Black & Decker GT 250 Owner's manual

Page is loading ...

2

Hedgetrimmer

GT249/250/251/259/260/261

Introduction

This manual provides operating and maintenance

instructions for all of the hedgetrimmers in the

Black & Decker GT250/260 range including the

GT249/259.

Description (Fig. A)

A

1. Front handle switch

2. Front handle

3. Rear switch

4. Handle guard (GT251C & GT261C)

5. Front guard (GT249C, GT250C,

GT259C & GT260C)

6. Blade

7. Blade sheath

Know your machine

!

Warning! When using electric tools, basic

safety precautions should always be taken to

reduce the risk of fire, electric shock and

personal injury.

Read this manual carefully, observing

all of the recommended safety instructions

before, during and after using your

machine. Maintain your machine in good

working order.

Familiarise yourself with the controls on your

machine before attempting to operate it,

but above all, be sure you know how to stop

the machine in an emergency.

Retain this manual and all other literature

supplied for future reference.

Safety instructions

Preparation

• Dress properly. Do not wear loose

clothing or jewellery which could get

caught in moving parts. Always wear

stout, non-skid footwear and gloves

when operating your machine and

make sure that long hair is kept away

from the blades.

• Protect your eyes/ears. Use safety

glasses or goggles while operating your

Instruction Manual

machine. If the sound level seems

uncomfortable, use ear protection.

• Use outdoor extension cords. Never

use an indoor extension cable for use

with this machine.

• Do not abuse the cord. Never carry the

hedgetrimmer by its cord or yank the

cord to disconnect it from the socket.

Keep the cord away from heat, oil and

sharp edges.

• Remove the plug from the mains

immediately if the cable is damaged

or cut.

• Inspect hedge. Ensure that the hedge

has nothing lying on top of it or beside it,

e.g. barbed wire or railings which may

damage your machine.

• Consider the work environment.

Do not use the machine in the rain or

allow it to get wet or damp. Keep the

work area well lit. Do not use in the

presence of flammable liquids or gases.

Operation

• Avoid unintentional starting. Do not

carry a plugged-in tool with a finger on

the switch.

• Before using the machine. Disconnect

it from the electrical supply and visually

check that the blade fixings are secure.

A damaged blade or loose blade nuts are

a major hazard and must be replaced.

Always be sure that your machine is in a

safe operating condition.

• Guard against electric shock.

Avoid touching grounded surfaces

(e.g. railings, lamp posts etc.) while using

your machine.

360˚

6m/20ft

• Keep people away while the machine

is in use. Do not allow children, other

people or animals near your machine

while you are using it - always keep them

at least 6m (20ft) away from the cutting

area and never let anyone touch the

machine or the extension cord.

• Do not force the tool. It will do the job

better and more safely at the rate for

which it was intended.

3

ENGLISH

• Use the right tool. Never force small

tools or attachments to do the job of a

heavy duty tool. Do not use tools for

purposes not intended: e.g, do not use

the hedgetrimmer as a chain saw.

• Do not overreach. Keep proper footing

and balance at all times, especially while

working on a slope.

• Stay alert. Watch what you are doing.

Use common sense. Do not operate

when you are tired.

!

• Use the correct electrical supply.

Your machine is designed for use on

AC (mains) electrical supplies only - do

not attempt to use on any other supply.

Be sure to plug the machine into a power

point, never a lighting socket.

• Always turn off and unplug the

machine. Whenever you leave the

machine unattended. Before checking,

cleaning, adjusting, unjamming

the blades or carrying out work on

the machine. If the machine starts to

vibrate abnormally, check immediately.

After striking a foreign object- inspect for

damage and make repairs as necessary.

• Always keep the power supply cable

away from the blades. Be aware of its

position at all times.

• Do not put your hands or feet near the

blades and never attempt to stop the

blades - they will stop on their own.

• Never operate your machine with a

broken or missing guard.

• Remember that the operator/user is

responsible for accidents or hazards

occurring to other people or their

property. A first time user should get

some practical instruction on how to

use a hedgetrimmer as well as reading

this manual.

