Ranger Products R326H Operating instructions

Brand: Ranger Products

Model: R326H

Category: Air compressors

Type: Operating instructions

This manual is also suitable for

Forward this manual to all operators.

Failure to operate this equipment as

directed may cause injury and/or property

damage.

INSTALLATION AND OPERATION MANUAL

MODELS

R28H

R2513H

R326H

SHIPPING DAMAGE CLAIMS

When this equipment is shipped, title passes to the pur-

chaser upon receipt from the carrier. Consequently,

claims for the material damaged in shipment must be

made by the purchaser against the transportation com-

pany at the time the shipment is received.

BE SAFE

Your new ranger air compressors are designed and built

with safety in mind. However, your overall safety can be

increased by proper training and thoughtful operation on

the part of the operator. DO NOT

operate or repair this

equipment without reading this manual and the important

safety instructions shown inside.

Bend - Pak Inc.

1645 Lemonwood Drive

Santa Paula, CA 93060, U.S.A

Tel: 805 933 9970 - Fax: 805 933 9160

“The Benchmark Of Quality”

AIR

COMPRESSORS

(Home & Hobby)

UPON DELIVERY

1. Carefully remove all packaging material.

2. Inspect the equipment and all parts for any signs of concealed shipment or storage damages.

3. Remember to report any shipping damage to the carrier and make a notion on the delivery receipt.

IMPORTANT SAFETY INSTRUCTIONS

u· Read all warning labels and the operation man-

ual and be thorough on all aspects of the equip-

ment prior to operations.

· Always use proper eyeware and hearing pro-

tection when operating this equipment.

· Before use, on a regular basis check the com-

pressor and all of its components for any dam-

ages and repair or replace all defective or dam-

aged parts.

· Keep hands and all body parts away from the

equipment at all times (Never operate without

the belt guards).

· Maintain a clean work area free from spills,

dampness and any other source of contamina-

tion.

· Make sure this equipment is operated by pro-

fessional personnel only. Keep visitors and

especially children away from work area.

· Electric shock hazard:

Never use the compressor without connection

to a properly grounded outlet with the specified

voltage and fuse protection.

Do not use the compressor in a wet or explo-

sive environment.

Never attempt maintenance or adjustment with

the power connected or the equipment in oper-

ation.

· Tank safety valve:

This valve is factory installed to prevent the air

receiver from damage should a malfunction

occur in the compressor pump.

It is factory set a specific limit for your particu-

lar model and adjustment, and should never

be tampered with. Adjustment by user will auto-

matically void the warranty.

· Pressure switch:

The air pressure switch is set at the factory for

optimum performance of your equipment.

Never bypass or remove this switch, as serious

personal injury or equipment damage could

result from too high pressure.

· Motor and compressor pump:

Air compressor gets hot while in operation.

Never touch the motor, discharge tubing, or

compressor pump while in operation.

The compressor operates automatically while

the power is connected.

Never attempt any adjustment with power on.

Never operate the compressor with the belt

guard removed.

· Compressed air caution:

Compressed air from the unit may contain car-

bon monoxide. Air produced is not suitable for

breathing purposes.

Always use a respirator when spraying paint or

chemicals.

Always wear safety glasses or goggles when

spraying air.

· Air receiver:

Over pressurizing the air receiver could cause

an explosion or rupture. To protect from over

pressurizing, a factory preset safety valve is

included. DO NOT REMOVE, MAKE ADJUST-

MENT OR SUBSTITUTIONS FOR THIS

VALVE.

Occasionally pull the ring on the valve to make sure

that the valve operates freely. If the valve does not

operate freely, it must be replaced. Never weld to, drill

into or change the air receiver in any way.

Changing or tampering with any of the above men-

tioned conditions may result in voiding of the manufac-

turer's warranty. Be advised that any replacement parts

should be purchased with the same specifications as

the original equipment. Please contact your authorized

dealer for replacement parts or specifications.

SPECIFICATIONS / FEATURES

HOME / HOBBY

Models: R28H / R2513H / R326H-601

Model Motor Max PSI/BAR

Max CFM @

90PSI/LM

Max CFM @

115PSI/LM

Tank Dimentions Ship

Weight

R28H

2hp / 50-60Hz /

110V

115PSI

8 BAR

7.3 CFM

207 LM

7 CFM

198 LM

8 Gal

30 L

W13-3/8"xL23-3/4"xH25-3/4"

W340mm x L603mm x H654mm

63 Lbs

29 Kg

R2513H

2.5hp / 50-60Hz /

110V

115PSI

8 BAR

8.8 CFM

249 LM

8.5 CFM

241

13 Gal

50 L

W15-1/4"xL27"xH25-3/4"

W387mm x L686mm x H654mm

69 Lbs

31 Kg

R326H-601

3 hp / 60Hz* /

110V

145PSI

BAR

8.7 CFM

246 LM

8.3 CFM

235

26 Gal

100 L

W18"xL43-1/4"xH37"

W457mm x L1099mm x H940mm

216 Lbs

98 Kg

* 50 hz model available upon request

ASSEMBLY INSTRUCTION

There is no assembly required. This compressor is completely pre-assembled at the factory.

Installation and Location:

Locate the compressor in a clean, dry and well ventilated area. The compressor should be located 12” to 18” from a

wall or any other obstruction that would interfere with the air flow through the fanbladed belt-wheel. Place the com-

pressor on a firm, level surface. The compressor is designed with heat dissipation fins which allow for proper cooling.

Keep the fins and other parts that collect dust and dirt clean. A clean compressor runs cooler and provides longer

service. Do not place rags, containers or other materials on top of the compressor which would obstruct ventilation

openings for proper compressor operating temperature.

For Vertical Type Only: For permanent installation, the compressor should be bolted to the floor through holes pro-

vided in the compressor feet. Shims must be used to level the compressor before bolting it to the floor. Severe vibra-

tion will result when the compressor is bolted down tightly and the feet are not level. This can lead to welds cracking

or fatigue failure of the air receiver.

BELT ADJUSTMENT:

Install the triangular belt and adjust it so when pres-

sure is applied onto center, there should be 1/2”

(approx.) slack. See sketch

Note: If the belt is installed too tightly, overloading of

the motor will occur. This will cause the motor to

overheat. If the belt is installed too loosely it will slip

and unstable operation and vibration will occur.

Caution: The rotating direction for the flywheel must

follow the arrow shown on the beltguard.

OPERATION INSTRUCTIONS

GENERAL DESCRIPTION OF OPERATION:

To compress air, the pistons move up and down in the

cylinder. On the down stroke air is drawn in through the

inlet valve. The discharge valve remains closed. On the

upstroke of the piston, air is compressed. The inlet air

closes and compressed air is forced out through the dis-

charged valve, through the check valve into air receiver.

Working air is not available until the compressor has

raised the air receiver above that required at the air

service connection. The air inlet filter openings must be

kept clear of obstructions, which could reduce air deliv-

ery of the compressor.

Depending on the CFM requirements of the tools used,

your new air compressor can be used for operating paint

sprayers, air tools, grease guns, air brushes, caulking

guns, sandblasters, inflating tires and inflatable toys,

spraying weed killer and insecticides, etc. An air pres-

sure regulator is usually necessary for most of these

applications.

IT IS STRONGLY ADVISED, BEFORE OPERATING THE COMPRESSOR THE FOLLOWING POINTS ARE

CAREFULLY CHECKED. (Daily)

1. Check to see that all nuts and bolts are snug.

2. Check to see if the belt is installed properly, with proper tension.

3. Check if the oil level is full.

4. Check if the compressor is fixed on a strong, stable level base.

5. Check if the oil breather is clean.

6. If the air filter is dirty it should be replaced or cleaned.

7. Check if the flywheel can be turned easily and smoothly.

INITIAL START-UP PROCEDURE:

Open the air receiver service valve to permit air to escape, preventing air pressure build-up in the air receiver.

Plug power supply cord into correct power source.

Close air receiver service valve. Your compressor is now ready for operations.

Run the compressor for a minimum of twenty (20) minutes in this no-load position to lubricate the bearings and

pistons.

MAINTENANCE

Before doing any maintenance or adjustments to your air compressor please ensure you have discon-

nected electrical power and drained the tank of pressure.

1. DAILY OR BEFORE EACH USE:

Check oil level.

Drain condensation from tank.

Check for any unusual noise or vibration.

Be sure all nuts and bolts are tight.

2. WEEKLY:

Clean air filter by opening air filter cap, remov-

ing the filter element and cleaning it thoroughly

with soap and water. Rinse thoroughly and

allow to dry completely before assembly. Old fil

ter should be replaced.

Clean breather hole on oil check dipstick.

3. MONTHLY:

Adjust belt tension if needed and replace belt

if worn.

Inspect air system for leaks by applying soap

to all joints. Tighten those joints if leakages are

observed.

4. 250 HOURS OR SIX (06) MONTHS (Which

ever comes first):

Change compressor oil.

Replace often if compressor is used near paint

spraying operations or in dusty environment.

COMPRESSOR LUBRICATION:

Note: Do not add or change oil while the compressor is

in operation. Use only the recommended SAE 20 or 30

weight non-detergent oil.

COMPRESSORS WITH OIL LEVEL GAUGE:

1. Turn the oil filling plug counter clockwise, pull it out.

2. The compressor is full when the oil level is between

the marks “H” and “L”. Replace oil filling plug.

3. Always maintain oil level between the mark “H” and

“L” in the oil glass.

DRAINING THE OIL:

1. Remove the oil drain plug and allow the oil to drain

completely.

2. Replace the oil drain plug. (we recommend use of a

sealing compound or Tefflon tape to avoid leakage).

3. Refill with the recommended oil, to proper level.

CHECKLIST

During the breaking-in period, nuts and bolts have a tendency

to loose up.After two weeks tighten all nuts and bolts including head

bolts. Then check everything once a month to make sure all nuts and

bolts stay tight.

TROUBLE POSSIBLE CAUSE

CORRECTIVE ACTION

No start condition

Fuse blown or circuit

Breaker tripped

Loose electrical

Connection

Overheated motor

Check for cause of blown fuse or

breaker and replace or reset

Check wiring connections

Press reset button or wait for

automatic reset. Check V belt

tension.

Low pressure Air leak in safety valve

Loose tube or fitting

Restricted air filter

V belt loose

Defective check valve

Check valve manually by pulling

upward on rings. If condition

persists, replace valve.

Tighten fittings.

Clean or replace as necessary.

Adjust belt tension.

Replace check valve.

Safety valve

releasing

Defective pressure

switch or improper

adjustment

Check for proper adjustment and if

problem persists, replace pressure

switch.

Oil discharge in

air

Improper oil viscosity

Crankcase overfilled

Compressor

overheated

Restricted air filter

Worn piston rings

Replace oil with 20-30 weight non –

Detergent oil

Drain crankcase and fill to proper

level.

Air pressure regulated too high.

Clean or replace filter.

Replace piston rings.

Excessive V-belt

Wear

V-belt too loose

V-belt too tight

Motor pulley out of

Alignment

Adjust for proper tension.

Adjust for proper tension

Alignment motor pulley by adjusting

the position of electric motor.

TROUBLESHOOTING

NO. Parts NO. Description Q'ty

42 6011620 In-six Angle Bolt 4

1 6011640 In-six Angle Bolt 4 43 60016 Spring Washer 4

2 60016 Spring Washer 4 44 6024614 Washer 4

3 504012C Air Filter 1 45 403863 Cable Flap 1

4 50051234C Exhaust Elbow 1 46 403963 Cable Conduct 1

5 5101AD15 Cylinder Head

47 4017Y254 Pres. Adjt.Connecter 6

6 5102AD15 Gasket,Cylinder Head 1 48 402150 Cable Nut 1

7 510347 Valve Seat 2 49 408522650 Ele.Cable 1

8 510647AD Al.Gasket 1 50 40062S22 Ele.Cable 1

9 510438 Valve Plate 2 51 20T025N221 Air Tank 1

10 5107AD15 Gasket,Cylinder 1 52 200624120 Handle 1

11 52014740 Cylinder 1 53 301014 Safety Valve 1

12 60068 Six Angle Nut 2 54 30011414C Manifole 1

13 60018 Spring Washer 2

3004114 PRessure Switch 1

14 6013838 Stud 2 55a 6021412 Screw,Cross recess head 1

15 5214AD15 Gasket,Cylinder 1 55b 3004U2 Clip 2

1840AD

Piston Ring Set

55c 3004U1 PRessure Switch cover 1

17 520347 Compressor Ring 2

55d

3004114 PRessure Switch body 1

18 520447 Qil Ring 1 56 30032012L Pressure Gauge 1

19 520247 Piston 1 57 203314A Nipple 2

20 52071238 Piston Pin 1 58 30031512L Pressure Gauge 1

21 601812 Retainer,Piston 2 59 30051414B Pressure Adjuster 1

22 5206AD Connecting Rod 1 60 300214B Air Cock 1

23 5308AD20 Crankshaft 1 61 20-20SF Coupler 1

24 60018 Spring Washer 1 62 50041234C Nut 2

6011840

In-six Angle Bolt 1 63 500212500 Exhaust Pipe 1

26 533320R Beather 1 64 500312 Coller 1

27 60141824 "o" Ring 1 65 201612B Check Valve 1

28 5301AD15 Crankcase 1 65a 202112 Check Valve Cover 1

29 532012 Oil Leveler 1 65b 201912 Al.Washer 1

30 6014263 "o" Ring 1 65c 202012 Check Valve Spring 1

31 5318810 Drain Plug

65d 201812 Check Valve Rod 1

32 53198 Drain Plug Gasket 1 65e 201712 Check Valve Elemt 1

33 6011822 In-six Angle Bolt 4 66 302106580 Unload Pipe 1

34 60018 Spring Washer 4 67 30226716 Unload Nut 1

R28H Air Compressor Parts List

NO. Parts NO. Description Q'ty NO. Parts NO. Description Q'ty

1 6011640 In-six Angle Bolt 4 43 60016 Spring Washer 4

2 60016 Spring Washer 4 44 6024614 Washer 4

3 504012C Air Filter 1 45 403863 Cable Flap 1

50051234C

Exhaust Elbow 1 46 403963 Cable Conduct 1

5 5101AD15 Cylinder Head

47 4017Y254 Pres. Adjt.Connecter 6

6 5102AD15

Gasket,Cylinder Head

1 48 402150 Cable Nut 1

7 510347 Valve Seat 2 49 408522650 Ele.Cable 1

8 510647AD Al.Gasket 1 50 40062S22 Ele.Cable 1

9 510438 Valve Plate 2 51 20T025N221 Air Tank 1

10 5107AD15 Gasket,Cylinder 1 52 200624120 Handle 1

11 52014740 Cylinder 1 53 301014 Safety Valve 1

12 60068 Six Angle Nut 2 54 30011414C Manifole 1

13 60018 Spring Washer 2

3004114 PRessure Switch 1

14 6013838 Stud 2 55a 6021412

Screw,Cross recess head

15 5214AD15 Gasket,Cylinder 1 55b 3004U2 Clip 2

1840AD

Piston Ring Set

55c

3004U1

PRessure Switch cover

17 520347 Compressor Ring 2

55d

3004114 PRessure Switch body 1

18 520447 Qil Ring 1 56 30032012L Pressure Gauge 1

19 520247 Piston 1 57 203314A Nipple 2

20 52071238 Piston Pin 1 58 30031512L Pressure Gauge 1

21 601812 Retainer,Piston 2 59 30051414B Pressure Adjuster 1

22 5206AD Connecting Rod 1 60 300214B Air Cock 1

23 5308AD20 Crankshaft 1 61 20-20SF Coupler 1

24 60018 Spring Washer 1 62 50041234C Nut 2

6011840

In-six Angle Bolt 1 63 500212500 Exhaust Pipe 1

26 533320R Beather 1 64 500312 Coller 1

27 60141824 "o" Ring 1 65 201612B Check Valve 1

28 5301AD15 Crankcase 1 65a 202112 Check Valve Cover 1

29 532012 Oil Leveler 1 65b 201912 Al.Washer 1

30 6014263 "o" Ring 1 65c 202012 Check Valve Spring 1

31 5318810 Drain Plug

65d 201812 Check Valve Rod 1

32 53198 Drain Plug Gasket 1 65e 201712 Check Valve Elemt 1

33 6011822 In-six Angle Bolt 4 66 302106580 Unload Pipe 1

34 60018 Spring Washer 4 67 30226716 Unload Nut 1

35 5307AD15 Drain Plug Gasket 1 68 203018716 Unload Elbow 1

4M070410PA

Elec Motor

69 201514 Drain Cock 1

37 401815 Over-Load 1 70

2005520 Foot Rubber Pad 2

38 401914146 Motor Fan 1 71

60026 6 Flat Washer 2

39 4.016E+09 Capacitor 1

72 6021616 M6x1x16 Screw 2

40 4.028E+09 Capacitor Cover 1

2002612W Tank Wheel 2

2012CP1525

Moter PV Cover 1

200310 Wheel Lock Cap 2

42 6011620 In-six Angle Bolt 4

R2513H Air Compressor Parts List

No. Parts No. Description Q'ty No. Parts No. Description Q'ty

1 6011650 In-Six Angle Bolt 8 37 532012 Oil Leveler 1

2 60016 Spring Washer 8 38 531814 Oil Drain Plug 1

3 5101UB20 Cylinder Head 2 39 5312UB20

Gasket, Bearing Cover

4 504012D Air Filter Assy 2 40 5317UB20 Oil Plug Seal 1

5 6011830 In-Six Angle Bolt 4 41 5316UB20 Oil Plug 1

6 60028C Copper Washer 4 42 5301UB20 Crankcase 1

7 5102UH20 Gasket, Cylinder Head 2 43 60176304 Bearing 1

8 510357 Valve Seat 4 44 5308UB30 Crankshaft 1

9 510647AD Al. Gasket 2 45 60176205 Bearing 1

10 510457 Valve Plate 4 46 6016UB20 Oil Seal 1

5107UB10A

Gasket, Cylinder 2 47 5307UB20 Gasket, Bearing Seat 1

12 52015146 Cylinder 2 48 5306UB20 Bearing Seat 1

13 60068 Six Angle Nut 8 49 533318 Breather 1

14 60016 Spring Washer 8 50 60018 Spring Washer 4

15 6013832 Stud 8 51 6005820 Bolt 4

16 5214UB20 Gasket, Cylinder 2 52

53021024A1

Pulley 1

17 520051 Piston Ring Set 2 53 5304UB10 Washer,Pulley 1

18 520351 Compressor Ring 4 54 60018L Spring Washer 1

19 520451 Oil Ring 2 55 6005840L Bolt 1

20 520251 Piston 2 56 01UB30 Pump 1

21 52071244 Piston Pin 2 57 6005825 Bolt 4

22 601813 Piston Pin Clip 4 58 60018 Spring Washer 4

23 5206UB20 Connecting Rod 2 59 201612B Check Vavle 1

24 5213UB20 Splasher 2 60 203018716 Unload Copper Pipe 1

25 6021510 Screw,Cross recess head 2 61 2001UE30A Plate Seat 1

26 20321234 Exhaust, 3-Way 1

20T100N032

Air Tank 1

27 50041234C Exhaust Nut 1

2002616B Tank Wheel 2

28 50051234 Exhaust Elbow 1

600216 Washer 2

29 501012235

Copper Pipe Assy, Exhaust

6003181 Split Pin 2

30 500312 Cooler 1

201514 Drain Cock 1

31 500212235 Exhaust Pipe 1

6005815 Bolt 4

32 50041234 Exhaust Nut 2

60028 Washer, Pully 4

33 6005625 Bolt 4

2002U3 Tank Wheel 1

34 60016 Spring Washer 4

3004111 Pressure Switch 1

35 5313UB20 Bearing Cover 1

3003214S Pressure Gauge 1

36 532112 Washer, Oil Leveler 1

301014 Safety Valve 1

36 532112 Washer, Oil Leveler 1

R326H-601 Air Compressor Parts List

R326H601 Air Compressor Parts List

No. Parts No. Description Q'ty

73 203314A Nipple 1

74 30011214B Manifole 1

75 300214B Air Cock 2

76 302106510 Unload Elbow 1

77 302218716 Unload Pipe Nut 1

78 4E152116 Elec. Motor 1

79 6031625 In-six Angle Bolt 1

40023519A1

Motor Pulley 1

81 6023820 Motor Bolt 4

82 6023825 Motor Bolt 4

83 60028 Washer 8

84 60068 Six Angle Nut 8

85 2008205 Motor Base 2

86 2011105 Safety Guard Seat S 1

87 2011105 Safety Guard Seat S 1

88 4004A48 V-Belt 1

89 6005815 Bolt 8

90 60028 Washer, Pully 8

91 2009600S Safety Guard 1

92 400523 Ele.Cable 1

93 400522 Ele.Cable 1

94 4017Y254 Pres. Adjt Connecter 16

95 501012470 Exhaust Pipe Assembly 1

95a 50041234C Exhaust Pipe Nut 2

95b 500212470 Exhaust Pipe 1

95c 500312 Cooler 47

96 203314A Nipple 2

97 30051414B Pressure Adjuster

30051414B2

Pressure Adjuster

3003214L Pressure Gauge

Ranger Products R326H Operating instructions

Brand: Ranger Products

Model: R326H

Category: Air compressors

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Ranger Products R326H Operating instructions

This manual is also suitable for

Ranger Products R326H Operating instructions

Related papers

Other documents