Kathrein UFSCONNECT 906SW Owner's manual

Brand: Kathrein

Model: UFSCONNECT 906SW

Category: AV receivers

Type: Owner's manual

This manual is also suitable for

UFSconnect 906

Operating Instructions Part 1

Connection and set-up

UFSconnect 906

English

Vous trouverez la version

française du document sur

www.kathrein.com

IMPORTANT

Read carefully

before use!

2 of 64

1 Contents

1 Contents ...........................................................................................................2

2 Safety Instructions - Important Notes ...........................................................4

3 Product Package .............................................................................................8

4 Inserting batteries in the remote control ....................................................... 9

5 Views of the receiver .....................................................................................10

6 Connecting the receiver ................................................................................12

6.1 Connection of the unit to the TV set ........................................................................12

6.2 Audio connection .......................................................................................................13

6.2.1 Digital ...........................................................................................................................13

6.2.2 Analogue ......................................................................................................................13

7 First Installation .............................................................................................14

7.1 Buttonsrequiredforremotecontrolduringrstinstallation ................................14

7.2 Switch on the TV set and receiver ............................................................................14

7.3 Step 1: Language Selection ......................................................................................14

7.4 Step 2: TV, Video, and Audio .....................................................................................15

7.5 Step3:Tunerconguration.......................................................................................17

7.5.1 DiSEqC™1.0 ................................................................................................................19

7.5.2 DiSEqC™1.1 ................................................................................................................21

7.5.3 Motorized antenna: DiSEqC™1.2/DiSEqC™1.3 (USALS) ..........................................24

7.5.3.1 DiSEqC™1.2 ...............................................................................................................................25

7.5.3.2 DiSEqC™1.3 ...............................................................................................................................28

7.5.4 LNB only .......................................................................................................................31

7.5.5 OneCable system .........................................................................................................33

7.5.5.1 EXR .../EXU ... (Kathrein OneCable matrices) ............................................................................34

7.5.5.2 UAS 481 (Kathrein OneCable LNB) ............................................................................................37

7.5.5.3 User-dened ................................................................................................................................38

7.6 Step 4: Channel Search .............................................................................................41

7.7 Step 5: Time setting ...................................................................................................44

7.8 Step 6: Changes to the ASTRA channel list ............................................................45

3 of 64

8 Software update ............................................................................................ 46

9 Network/Internet connection ....................................................................... 47

9.1 DHCP "On" ................................................................................................................. 48

9.2 DHCP "Off" ................................................................................................................ 48

10 Common Interface (CI) ................................................................................. 49

10.1 Inserting the Smartcard and the CI+/CI module ..................................................... 49

11 UFSconnect ................................................................................................... 50

12 Accessories (not included in the product package) ................................. 52

13 Troubleshooting, service ............................................................................. 53

13.1 Troubleshooting ........................................................................................................ 53

13.2 Service ....................................................................................................................... 54

14 Advanced connection example ................................................................... 55

15 TechnicalSpecication ................................................................................ 56

16 Connection examples for satellite reception systems .............................. 57

16.1 Individual system ...................................................................................................... 57

16.2 Community antenna network systems ................................................................... 57

16.3 OneCable system ...................................................................................................... 58

17 Connection examples for network and UFSconnect ................................ 59

17.1 Direct connection receiver - PC/laptop ................................................................... 59

17.2 Integrating the receiver into a network ................................................................... 60

18 For your notes .............................................................................................. 62

Youcanndexplanationsofthereceiverfunctionsthatgobeyondtheconnection

andinitialsettingupandrstinstallationintheOperatingInstructionsPart2"Basic

Functions and Operation".

4 of 64

2 Safety Instructions - Important Notes

These two pages contain important information about the operation, installation location and

connection of the unit. Read these instructions carefully before setting up the unit.

Mains power cable

Ensure that the mains cable (power cable) is not damaged and does not become

damaged. Units with a damaged mains power cable must be separated from the

mains power supply (by pulling out the mains plug) and serviced by an approved

electrician before it is put back into use again. Only use the power pack supplied

(if available)! The use of any other power supply unit may damage the receiver.

Risk of fatal injury due to electric shock or burns!

Playing children

Make sure that children do not push any objects into the ventilation slots.

Risk of fatal injury due to electric shock!

Mains voltage

Only operate the unit at the specied mains voltage (indicated on the rear of the

unit or on the external power pack). The unit may only be connected to the mains

and turned on once it has been connected to the antenna and to the TV set or the

cable network and PC.

Ifthemainsvoltageistoohigh,thereisariskofre!

Warning!

The signal indicates a hazard with a medium degree

of risk which, if it is not avoided, can result in death

or severe injury.

Caution!

The signal indicates a hazard with a medium degree

of risk which, if it is not avoided, can result in slight

or moderate injury.

General warning sign

General prohibition sign

General sign giving orders

Useful note

Warning!

Explanation of the symbols and notes

Tip!

5 of 64

Ventilation of the unit

The heat generated in this unit is adequately dissipated. However, the unit should

never be installed in a cupboard or on shelves with inadequate ventilation.

Never cover the cooling slots on the unit (e.g. with other equipment, magazines,

tablecloths, clothing or curtains)! Otherwise the unit may overheat. Do not place

any objects on top of the unit. Unless stated to the contrary in the "Connection and

set-up" and "Installation" sections in the instructions supplied, maintain a clearance

of at least 10 cm above the unit, 2 cm to either side and 5 cm behind the unit, to

allow unobstructed dissipation of the heat generated.

Thereisariskofre!

Moisture,directsunlight,heat,nakedames

The power supply unit and the receiver are for indoor use only! Protect the unit

against moisture, dripping and splashed water (do not place any lled objects such

as vases on top of the unit). Do not place the unit close to a heater or expose it

to direct sunlight and do not operate it in damp locations. Only use the unit in a

moderate climate, not in tropical conditions! Do not place naked ames such as

candles on top of the unit!

Thereisariskofre!

Cleaning

Disconnect the mains plug before cleaning the unit. Use a dry cloth for cleaning.

Only clean the surface. Never open the casing of the unit.

Touching the parts inside the unit carries a risk of death due to electric shock!

Warning!

Repairs

Ensure that any repairs to your unit are carried out by qualied personnel. Opening

the unit and attempting to repair it yourself voids all warranty claims! Improper work

on the unit may jeopardise the electrical safety of the unit.

The manufacturer accepts no liability for accidents caused by the user opening the

unit casing!

Connections

Incorrect wiring of the connections may lead to malfunctions or defects on the unit!

Caution!

6 of 64

2 Safety Instructions - Important Notes

Periods of extended absence, thunderstorms, mains socket accessibility

In order to disconnect the unit from the mains completely, the mains plug must

be unplugged from the mains power socket! Set up the unit near a mains socket.

Ensure that this mains socket is accessible so that you are in a position to separate

the unit from the mains supply at any time.

Always turn off the unit at the mains switch if you will be absent for a long time or

there is a storm. Break the connection by pulling out the mains plug from the mains

socket. This also applies to the other equipment connected to the unit. Isolation

from the cable network is also recommended. Note any timer programming

(receiver) and turn the unit on again promptly before the recording time.

Installation location

All electronic equipment generates heat. The temperature rise of this unit does,

however, lie within the permissible range. Sensitive furniture surfaces and veneers

may become discoloured by the effects of constant heat over time. The feet of

the unit can also cause colour changes to treated furniture surfaces. If necessary,

place the unit on a suitable stable and at base.

Disposal

Electronic equipment is not domestic waste - in accordance with directive

2002/96/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL dated

January 2003 concerning used electrical and electronic appliances, it must be

disposed of properly. At the end of its service life, take this receiver for disposal at

a designated public collection point.

Earthing

The antenna system must be earthed as specied or equipotentially bonded.

EN 60728/11 and any national regulations must be complied with.

Risk of voltage surges due to lightning strikes!

Batteries

If your unit was supplied with batteries (e.g. for the remote control), take care that

the batteries are not exposed to excessively high temperatures, direct sunshine or

re. Replace the batteries only with types that are identical or equivalent, otherwise

the batteries or the remote control may be damaged. Also comply with the safety

instructions given on the batteries.

There is a risk of explosions!

Caution!

Tip!

7 of 64

Product return/original packaging

Please keep the original packaging in case you need to return the product at any

time. The receivers are fragile due to their construction and are only adequately

protected by the original packaging. If the receiver is not shipped correctly the

guarantee/warranty on it will be voided.

Switching the receiver off

Before you disconnect the receiver from the mains, you must switch it to the

standby mode by pressing the standby button (on/off) on the remote control. In

standby mode, any changed or new data that are broadcast will be saved by the

receiver. As soon as the receiver is in the standby mode, it can be disconnected

from the mains at any time.

