made through
the access opening in the apron panel. It is strongly recommended that an additional opening be provided for access to the drain
components.
NOTE: The apron may be used as the primary access opening.
1. As shown in Fig. 1, mark the position of the underside of the deck by tracing a line onto the studs, using a level or other suitable
straight edge.
2. With the top of the stringer touching the traced line, attach the stringer to the studs.
NOTE: Cut a 1/2" deep notch into the stringer to accommadate the air control (see Fig. 4).
3. Install drain components to the whirlpool or bath following the manufacturers instructions. See the roughing-in drawing for suggested
opening size and location dimensions.
4. THIS BATH MUST BE SUPPORTED ALONG ITS ENTIRE BOTTOM. We recommend the use of mortar as bedding material (sand
is not recommended). Apply enough bedding to support the complete bottom of the bath. After the bedding has been poured, and
before it sets, position whirlpool or bath within recess until the rim is leveled against the leveling stringers (see "Typical Recess
Installation") shown below. The rim of the bath MUST NOT support weight. Allow the bedding material to completely harden before
applying weight to the rim or bottom of the bath. Any finish material such as tile or wall board must be self-supporting if it contacts
the deck of the bath.
19-1/4"
(489mm)
FIG. 1
FIG. 3
FIG. 2
TYPICAL RECESS INSTALLATION FRAMING FOR LEFT HAND TUB SHOWN
34" Typ.
(864mm)
19-1/4"
(489mm)
66-3/16"
(1681mm)
30"
(762mm)
3
2"
(813
mm)
TUB W
IDTH
DRAIN END OF TUB
LEVELING
STRINGERS
ALLOW OPEN FRAME ON PUMP/MOTOR
OF WHIRLPOOL FOR PUMP CLEARANCE
(LH SHOWN)
SUGGESTED WHIRLPOOL/BATH
INSTALLATION METHOD
Leveling Stringer
1" x 3" (25 x 76mm) WOOD
Finished Wall
Waterproof Dry Wall
or Cement Board
Sealant
Tu b
Stud
(Wood or Steel)
SECURE THE BATH TO
THE STUDS AS SHOWN
FOR WOOD OR STEEL
STUD CONSTRUCTION.
FIG. 4
LEVELING
STRINGERS
NOTCH FOR
AIR CONTROL
(1/2" DEEP)
42-1/2"
(
1080mm
)
3-1/2"
(
89mm
)
ELECTRICAL DIAGRAM
READ AND FOLLOW ALL INSTRUCTIONS
BLACK
WHITE
120 VAC
GND.
SEPARATE
15 GFCI
OUTLET
WHIRLPOOL MOUNTED
AIR SWITCH OR
WALL TIMER
ELECTRICAL INSTALLATION
PUMP/MOTOR
753449-100 Rev. C
ELECTRICAL INSTALLATION INSTRUCTIONS
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes.
WARNING:
When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK
Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Install to permit access for servicing.
4. All building materials and wiring should be routed away from the pump body.
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the electrical power
supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded neutral wire and a third wire,
earth ground, are essential.
(3)
WIRE SELECTION GUIDE
Maximum distance from
fusebox to motor
The sizes shown on this
chart are recommendations
for copper conductors
only. Always follow
local and national
electrical codes
Motor
Hi-Performance
Rating
50' 100'
120V Power Line
150' 200'
12 12 10 8
1. 1
(4)
SPIC AND SPAN
®
IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE
753449-100 Rev. C
DRAIN CONNECTION AND SYSTEM TEST
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the pump couplings and
make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of the highest jet. Recheck the pump
couplings and make certain that they are not leaking. (Although the pump couplings are factory tightened and inspected, some loosening
may have occurred during transit.) Make sure the whirlpool is connected to the electrical supply and turn the whirlpool on. Check for
leaks around all piping connections while the whirlpool is running.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire
brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be
removed using granular Spic and Span
®
mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
FEATURES of YOUR NEW AMERICAN STANDARD ACRYLIC BATHTUB
Your new acrylic bathtub has been molded in the newest plumbing fixture material available today. Acrylics are tough
durable finishes that are simple and easy to care for.
The colors have been formulated to match other American-Standard fixtures and enhance your choice of bathroom
decorations. The high gloss surface is resistant to impact and chemicals and will retain its lasting luster with proper care
and maintenance.
AFTERCARE and CLEANING
• Always fill the tub with temperate water. Excessively hot water may cause surface damage
• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.
• Clean after use with a mild liquid household detergent cleaner. Do not use Lestoil, Lysol Disinfectant (spray or
concentrate), or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner, or cleaning
products in aerosol cans.
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.
• Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits, or other surface
blemishes.
• Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses
its sheen, dulled areas can be restored by rubbing with a white "automotive type" polishing compound and
waxing with a "liquid wax."
• Do not wax areas where you walk or stand.
• Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into
contact with the surface.
• Clean the surrounding surface immediately after using caustic drain cleaners.
• Burning cigarettes will damage the surface.
• Should damage to the fixture occur, repairs can be made quickly and easily.
Your distributor or builder can provide details.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

American Standard 1748102.222 Installation guide

American Standard
Brand
American Standard
Model
1748102.222
Category
Water pumps
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents