SPECIFKATIONS
PROVUC(X) -
COLOR l/3” CCD CAMERA
TYPE
COLOR l/3” CCD CAMERA
Image Pick-up Device
Interline transfer
Picture Elements
5 IO( (V) NTSC ,500 (H)x582(V) PAL
Resolution
330 Horizontal TV Lines
Minimum Illumination
1.5 Lux/F 1.2
Scanning System
IInterlace 2: 1
Auto Electronic
INTSC: l/60 to I/lOO.OOO sec. linear switchable
Shutter
Auto Iris Control
Lens Mount
S/N Ratio
Gain Control
1 Automatic
White Balance
/Automatic
’ PAL : t/SO to l/100,000 sec. linear switchable
Video Driver / 4 Pins Connector
CS or C mount
More than 46 dB
LWeight
1580 g
I
AC Adaptor (Sold separateIy). Javelin model #PS 1824
Javelin Systems maintains a complete technical staff to assist in
specifying and using Javelin products. Javelin is an Equal Opponunity
Employer. Javelin reserves the right to change features and
specifications without notice. Printed in the USA.
JAVELIN
INSTRUCTION MANUAL ’
‘I
This color camera uses high sensitive l/3” interline transfer CCD imag
sensor (CCD = Charge Coupled Device), and all state circuitry which
provides extremely long life and high reliability. This camera offers
excellent image quality with low lag and high bum resistance. and is
not subject to distortion from magnetic fields .
High resistance to shock and vibration , easy to install , this camera is
very good choice for your color CCTV system.
CONTENTS
Description . . . . . . . . . . . . . . . . . . . . .
Page I
Main features. . . . . . . . . . . . . . . . . .
Page 2
Cautions on handling . . . . . . .
Page 2
Cautions on installation... Page 2
Name of each part . . . . . . . . . . .
Page 3
How to operate . . . . . . . . . . . . Page
Packing .__..................... Pagl
Auto Iris Control . . . . . . . . Pagt
Specifications . . . . . . . . . . . . . . . Pag,
JAVELIN SYSTEMS
23456 HAVVTHORNE BLVD BLDG 5
TORRANCE CA 905054716
Page6
MMN FEATURES
Resolution
Number of Pixels
Light
Auto EIectronic Shutter
Cain Control/White Balance
Mount
330 Lines
N-J’SC = 250.000 / PAL = 291,000
1.5 Lux F 1.2
l/50(1/60) to l/100.000 sec.
Automatic control
C & CS mount
CAUTIONS ON HANDLING
(1) Be careful , never let any water in this equipment..
(2) Do not directly .touch the CCD element.
If necessary , use a
soft cloth moistened with alcohol to wipe off the dust.
(3) When any abnormalities occur, make sure to unplug the unit
and contact your local dealer.
CAUTIONS ON INSTALLATION
( 1) Be extra careful not to shake the camera.
(2) Avoid places where there is direct sunlight.
(3) When using this camera in places where the lighting differs
greatly, please use the auto iris lens with ND filter.
(4) Avoid places where temperatures exceed 50°C or more t
high humidity or where direct rain drops hit.
(5) Avoid places where there is frequent vibrations or shocks.
(6) Ifduring the night, the minimum brightness of 0.5 Lux cannot
be achieved , install appropriate light fixtures.
(7) When the camera is not used , keep the lens or the lens cap
attached to protect the CCD sensor.
(8) Use individual power supply for proper operation . Javelin
model #PS 1824 or equal. Connect power cable to camera
prior to power source.
VfDEO DRIVE TYPE LENSES
t
AUTO IfuS CONTROL CONNECTOR ,
1 VDC
2 lRrSOUT
3
GND
4 GND
JAVELIN SYSTEMS
A Division of Ademco Security Group, Inc.
4
USA
325 Maple Avenue, Tomance , CA 90503-2602
TEL :(310) 618-2140 or (800) 421-2716
FAX: (3 10) 787-8374
EUROPE
8 Pippin Ln Little Billing, Northampton NN3 9UA , England
TELiFAX:+44.( 1) 604406887
Page2
Page5
NAME OF EACH PART
HOW ‘I-0 OYERA’I-E
UCS yount Lens + Cap
a . ,p Mounting 8racket
I3
2
CS Mount Fting Screw
h Mounting Bracket
A$o
Iris
4
Pins Caonecfor
+r IN
Design and specifications are subject to change without
prior notice.
,
(I )Remove the cap cover from the top of the lens mount.
(2) If CS mount lens is used , also remove the C mount ring.
(3) Screw the lens into the lens mount Rep: I.
(4) Connect the video output Rep:4 to the monitor or other video
device through a 75 Ohms type coaxial cable.
(5) Connect the power Rep:7 source. AC with the power cord.
(6) Once the picture appears on the monitor, adjust the focus and
iris of the lens to obtain the best picture.
(7) If the subject is not in correct focus when adjusting focus of
the lens, do back focus, adjust as follows:
1:
Set the focus ring of the lens to indefinite position.
II- Take picture of subject at a distance more than 20 m away
III- Loosen the mount lens fixing screw Rep:2 (use L wrench).
IV- Turn the lens and the mount lens together so the subject
is in the focus and the picture is clear.
V- Screw the mount lens fixing screw.
(8) When using an auto iris lens , connect the enclosed miniature
4 pins plug following the diagram and plug the connector
into the socket Rep:6. When using an auto iris lens, the switch
Rep:5 should be in OFF position. When using a manual lens ,
this switch should be in ON position.
(9) Mount the camera on the mounting bracket with a l/4-20 screw.
PACKING
1 Camera
1 L Wrench
1 Connector 4 pins for auto iris lens
1 Javelin instruction manual
Page3 Page4
NAME OF EACH PART
HOW ‘I-0 OYERA’I-E
UCS yount Lens + Cap
a . ,p Mounting 8racket
I3
2
CS Mount Fting Screw
h Mounting Bracket
A$o
Iris
4
Pins Caonecfor
+r IN
Design and specifications are subject to change without
prior notice.
,
(I )Remove the cap cover from the top of the lens mount.
(2) If CS mount lens is used , also remove the C mount ring.
(3) Screw the lens into the lens mount Rep: I.
(4) Connect the video output Rep:4 to the monitor or other video
device through a 75 Ohms type coaxial cable.
(5) Connect the power Rep:7 source. AC with the power cord.
(6) Once the picture appears on the monitor, adjust the focus and
iris of the lens to obtain the best picture.
(7) If the subject is not in correct focus when adjusting focus of
the lens, do back focus, adjust as follows:
1:
Set the focus ring of the lens to indefinite position.
II- Take picture of subject at a distance more than 20 m away
III- Loosen the mount lens fixing screw Rep:2 (use L wrench).
IV- Turn the lens and the mount lens together so the subject
is in the focus and the picture is clear.
V- Screw the mount lens fixing screw.
(8) When using an auto iris lens , connect the enclosed miniature
4 pins plug following the diagram and plug the connector
into the socket Rep:6. When using an auto iris lens, the switch
Rep:5 should be in OFF position. When using a manual lens ,
this switch should be in ON position.
(9) Mount the camera on the mounting bracket with a l/4-20 screw.
PACKING
1 Camera
1 L Wrench
1 Connector 4 pins for auto iris lens
1 Javelin instruction manual
Page3 Page4
MMN FEATURES
Resolution
Number of Pixels
Light
Auto EIectronic Shutter
Cain Control/White Balance
Mount
330 Lines
N-J’SC = 250.000 / PAL = 291,000
1.5 Lux F 1.2
l/50(1/60) to l/100.000 sec.
Automatic control
C & CS mount
CAUTIONS ON HANDLING
(1) Be careful , never let any water in this equipment..
(2) Do not directly .touch the CCD element.
If necessary , use a
soft cloth moistened with alcohol to wipe off the dust.
(3) When any abnormalities occur, make sure to unplug the unit
and contact your local dealer.
CAUTIONS ON INSTALLATION
( 1) Be extra careful not to shake the camera.
(2) Avoid places where there is direct sunlight.
(3) When using this camera in places where the lighting differs
greatly, please use the auto iris lens with ND filter.
(4) Avoid places where temperatures exceed 50°C or more t
high humidity or where direct rain drops hit.
(5) Avoid places where there is frequent vibrations or shocks.
(6) Ifduring the night, the minimum brightness of 0.5 Lux cannot
be achieved , install appropriate light fixtures.
(7) When the camera is not used , keep the lens or the lens cap
attached to protect the CCD sensor.
(8) Use individual power supply for proper operation . Javelin
model #PS 1824 or equal. Connect power cable to camera
prior to power source.
VfDEO DRIVE TYPE LENSES
t
AUTO IfuS CONTROL CONNECTOR ,
1 VDC
2 lRrSOUT
3
GND
4 GND
JAVELIN SYSTEMS
A Division of Ademco Security Group, Inc.
4
USA
325 Maple Avenue, Tomance , CA 90503-2602
TEL :(310) 618-2140 or (800) 421-2716
FAX: (3 10) 787-8374
EUROPE
8 Pippin Ln Little Billing, Northampton NN3 9UA , England
TELiFAX:+44.( 1) 604406887
Page2
Page5
SPECIFKATIONS
PROVUC(X) -
COLOR l/3” CCD CAMERA
TYPE
COLOR l/3” CCD CAMERA
Image Pick-up Device
Interline transfer
Picture Elements
5 IO( (V) NTSC ,500 (H)x582(V) PAL
Resolution
330 Horizontal TV Lines
Minimum Illumination
1.5 Lux/F 1.2
Scanning System
IInterlace 2: 1
Auto Electronic
INTSC: l/60 to I/lOO.OOO sec. linear switchable
Shutter
Auto Iris Control
Lens Mount
S/N Ratio
Gain Control
1 Automatic
White Balance
/Automatic
’ PAL : t/SO to l/100,000 sec. linear switchable
Video Driver / 4 Pins Connector
CS or C mount
More than 46 dB
LWeight
1580 g
I
AC Adaptor (Sold separateIy). Javelin model #PS 1824
Javelin Systems maintains a complete technical staff to assist in
specifying and using Javelin products. Javelin is an Equal Opponunity
Employer. Javelin reserves the right to change features and
specifications without notice. Printed in the USA.
