Digimerge DPD14W User manual

V I S I O N

POLARIS

model: DPD14W

LIMITATION OF LIABILITY

THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN

ALL RESPECTS, HOWEVER, WE CANNOT ASSUME RESPONSIBILITY FOR ANY

CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION

CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS

OR NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE

SUCH CHANGES.

ii

- iii -

WARNINGS AND CAUTIONS:

CAUTION:

CAUTIONCAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER(OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is

intended to alert the user to the presence of uninsulated "dangerous voltage"

within the product's enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to

the presence of important operating and maintenance (servicing) instructions in the

literature accompanying the product.

Should any liquid or solid object fall into the cabinet,

unplug the unit and have it checked by the qualified

personnel before operating it any further.

Unplug the unit from the wall oulet if it is not going to

be used for several days or more. To disconnect the

cord, pull it out by the plug. Never pull the cord itself.

Allow adequate air circulation to prevent internal heat

build-up. Do not place the unit on surfaces (rugs,

blankets, etc.) or near materials(curtains, draperies)

that may block the ventilation holes.

Height and vertical linearity controls located at the

rear panel are for special adjustments by qualified

personnel only.

Do not install the unit in an extremely hot or

humid place or in a place subject to excessive

dust, mechanical vibration.

The unit is not designed to be waterproof.

Exposure to rain or water may damage the unit.

Clean the unit with a slightly damp soft cloth.

Use a mild household detergent. Never use

strong solvents such as thinner or benzine as

they might damage the finish of the unit.

Retain the original carton and packing

materials for safe transport of this unit in the

future.

Safety ----------------------------------------- Installation -----------------------------------

Cleaning --------------------------------------

PRECAUTIONS

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR

MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR

OTHER OPENINGS ON THE EQUIPMENT.

FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTED

AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL

DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE

LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION

AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS

OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT

GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY

ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH

THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE

TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN

A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL

INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO

CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.

CAUTION : CHANGES OR MODIFICATIONS NOT EXPRESSLY

APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE

COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN

ICES-003.

NORME NMB-003 DU CANADA.

WARNING

This is a Class A product. In a domestic environment this product

may cause radio interference in which case the user may be required

to take adequate measures.

CE COMPLIANCE STATEMENT

FCC COMPLIANCE STATEMENT

- iv -

IMPORTANT SAFEGUARDS

1 -1 Class 2 power source only.

7

-2 Do NOT use power source other than

17

that specified.

17. CAUTION-these servicing instructions are

for use by qualified service personnel only.

to reduce the risk of electric shock do not

perform any servicing other than that contained

in the operating instructions unless you are

qualified to do so.

5. ACCESSORIES

- v -

- 1 -

INTRODUCTION

IMPORTANT : The user of this camera is responsible for

checking and complying with local, state, and federal laws

and statutes concerning the recording and monitoring of

audio signals.

The camera provides high-quality images using PIXIM DPS(Digital Pixel System) 1/3" Wide

Dynamic Range Sensor.

Features:

High resolution and high performance 1/3" CMOS(PIXIM DPS) technology

Wide Dynamic Range(WDR)

Excellent picture quality

Minimal blooming

Zero smear

Built-in NTSC/PAL video encoder

540 lines(Color) of resolution

0.5 Lux(Color) @ F1.2 Sensitivity

Upto 1/22,000sec electronic shutter at f/1.2

OSD (On Screen Display)

Auto white balance modes

Day & Night (Auto / OFF)

AGC (Auto Gain Control)

VIDEO OUT(BNC)

Internal/AC line lock

Operates in 12VDC or 24VAC

Use Certified / Listed Class 2 power supply only.

2.8-12mm Day/Night A/I Varifocal Lens F1.4

Camera Mount : camera mount directily to the wall or ceiling

Test Monitor Output

PACKAGE CONTENTS

The package contains the following.

Camera in Housing 1

Instruction Manual (This Document) 1

Accessory Kit for Installing 1

1Drilling guide label

- 2 -

- 3 -

CAMERA CONNECTIONS

1. Lens : 2.8-12mm D&N A/I Vari-focal lens for wide area monitoring.

2. Power : 24V AC input / 12V DC input

power source from a DC 12V or AC 24V ac +/-10% 60/50Hz +/-1Hz

Use Certified/Listed Class 2 power supply transformer only.

*If using DC 12V power adaptor,

use a power supply capable of supplying 6 Watts.

3. Video : BNC connector used to connect the camera to a monitor, switcher, etc.

1

2

3

1

2

3

6

0

360

3

6

0

360

The camera module can be moved horizontally,

vertically and rotated 360 degrees to achieve any viewing angle.

3-Axis Camera Construction

The camera module can be moved horizontally,

vertically and rotated 360 degrees to achieve any viewing angle.

3-Axis Camera Construction

180

- 4 -

BASE INSTALLATION

Dome body

Liner

1. Make mounting holes and cable hole in the place (ceiling or wall) to which this

dome camera is installed using the Drilling guide label.

- 5 -

2.

Push the liner on the sides where the patterns are put in the teeth of a comb

and pull it out.

To remove dome cover, turn the dome body counterclockwise until locators

reach end of travel and pull off.

Screw Tapping (M6)

Drilling Guide Label

Plastic anchor

l

t o

Dri

ling

Posi i

n(P

A5)

WALL

- 5 -

OPERATING CAMERA

Down Button

Up

Enter

Right

Left

1

2

3

4

5

1

2

3

4

5

- 6 -

Spot Video Out

6

3. Attach the housing to the ceiling using suitable fasteners, M6x35 tapping

screws are supplied only use if they are suitable.

Turn the housing to right direction about 16 degrees to lock in place.

4. The assembly of the dome body and liner is in reverse order of disassembly.

Finally, lock dome body with locking screw(M3X5) from the accessory kit.

The housing can also

be mounted on a 4s

electrical box.

MOUNTING HOUSING TO

AN ELECTRICAL BACK BOX

Electrical box

Torx screws

UNC 8-32 x 0.75

Note: Electrical box is not supplied.

- 7 -

CAMERA SETUP

PRESETS

NORMAL

INDOOR

OUTDOOR

WD NORMAL

AGC LOW

NORMAL

HIGH

WHITE BALANCE

ATW Normal

ATW Xtnd

AWB

SYNC

INTERNAL

LINELOCK

AUTO

OFF

D/N CONTROL

SAVE. EXIT. CANCEL

PUSH AWB CONFIRM

> Save AWB & ALL Chngs.

CANCEL

''' WARNING '''

will

ALL User

be written to ROM

properties

LINELOCK MENU

V PHASE

DAY/NIGHT THRESHOLD SETUP

IN

OUT

- 8 -

CAMERA ADJUSTMENT

Setting can be made using the 5 buttons located on the back of the camera.

1) PRESETS

1) The CAMERA SETUP is displayed on the monitor when press and hold

the ENTER button for more than 1 second.

2) Press the UP and DOWN buttons in the vertical direction and move the cursor(>)

to the desired submenu.

3) ".." indicated submenus.

- NORMAL

- WD NORMAL Standard video with Wide Dynamic Range Limit Max

- INDOOR To brighten the video taken indoors

Standard video

Auto Gain Control selected (LOW / NORMAL / HIGH)

2) AGC

- DEFAULT

Standard video

- INDOOR

To brighten the video taken indoors

- OUTDOOR

3) WHITE BALANCE

hite balance is automatically followed up

- A T W Normal

W

(Limits the range of auto tracking by the value of two properties).

When shooting in a bright area outdoors

W

- ATW Xtnd hite balance is automatically followed up.

- AWB One-push automatic white balance control.

Shoot a target white subject and press the ENTER button,

and the white balance will be adjusted.

4) SYNC

- OUTDOOR When shooting in a bright area outdoors

- INTERNAL

This mode is necessary for using the internal synchronization.

- LINELOCK

This mode is necessary for the operation of multi camera because

it synchronizes the camera phase by using the external signal

(AC Signal).

5) D/N CONTROL

- AUTO

This camera has a function which automatically changes to

the appropriate mode for daytime or night-time.

- OFF

In this mode, the camera outputs the video image only in color.

- 10 -

Fixed mount

Day & Night AUTO / off

Lens

2-Pin wire / 2-Pin terminal block

f=2.8~12mm F1.4, Varifocal DC auto iris ICR

0.5 Lux(Color), 0.01 Lux(B/W) @ F1.2, 50IRE

o o o o

]

-10 C ~ +50 C [14 F ~ 122 F

PRESETS

Default / Indoor / Outdoor

ATW Normal / ATW Xtnd / AWB

/ WD Normal

Normal /

50302659A

540TV Lines WDR Super High Resolution

Day & Night Color Camera

EXTERNAL DIMENSION

Dimensions

Window Size

Cable Entry

Weight - Unit:

Shipping:

Unit: mm

0.1 in. (2.5mm thick),

impact-resistant P.C (LEXAN)

3.93 in. (10cm) diameter

One 1" opening holes

0.88 lb. (0.4kg)

1.41 lb. (0.64 kg)

145.6

100 (Inner)

113

59

Digimerge DPD14W User manual

Digimerge DPD14W User manual

Related papers

Other documents