Maintenance and storage

• Always disconnect the machine

before carrying out any adjustment,

servicing or maintenance.

• Always lubricate the blades with

light machine oil after use to prevent

corrosion damage.

• Maintain tools with care. Always keep

tools sharp and clean for better and safer

performance. Follow instructions for

lubricating and changing accessories.

Inspect tool cords periodically and if

damaged have repaired by an authorised

service facility. Inspect extension cords

periodically and replace if damaged.

Keep handles dry, clean and free from oil

and grease.

• Check damaged parts. Before further use

of the tool, a guard or other part that is

damaged should be carefully checked to

determine whether it will operate properly

and perform its intended function. Check

for alignment of moving parts, binding of

moving parts, breakage of parts, mounting

and any other conditions that may affect its

operation. A guard or other part that is

damaged should be properly repaired or

replaced by an authorised service centre

unless otherwise indicated in this

instruction manual. Have defective

switches replaced by an authorised service

centre. Do not use the tool if the switch

does not turn it on and off.

!

Warning! The use of any accessory or

attachment, other than recommended in this

instruction manual, may present a risk of

personal injury.

Double insulation

Your machine is double insulated. This

means that all external metal parts are

electrically isolated from the power supply.

This is achieved by placing an extra

insulation barrier between the electrical and

mechanical parts. Double insulation means

greater electrical safety and obviates the

necessity of having the machine earthed.

Electrical safety

Your machine should always be switched off

at the mains before disconnecting any plug

and socket connector or extension cables.

Fuse replacement

If your machine is supplied with cable fitted

with a non-re-wireable plug.

• The plug is fitted with a 3 amp fuse

which is the recommended fuse for

your machine.

• Only use replacement fuses which are

approved to BS1362.

• When changing the fuse in your plug,

always ensure the fuse cover is refitted.

If the fuse cover is missing or damaged

do not use the plug.

Note: Fuses do not give personal protection

against electric shock.

4

Plug replacement

• Disconnect the plug from the supply.

• Cut off the plug and dispose of

immediately. Insertion of a detatched

plug into a 13 amp socket outlet may

result in electric shock.

• Only fit BS1363A approved plugs fitted

with the correctly rated fuse.

Fit a

BS1363A

approved

plug

Connect blue

to N (neutral)

Make sure that the

outer sheath of the

cable is held firmly

by the clamp

Fit a 3 amp

fuse approved

to BS1362

Connect brown

to L (live)

240 volts AC only.

Never use a light

socket

• The cable wire colours, or a letter, will be

marked at the connection points of most

good quality plugs. Attach the wires to

their respective points in the plug

(see above). Brown is for “Live” (L) and

blue is for “Neutral” (N).

• Before replacing the top cover of the

mains plug ensure that the cable restraint

is holding the outer sheath on the cable

firmly and that the two leads are correctly

fixed at the terminal screws.

!

Warning! Never connect live or neutral wires

to the earth pin marked “E” or .

Note: Do not wire an extension cable

directly into your machine yourself.

Instead, take your machine to your

nearest Black & Decker service centre.

Increased safety can be obtained by having

a qualified electrician install a high sensitivity

(30mA 30mS) circuit breaker in the house

wiring. If you do not wish to have one

installed, then we strongly recommend that

the electrical power to the machine be

supplied through a high sensitivity residual

current device (RCD). The RCD is designed

to provide a high degree of personal

protection against harmful electric current

should fault conditions occur.

!

Warning! The use of an RCD or other circuit

breaker unit does not release the operator of

the machine from the safety instructions and

safe working practices given in this manual.

We recommend that if your mains cable

is cut or requires replacement that you

return your machine to a Black & Decker

service centre. When repaired, your

machine will be tested for electrical safety.

Cable connection system

Black & Decker continually make every effort to

achieve the highest standards in performance, quality

and reliability and recommend the use of a new

outdoor cable connection system.

The new system gives additional protection against

the possibility of water or moisture entering into the

cable connector during normal use.

Note: The new connection system does not release

the operator of the machine from the safety

precautions and safe working practices given in the

instruction leaflet. Particular attention is drawn to the

coupler system as being ‘weather resistant’ and not

suitable for immersion, submersion or being

subjected to water jets. Care should be taken to

prevent the cable from lying or trailing through pools

of water or from splashing with hose pipes.

A6615 20m cable, socket, 13 amp plug

A6616 20m cable, socket, 13 amp plug and

cable tidy frame

A6617 30m cable, socket, 13 amp plug and

cable tidy frame

A6613 40m cable, socket, 13 amp plug and

cable tidy reel

Existing cable systems

Your hedge trimmer comes with either, 12 metre

cable attached (Cat. number ends with a C), or a

male connector built into the product. If you already

own an outdoor cable system, we recommend that

you replace the existing ‘female’ cable connector with

the new ‘female’ connector which is available

as an accessory from most major DIY retail outlets

and from Black & Decker service centres

(cat. no. A6624S).

old ‘female’ connector new ‘female’ connector

When fitting the connector, follow the instructions

which are supplied with it. If in doubt, consult a

qualified electrician.

Existing powered garden tools

To connect existing Black & Decker garden power

tools to the new system you will require an adaptor

(see below). This is available as an accessory from

most major DIY retail outlets (cat. no. A6623S).

5

ENGLISH

!

Warning! This adaptor is only suitable for

products rated up to 500W. It is not

recommended for use with the following:

Hover mowers, rotary mowers with grass

collection, chainsaws, shredders and blower

vacs. Please contact your local service

centre should you require further advice.

Fitting your own extension cable

• When making your own extension cable, fit a

13 amp plug (see “fitting the mains plug”) to one

end of the cable and a ‘female’ connector to the

other end (see below). For wiring instructions see

those supplied with the female connector.

• A ‘male’ connector is already attached to the

electrical supply cable on your machine and is

designed to be non-rewireable (see below).

This should not be removed. Should the plug

become damaged or need replacing, please

return the machine to your Black & Decker

service centre.

‘female’ connector ‘male’ connector

!

Warning! Never wire an extension cable with

anything other than the ‘female’ connector

supplied and a 13 amp BS1363A approved

plug with the recommended fuse. Never

wire a ‘male’ connector to your extension

cable and never wire an extension cable

with a plug of any kind at each end of the

cable. This is extremely dangerous and

results in the pins being live which may

cause a fatal electric shock.

Technical data

Specifications

Insulation Class II

Strokes per minute 1900

Blade length 41cm, 51cm

Weight 2.4 to 2.5kg

Noise 88dB (A)

Vibration <2.5m/s

2

Assembly (Figs. B & C)

B

• You will need a number 2 Posidrive

screwdriver.

• During assembly it is recommended that

the blade sheath is fitted over the blades

to reduce the risk of injury.

Fitting the guard

C

• Slide the guard into position as shown.

• Fix in place using two of the screws

provided. Do not over tighten them.

Operation (Fig. D)

To start the hedgetrimmer

• Press the front handle switch (Fig. A.1).

• Squeeze the rear switch (Fig. A.3).

• The hedgetrimmer will now run.

To stop the hedgetrimmer

• Release the front handle switch or the

rear switch.

D

This product is built with a cable retention

system. To operate this, feed your cable

through the hole provided and hook it over

the pegs as shown in Fig. D.

Useful hints for trimming hedges

(Fig. E)

Read the safety rules first!

Cutting

E

• Tip the blades a little towards

the hedge (Fig. E1).

• First cut both sides, working from the

bottom up, then trim the top (Fig. E2).

• Take care to avoid any hard objects in or

around the hedge that could damage

the blades.

• Where the branches are very long,

cut the hedge back in several stages

(short cuttings are easier to tidy up).

When to trim

• As a general guide, hedges and shrubs

with seasonal leaves (new ones each year)

can be trimmed in June and October.

• Evergreens can be trimmed in April

and August.

6

• Conifers and other fast growing shrubs

can be trimmed about every six weeks

from May onwards.

Failure to work

If your hedgetrimmer does not work, unplug it

and check:

• The power point (try another tool or appliance).

• The plug and its fuse.

• The plug and socket connections.

If in doubt, get help from a qualified electrician, or visit

your Black & Decker service centre.

Care and maintenance

• Switch off and disconnect from power supply

before cleaning or adjusting your machine.

• For best performance, keep the blades and air

slots in the motor housing clean. Use a cloth or

brush to remove cuttings, sap or other debris.

• Prevent the blades from rusting by applying a film

of light machine oil after cleaning.

• Plastic parts may be cleaned by using a non

abrasive cleaner and a cloth dampened with

warm water.

• Do not immerse any part of the hedgetrimmer

in water.

• Avoid all other types of detergents, cleaners or

solvents. These may contain chemicals that

could seriously damage the plastic. Do not spray

the hedgetrimmer with water, and do not allow

water to enter the hedgetrimmer.

• After cleaning, the tool can be stored in its

packaging for protection.

• Self lubricating bearings are used in the tool and

lubrication is not required. (Other than to the

blades as stated above).

What to do if your hedgetrimmer

needs repair

Information on how and where to send your

hedgetrimmer for repair or service is given at the

back of this leaflet. We recommend you keep this

in a safe place.

Unwanted products and

the environment

Should you find one day that your product

needs replacement, or is of no further

use to you, think of the protection of the

environment. Black & Decker service centres

will accept your old products and will dispose

of them in an environmentally safe way.

Black & Decker lawn and

garden guarantee

This guarantee provides 36 months parts cover

and 12 months labour. In all cases proof of

purchase will be required.

If your Black & Decker product becomes defective,

within the guarantee period, due to faulty materials

and workmanship, we guarantee to either replace all

defective parts, or at our discretion, replace the unit

free of charge, provided that:

• The product is returned to us or our authorised

repairers with evidence of purchase.

• The product has been used within the

parameters of its consumer classification.

• The product has not been used for hire

purposes.

• Repairs have not been attempted by anyone

other than our own service staff or authorised

repairers.

• The failure represents normal wear and tear.

This guarantee is offered as an extra benefit and is

additional to your statutory rights.

The guarantee policy

Failures due to the following are not covered:

• Replacing worn or damaged blades, nylon line

and chains, or cords damaged during storage or

use. These are regarded as replacement items

which wear during normal usage.

• Failures as a result of sudden impact or

obvious abuse.

• Failures due to usage not in accordance with

instructions and recommendations contained in

the instruction manual.

The use of other than genuine Black & Decker

accessories and parts may damage or reduce the

performance of you Black & Decker product and

may render the guarantee void.

Black & Decker after sales service

Black & Decker offers a nationwide after sales service

through company operated service centres. It is our

aim to offer excellent service, fast repairs, extensive

parts availability and full accessory support.

If you need any help or advice please contact your

local Black & Decker service centre manager.

Full details of our unique after sales service can be

obtained from any of our service centres (a full

directory is printed on the reverse of the parts

drawing included with your product).

7

ENGLISH

Other Black & Decker products

Black & Decker has a full range of outdoor power

tools that make life easy in the garden. If you would

like further information on other products, please

contact the Black & Decker service information

centre at the address on the back cover, or contact

your Black & Decker stockist.

Other products include (UK only):

Lawn mowers Hedge trimmers

Grass trimmers Chainsaws

Lawnrakers Compost shredders

Blower vacs

EC Declaration of Conformity

We declare that units:

GT249, GT250, GT251, GT259, GT260, GT261

conform to: 89/392/EEC, 89/336/EEC,

EN50144, EN55014, EN55104, 73/23/EEC

A weighted sound pressure 91dB (A)

A weighted sound power 104dB (A)

Hand/arm weighted vibration <2.5m/s

2

Brian Cooke

Director of Engineering

Spennymoor, County Durham DL16 6JG

United Kingdom

Page is loading ...

25

PORTUGUÊS

EC Declaração de Conformidade

Declaramos que os produtos:

GT259, GT250, GT251, GT259, GT260, GT261

estão de acordo com 89/392/EEC, 89/336/EEC,

EN50144, EN55014, EN55104, 72/23/EEC

Pressão sonora 91dB (A)

Potência sonora 104dB (A)

Vibração <2.5m/s

2

Brian Cooke

Engenheiro Responsável

Spennymoor, County Durham DL16 6JG

United Kingdom

Page is loading ...

44

• GARANTI KORT • GARANTIEKARTE •

KAPTA E°° YHΣHΣ

• GUARANTEE CARD • TARJETA DE GARANTÍA • CARTE DE GARANTIE

• TAGLIANDO DI GARANZIA • GARANTIE-KAART • GARANTI KORT • CARTÃO DE GARANTIA • TAKUUKORTTI • GARANTIBEVIS

Australia Call 1900 937766 (max. call charge $2.00 ex. tax) Nederland Florijnstraat 10, 4879 AH Etten-Leur

Belgique/België Weihoek 1, 1930 Zaventem New Zealand Call 0900 97766 (max. call charge $2.00 ex. tax)

Danmark Hejrevang 26B, 3450 Allerød Norge Strømsveien 344, 1081 Oslo

Deutschland Black & Decker Str. 40, D-65510 Idstein Österreich Erlaaer Straße 165, 1231 Wien

Eλλάς Black & Decker Eλλάς, Συγγρïύ 154, 17671 Kαλλιθέα

Portugal Rua Egas, Moniz 173, S. João do Estoril, 2768 Estoril Codex

España 43883 Roda de Barà (Tarragona) South Africa After sales service, PO Box 5303, Johannesburg 2000

France BP21, 69571 Dardilly Cedex Suomi Black & Decker Oy, Rälssitie 7C, 01510 Vantaa

Helvetia Rütistraße 14, 8952 Schlieren, Schweiz/Suisse Sverige Box 603, 421 26 Västra Frölunda

Italia Viale Elvezia 2, 20052 Monza (MI) UK & Ireland PO Box 821, Slough, Berkshire, SL1 3AR

Danmark Venligst klip denne del ud og send frankeret til Black & Decker

i dit land.

Deutsch Bitte schneiden Sie diesen Abschnitt ab, stecken ihn in einen

frankierten Umschlag und schicken ihn direkt an die

Black & Decker Adresse Ihres Landes.

Eλληνικα

Παραρακαλώ κÞψτε αυτÞ τï κïµµάτι και ταøύδρïµήστε τï

αµέσως µετά την αγïρά τïυ ρïιÞντïς σας στην διεύθυνση

της Black & Decker στην ελλάδα (âλέ ε άνω).

English Please cut out this section, put into a stamped addressed

envelope and post immediately after the purchase of your

product to the Black & Decker address in your country (above).

If you live in Australia or New Zealand, please register by phone.

Español Después de haber comprado su herramienta envie usted, por

favor, esta tarjeta a la central de Black & Decker en su país.

Français Découpez cette partie et envoyez-la sous enveloppe timbrée à

l’adresse de Black & Decker dans votre pays (voir ci-dessus),

ceci immédiatement après votre achat.

Italiano Per favore ritagliate questa parte, inseritela in una busta con

francobollo e speditela subito dopo l’acquisto del prodotto

all’indirizzo della Black & Decker nella vostra nazione (vedi sopra).

Nederlands Knip dit gedeelte uit, zend het in een gefrankeerde,

geadresseerde envelop direct na uw aankoop naar het

Black & Decker-adres in uw land (zie boven).

Norge Vennligst klipp ut denne delen umiddelbart etter du har pakket

ut ditt produkt og legg det i en adressert konvolutt til

Black & Decker (Norge) A/S (se adresse over).

Português Por favor, recorte esta parte, coloque-a num envelope selado

e enderessado e envie-0 logo após a compra do seu produto

para o enderesso da Black & Decker do seu país.

Suomi Leikkaa irti tämä osa, laita se oheiseen kuoreen ja postita

kuori yllä olevaan paikalliseen Black & Decker osoitteeseen.

Sverige Var vänlig klipp ur denna del. Skriv Ditt namn och adress på

ett frankerat kuvert, och sind det genast till Black & Deckers

adress i DItt land (se ovan).

Part no. 369162-01 10/96

Page is loading ...

Black & Decker GT 250 Owner's manual

Black & Decker GT 250 Owner's manual

in other languages

Related papers

Other documents