Do not disconnect the receiver from the mains while it is in operation!

This can lead to a loss of data and corruption of the software.

Storage of the operating instructions

Keep these operating instructions for any questions that arise later, and if the

receiver passes to another owner, pass them on to the new owner.

Other

The information in these operating instructions was correct at the time of going to

print. However, we reserve the right to make changes at any time and without prior

notice. If new software is released for your receiver, and this affects the information

in the operating instructions (e.g. changes to the menus and/or functions), if we

believe it necessary we will make available new operating instructions for download

at "www.kathrein.de".

Make a note of the receiver's basic settings (these are set during rst installation),

so you can restore them if necessary.

Spent batteries are special waste

Do not throw used batteries into your household waste; take them to a collection

point for old batteries.

8 of 64

3 Product Package

► UFSconnect 906

► Remote control RC 678

► HDMI cable

► Power supply unit 230 V/12 V

► 2 batteries AAA 1.5 V

► Operating Instructions (Parts 1, 2 and 3)

► Safety instructions (multi-lingual)

Graphic: Product Package

HDMI cable

Remote control Power supply unit

Accessories

see below

Operating

instructions

Receiver

The accessories supplied may differ in appearance from those illustrated.

9 of 64

4 Inserting batteries in the remote control

Remove the cover on the rear of the remote control. Insert the two batteries supplied into the

remote control. Ensure that the polarity of the batteries is correct. This is marked on the bottom

of the battery compartment. Slide the cover back onto the housing until it locks in place.

To open:

Gently press here and

pull backwards

Graphic: Inserting the batteries

1 2 43

5 6 9

10 14 15 1611

12 13 17

10 of 64

5 Views of the receiver

Graphic: Front view Graphic: Rear view

11 of 64

1. On/Off button (operation/standby)

2. Channel selection (P-)

3. 16-character display

4. Channel selection (P+)

Front view: Rear view:

)

CI+/CI modules and Smartcards are not included in the product package

)

Infrared sensor (BN 20410017) is not included in the product package

***

)

Pressing the Off switch does not full disconnect the unit from the mains

(see the sections "Safety Instructions - Important Notes" and "Periods of

extended absence, thunderstorms, mains socket accessibility")

The serial number sticker for the UFSconnect 906 is located on the

underside of the unit. The information printed on it includes the

following:

► the exact designation (e.g. UFSconnect 906si)

► the part number and

► the serial number of the unit.

You do not need this information in order to operate the unit.

If however, contrary to expectations, you need to make a claim

under warranty and you do not have the packaging for the receiver

tohand,youcanndtheaboveinformationabouttheunitonthis

sticker.

5. LNB input (IF INPUT)

6. Common Interface for tting one

CI+/CI module for Pay TV cards *

)

7. Video output (CVBS) cinch socket

8. Audio outputs (L/R) cinch sockets

9. USB 2.0 port (USB-A connector)

10. HDMI connection

11. USB 2.0 port (USB-A connector)

12. Network connection (Ethernet)

13. Electrical data stream output

(SPDIF/Sony Philips Digital Interface

Format) for Dolby Digital AC 3 audio

14. Optical data stream output

(SPDIF/Sony Philips Digital Interface

Format) for Dolby Digital AC 3 audio

15. Infra-red sensor connection option **

)

16. Power supply connection (12 V)

17. On/Off switch ***

)

Tip!

HDMI

Cinch

12 of 64

Connect the Sat IF input on the receiver to the satellite reception system.

Use a coaxial cable with an F connector (see the illustration on the right).

Connect the HDMI socket of the satellite receiver to the HDMI socket of the TV set. Alternatively,

you can also make a connection via the video and two audio sockets with the aid of Cinch

cables (see the graphic Connection example).

Graphic: Connection example

Graphic: F connector

6 Connecting the receiver

6.1 Connection of the unit to the TV set

13 of 64

6.2 Audio connection

There are two ways you can access the digital audio.

HDMI

The stereo audio is transmitted to your TV set via the HDMI interface. If your TV set also

supports Dolby Digital, you can also receive the Dolby Digital audio via the HDMI interface

(providing it is broadcast by the channel provider). Refer to the operating instructions for your

TV set for more information.

