ekwb EK-Quantum Momentum² VRM Bridge ROG Maximus Z690 Formula White Upgrade Kit Installation guide

Category
Computer liquid cooling
Type
Installation guide
USER GUIDE
EK-Quantum
Momentum2 VRM Bridge ROG Maximus Z690 Formula White Upgrade
- 2 -
Please note the installation of the product is intended to be undertaken
by an adequately trained and experienced person. You are installing the
product at your own risk. If you are not properly trained or experienced
or feel unsure about the installation procedure, please refrain from
installing the product yourself and contact our tech support for
assistance. We disclaim our liability for any damages to the product as
well as incidental, consequential, or indirect damages incurred due to
improper or inappropriate installation.
Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
The EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets
The use of corrosion-inhibiting coolants is always
recommended for liquid cooling systems and mandatory for
nickel-plated water blocks
Do not use pure distilled water!
For best results, EK recommends the use of EK-CryoFuel
coolants! To reach optimal performance, make sure to
thoroughly bleed the air out of your water block!
- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
DIFFERENCE BETWEEN Z690 AND Z790 PUSH-IN ADAPTERS 4
REPLACING THE PUSH-IN ADAPTERS 5
REPLACING THE STANDOUT 6
SUPPORT AND SERVICE 8
SOCIAL MEDIA 8
- 4 -
BOX CONTENTS
DIFFERENCE BETWEEN Z690 AND Z790 PUSH-IN ADAPTERS
Push-in Adapter (2 pcs) Led strip 130/100 mm (1 pc)
Replacement standout assembly (1 pc)
11.2 mm
26.8 mm
9.2 mm
24.8 mm
EK-Quantum Torque Push-In Adapter Z690; EAN: 3831109895863 EK-Quantum Torque Push-In Adapter Z790; EAN: 3831109911150
- 5 -
STEP 2
The CPU water block requires replacement of the two (2) currently
used Push-in Adapters with spares.
Push-in Adapters on the VRM Bridge must remain the same.
STEP 2
STEP 1
To replace the Push-in adapters, it is necessary to remove the
Monoblock first.
To detach the Monoblock, unscrew one (1) M4 x 18 DIN7991 Screw
and slide the Plexi part away from the standout (approximately 3mm).
REPLACE
REPLACING THE PUSH-IN ADAPTERS
STEP 1
ALLEN KEY M2.5
PLEXI PLATE
M4 x 18 DIN7991
SCREW
- 6 -
STEP 2
Position the LED strip in the marked spot on the replacement
standout.
To stick the LED strip, make sure to peel off the protective
tape first. The LED strip should be inserted through the slot
from the backside of the standout.
STEP 2
STEP 1
To replace the Z690 Standout, unscrew three (3) M3 x 6 ISO 7380
Screws using provided Allen Key 2mm and detach the standout with
LED Strip.
A replacement LED Strip is included in the package in case the
original one gets damaged.
REPLACING THE STANDOUT
STEP 1
M3 x 6 ISO 7380
LED STRIP
Z690 STANDOUT
(BLACK)
For this step, you will need:
Allen Key 2 mm
- 7 -
STEP 3
Position the replacement standout with the LED Strip to the water
block. Using Allen Key 2mm and three (3) M3 x 6 ISO7830 Screws
secure the standout. Do not use excessive force!
STEP 3
REPLACEMENT
STANDOUT
M3 x 6 ISO7830
SCREW
INSERT LED STRIP
CONNECTOR
Allen Key 2 mm M3 X 6 ISO 7380
Screw (3 pcs)
Replacement stand-
out + LED Strip
For this Step, you will need:
In case you need assistance or wish to order spare parts or a new
mounting mechanism, please contact:
https://www.ekwb.com/customer-support/
EKWaterBlocks
@EKWaterBlocks
ekwaterblocks
ekwaterblocks
EKWBofficial
SUPPORT AND SERVICE
SOCIAL MEDIA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ekwb EK-Quantum Momentum² VRM Bridge ROG Maximus Z690 Formula White Upgrade Kit Installation guide

Category
Computer liquid cooling
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI