2. Eurolux
  3. D92

Eurolux D92 Owner's manual

  • Hello. I'm a chat assistant and I've analyzed the provided user manual for the eurolux D92 and D93 Gypsum Square Recessed Down Lights. This document is a guide that describes the installation, specifications and maintenance of the downlights. I am ready to answer any questions you may have about the product details, safety instructions or installation process described in this manual.
  • What type of lamp is compatible with these downlights?
    What are the voltage requirements for this luminaire?
    What is the IP rating of these downlights?
    What is the cut-out size for the D92 model?
    What is the cut-out size for the D93 model?
Gypsum Square Recessed Down Lights
ILLUSTRATIONS
Excluding 1 x GU10 max 35W 230V
D92
D92
D93
D93
D92 / D93
PRODUCT CODE
Please read instructions before commencing installation and retain for future reference.
Cape Town - 9 Racecourse Road, Milnerton, 7441
Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065
www.eurolux.co.za
12V~MR16 Max 35W GX5.3
D92
10.3cm
10.3cm
4
3
2
1
5CM
min.
20CM min.
5CM
min. 18CM
min.
12mm
12V
ATTENTION:
D93 12V
12V~ MR-16 MAX 35W GX5.3
4
3
2
1
12.3cm
12.3cm
5CM
min.
20CM min.
5CM
min. 18CM
min.
12mm
• Fitting Material: Gypsum
• Fitting Colour: White
• Lamp type: Excluding 1 x GU10 Max 35W 230V
• Voltage: 220V - 240V ~ 50Hz.
• Protection against electric shock: Class 3
• IP Rating: 20. Protected against solid foreign objects of 12.5mm Ø and greater.
• Commercial / domestic use
• Not suitable for outdoor use
• Maximum ambient temperature range: 20ºC - 40ºC
• Dimensions: D92 - (L)102mm x (W)102mm x (D)26mm
D93 - (L)122mm x (W)122mm x (D)55mm
• Cut-out: D92 - 103mm x 103mm
D92 - 103mm x 103mm
D92 / D93 - attachments:
If the external exible cable or cord of this luminaire is damaged, it should be exclusively replaced
by the manufacturer or his service agent or a similar qualied person in order to avoid a hazard.To
ensure that you get maximum longevity and maximum use out of your luminaire, please observe
the following safety instructions.
Electrical products can cause death, injury, or damage to property. Installation of the luminaire
must be carried out by a qualied electrician, in accordance with SANS 10142. On completion
of installation, ensure that the Certicate of Compliance is updated.
• Before connecting the luminaire, ensure that voltage indicated on the rating label
corresponds with the mains voltage in your home.
• When changing the lamp, ensure that the power is turned o.
• Ensure that the correct lamp type and wattage is tted.
• This luminaire is checked in full for conformity to the quality standards and safety requirements.
• The manufacturer / supplier is not responsible for any damage of properties and
persons, caused by the incorrect use or installation of the luminaire.
• Should you be unsure of how to install this luminaire correctly, please consult a
professional electrician or your supplier for assistance.
• Ensure all items/ components, threads and screws are tightly secured.
IMPORTANT:
• Tampering with this luminaire, i.e using silicon sealers or incorrect cabling, will
invalidate your warranty.
• When the protection glass is damaged, it should be replaced immediately.
• Please check whether the connection of the power cord is safe and reliable before installation.
• If your mains wiring diers in any way from diagram luminaire, consult a qualied electrician.
• Always ensure that the mains supply voltage is correct.
• Always replace the lamp with one of an identical rating and wattage.
• Choking hazard: May contain small parts. Keep away from children.
SPECIFICATIONS
IMPORTANT SAFEGUARDS
INSTALLATION
CLEANING
• Before cleaning always ensure the power supply is turned o.
• Do not immerse the luminaire in water.
• No abrasive products, solvents, detergent may be used to clean this luminaire.
• Ensure that the tting does not come in contact with corrosive chemicals, etc.
• Use a soft cloth to clean.
Before installation always ensure the power supply is turned o.
1 Cut a hole in the ceiling as per ‘‘cut out”.make sure there are no beams or structures were
you will be cutting the holes.
2 Connect Live (brown / red), Neutral (blue / black) to terminal block provided, connect Earth
(green / yellow) to earth terminal.
Ensure all connections are tight and safe.
3 Hold both clips on either side of downlight upwards and insert downlight into ceiling hole
ensuring the mains lead is not trapped.
4 Push tting upwards to snap rmly into position,ush with ceiling.
5 Insert the lamp by location the pin connection holes within the lamp
holder,gently pushing the lamp into holder and sliding into place.
6 Reconnect power.
NOTE:
Always allow the lamp to cool suciently before changing. To avoid heat transfer from downlight,
allow a minimum gap of about 200mm in height from downlight to ceiling / any materials above the
downlight and 200mm all around side of the downlight. Failure to do so could result in re.
• Do not insert your ngers or any part of your body into the electrical contact and
sockets of this product whilst it is connected to the electrical supply.
• Item may vary slightly from the picture on the carton.
ENVIRONMENTAL PROTECTION
Waste electrical & Electronic equipment regulations requires that any of our products
showing this marking must not be disposed of with other household or commercial
waste. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate any such products from other waste
types and recycle it responsibly at your local facilities.
/