SPDIF Dolby Digital output (electrical/optical)

The SPDIF outputs are intended for the connection of a Dolby Digital system (see „14 Advanced

connection example“ on p. 55). Connect the SPDIF output (electrical or optical) to the Dolby

Digital system using an appropriate cable.

6.2.1 Digital

6.2.2 Analogue

If you want to play the sound on your hi- system, connect the audio Cinch sockets to the input

sockets on the hi- system, using an appropriate cable (see „14 Advanced connection example“

on p. 55).

SPDIF

Sony Philips Digital Interface Format (digital output

for Dolby Digital AC 3 Audio)

14 of 64

Read sections 1-6 of this manual before you put the UFSconnect 906 into

operation.

Do not connect the unit to the mains until all installation work has been

properly carried out. In the explanation of the item "First Installation" we

assume that the receiver has been connected correctly with due regard for

the above section.

Ifyoudonotknowthecongurationofyoursatellitereceptionsystem,

werecommendyoutocontactyourspecialistdealerfortherst

installation of your receiver.



(green)

Call up the next step in the

rst installation

...

Numeric input



(red)

Go back one step in

the rst installation



Conrm the changed

values/setting;

call up the submenu



Select/change

individual menu

parameters, navigation



Cancel entry, go back

First switch on your TV set. Select at this the AV-/HDMI input you have used to connect the

receiver to your TV set. Switch on the receiver at the power switch on the rear of the unit.

Now perform the rst installation. If you have any questions or encounter problems, contact

your specialist dealer.

7 First Installation

7.1 Buttonsrequiredforremotecontrolduringrstinstallation

7.2 Switch on the TV set and receiver

You will see the following after

switching on the receiver for the

rst time:

Always check the bar at the

bottom of the on-screen display.

These provide information on

what to do next.

Fig: Language Selection

7.3 Step 1: Language Selection

Tip!

15 of 64

Select with



the desired menu language for your UFSconnect 906. Conrm your

selection with the



button. The selected language is indicated with a check mark

(see Fig. "Language Selection").

The following languages are available: German, English, French, Italian, Spanish, Czech,

Dutch, Polish Turkish and Russian.

Press the



(green)buttontogotothenextstepoftherstinstallation.

The following on-screen display appears:

Fig: TV, Video, and Audio

7.4 Step 2: TV, Video, and Audio

Use the



buttons here to select the basic settings for the video and audio output of the

receiver to the TV set.

During this process refer to the operating instructions for your TV set and

take care to select only those settings that your TV set can process.

Video Output via

The rear panel outputs video via the HDMI socket on the unit's rear panel.

HDMI/YPbPr Resolution

Here you can select the video resolution that will be output at the TV set.

Either

► 1080p (resolution 1920 x 1080, full-screen images)

► 1080i (resolution 1920 x 1080, half-screen images)

16 of 64

Force 576i (this must be supported by the TV set otherwise you will not see a TV picture)

You can only and need only make this setting if you have selected the setting "Automatic"

for "HDMI/YPbPr Resolution". If for a programme that is transmitted in the format 720 x 576

(standard TV), the original format is to be transmitted to the TV set, then select the "On" setting.

If the setting is "Off", the programme may be automatically scaled up to the HDTV format 720p

by the receiver.

HDCP for free channels

Select here whether HDCP (digital copy protection) is to be constantly set to "On" with free

channels or is not to be activated, "Off".

TV control box via HDMI (CEC)

If you select "Off", the TV set must be switched on or off separately. If you select "On" the TV set

is automatically switched on as well when starting the receiver. However, this only works if the

TV set is in standby mode. If the receiver is switched off into standby mode, the TV set will also

be switched to standby mode.

Automatically simultaneously switching the TV set on/off by the receiver is available only if the

TV set supports this function!

Show 4:3 Event

Here you can select the type of screen display mode for 4:3 broadcasts on a 16:9 TV set.

Either

► Normal (Pillarbox)

► Stretched (full screen) or

► Zoom in (Pan & Scan)

Audio Format via HDMI

Here you can select the type of audio signal that is transmitted by the HDMI interface.

Select the signal that your TV set can process:

► PCM (Stereo) or

► S/PDIF format (multichannel)

► 720p (resolution 1280 x 720, full-screen images)

► 576p (resolution 720 x 576, full-screen images) or

► Automatic

Auto Dolby Digital Output:

Here you can select whether the receiver should automatically select the Dolby Digital

soundtrack (if this is transmitted).