JAVELIN
INSTRUCTION MANUAL ’
‘I
This color camera uses high sensitive l/3” interline transfer CCD imag
sensor (CCD = Charge Coupled Device), and all state circuitry which
provides extremely long life and high reliability. This camera offers
excellent image quality with low lag and high bum resistance. and is
not subject to distortion from magnetic fields .
High resistance to shock and vibration , easy to install , this camera is
very good choice for your color CCTV system.
CONTENTS
Description . . . . . . . . . . . . . . . . . . . . .
Page I
Main features. . . . . . . . . . . . . . . . . .
Page 2
Cautions on handling . . . . . . .
Page 2
Cautions on installation... Page 2
Name of each part . . . . . . . . . . .
Page 3
How to operate . . . . . . . . . . . . Page
Packing .__..................... Pagl
Auto Iris Control . . . . . . . . Pagt
Specifications . . . . . . . . . . . . . . . Pag,
JAVELIN SYSTEMS
23456 HAVVTHORNE BLVD BLDG 5
TORRANCE CA 905054716
Page6
AUTO IRIS CONTROL CONNECTOR
VIDEO DRIVER
t12 (Kc)
1
IRK (VIDEO OUT) 2
X (NOT USED)
3
GND
4
DC
DRIVER
(DIRECT
DRIVE)
1 DAMP-
2 DAMP+
3 DRIVE+
4 DRIVE-
SPECIFICATIONS
Same characteristics of the standard camera:
image pick-up device, picture elements, resolution, scanning
system, auto electronic shutter, lens mount S/N ratio, gamma,
synchro system, video output.
VARIABLES
. . ,
- ---
Consumption
11 OmA at 24vac
Weight
525~1
l/3” CCD CAMERA FUNCTION @
Video Output
Switch AVAES
BLC ON/OFF
(color only)
ON 9
9 Auto his 4 Pins Con.
LED Camera
Power IN @
24 VAC Terminal Block
I
.,
(8) When using an Auto Iris Lens, before plugging in the enclosed
miniature 4 pins connector, please check the type of Auto Iris Lens,
and also the compatibility on the polarities. The Switch @should
be in position OFF. If the Auto Iris Lens is DC DRIVE or DIRECT
DRIVE, the Switch @should be in position DC DRIVE. Adjust the
level with the VR @. If the Auto Iris Lens is VIDEO DRIVE, the
Switch dD should be in position VIDEO DR. When using a Manual
Iris Lens, the Switch.6) should be in position ON, and the Switch dD
should be in “NO USE” position.
AUTO IRIS CONTROL CONNECTOR
VIDEO DRIVER
t12 (Kc)
1
IRK (VIDEO OUT) 2
X (NOT USED)
3
GND
4
DC
DRIVER
(DIRECT
DRIVE)
1 DAMP-
2 DAMP+
3 DRIVE+
4 DRIVE-
SPECIFICATIONS
Same characteristics of the standard camera:
image pick-up device, picture elements, resolution, scanning
system, auto electronic shutter, lens mount S/N ratio, gamma,
synchro system, video output.
VARIABLES
. . ,
- ---
Consumption
11 OmA at 24vac
Weight
525~1
l/3” CCD CAMERA FUNCTION @
Video Output
Switch AVAES
BLC ON/OFF
(color only)
ON 9
9 Auto his 4 Pins Con.
LED Camera
Power IN @
24 VAC Terminal Block
I
.,
(8) When using an Auto Iris Lens, before plugging in the enclosed
miniature 4 pins connector, please check the type of Auto Iris Lens,
and also the compatibility on the polarities. The Switch @should
be in position OFF. If the Auto Iris Lens is DC DRIVE or DIRECT
DRIVE, the Switch @should be in position DC DRIVE. Adjust the
level with the VR @. If the Auto Iris Lens is VIDEO DRIVE, the
Switch dD should be in position VIDEO DR. When using a Manual
Iris Lens, the Switch.6) should be in position ON, and the Switch dD
should be in “NO USE” position.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Javelin BWM17X User manual
-
Gill IMPLEMENT CERTIFICATION KITS Operating instructions
-
-
MyBinding Foster Keencut Javelin User manual
-
-
Therma-Tru Light Commercial/Multi-Family / 22 & 24 Gauge Steel Edged Door User manual
-
Kodak C 503 User manual
-
Kodak Slice User manual
-
Bosch VEZ-211-IWCS Datasheet
-