Press the



(green)buttontogotothenextstepoftherstinstallation.

7 First Installation

17 of 64

7.5 Step3:Tunerconguration

The following on-screen display appears:

Fig: Tuner Conguration

If you are not familiar with the details of your reception system, note the following:

If your receiver is connected up as in the connection example (see the illustration in

"Connecting the receiver" in this section), only one change/selection is necessary in

therestoftherstinstallation.

In many cases the satellite reception system is a DiSEqC™1.0 system. This type

ofsystemispreset.Conrmthecurrenton-screendisplaysusingthe



(green)

button. In conjunction, select with



from the satellite selection the desired

satellite(inGermanythisisusuallyASTRA19.2°East).Conrmyourselectionwith

the



button.Conrmtherestoftheon-screendisplaysduringtherstinstallation

using the



(green) button. You cannot damage your reception system during this

process!

IfthereisnoTVpictureattheendoftherstinstallation,contactyourspecialist

dealer.

Youshouldperformtheantennaconguration/makechangesyourself

only if you are fully familiar with the particulars of your reception system.

Tip!

18 of 64

You can set up the tuner conguration for the following types of reception systems:

► DiSEqC™1.0

► DiSEqC™1.1

► Motorized antenna (DiSEqC™1.2/DiSEqC™1.3 (USALS))

► Single LNB or

► OneCable system

Continueasdescribedintherstinstallationforthetypeofreceptionyouhaveselected.

Item Tuner conguration type

7.5.1 DiSEqC™1.0 Seite 19

7.5.2 DiSEqC™1.1 Seite 21

7.5.3

Motorized antenna:

DiSEqC™1.2/

DiSEqC™1.3 (USALS)

Seite 24

7.5.4 Single LNB Seite 31

7.5.5 OneCable system Seite 33

7 First Installation

19 of 64

7.5.1 DiSEqC™1.0

Fig: Tuner conguration, DiSEqC™1.0

Select with



"DiSEqC™1.0". Press the



(green) button.

The following on-screen display appears:

Number of Satellites

Select the number of



satellites present in the signal at the tuner (four max.).

Go to the "Satellite 1: ....." and press



CongurationSatellite1

Here you perform the settings for the rst satellite for tuner 1.

Satellite and Position:

Select the desired satellite using the



buttons. Alternatively you can press the



button

to view a list of all stored satellites and then select the required satellites from this list.

Fig: Tuner conguration, DiSEqC™1.0, satellite

20 of 64

LNB Type:

If your reception system does not have a universal LNB, use the



buttons to select

the LNB types that are used in your reception system. You can choose from the following

LNB types:

► Universal

► Single or

► User-dened

If you do not use a Universal LNB, press the



button. You can now dene the settings for

your LNB type (single or user-dened).

LNB Frequencies (MHz):

Enter the LNB frequencies (Low/High/Limit) using the number pad. Now use the



button to

save the new values.

DiSEqC™ Repeat:

The setting for how often the DiSEqC™ command must be repeated depends on the

conguration of your reception system.

► Off DiSEqC™ command is not repeated

► 1 DiSEqC™ command is repeated once

► 2 DiSEqC™ command is repeated twice

► 3 DiSEqC™ command is repeated three times

Refer to the documentation for

your LNB or seek assistance from

a specialist engineer.

Test-Transponder:

Here you can select a transponder to check the signal strength bar and signal quality bar to see

whether your settings are correct.

When you have completed all the settings for this satellite, press the



button.

If you have selected more than one satellite (four max.) for Tuner 1, you can now dene the

settings as described above for the rst satellite, for the second satellite and then for the third

and fourth satellites, if selected.

Press the



(green)buttontogotothenextstepoftherstinstallation.

Continuewithitem"„7.6Step4:ChannelSearch“onp.41oftherstinstallation.

Refer to the

documentation

for your reception

system or seek

assistance from

a specialist

engineer.

7 First Installation

Page is loading ...

Kathrein UFSCONNECT 906SW Owner's manual

Brand: Kathrein

Model: UFSCONNECT 906SW

Category: AV receivers

Type: Owner's manual

This manual is also suitable for

UFSconnect 906

Download PDF

report

Kathrein UFSCONNECT 906SW Owner's manual

This manual is also suitable for

Kathrein UFSCONNECT 906SW Owner's manual

Related papers

Other documents