Intesis IN703DAL0640000 User manual

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

IN703DAL0640000 GATEWAY CONFIGURATION GUIDE

INTESIS MAPS USER MANUAL

Version 1.0.2

Publicaon date 2023-12-01

ENGLISH

Disclaimer

The informaon in this document is for informaonal purposes only. Please inform HMS Networks of any

inaccuracies or omissions found in this document. HMS Networks disclaims any responsibility or liability for any

errors that may appear in this document.

HMS Networks reserves the right to modify its products in line with its policy of connuous product

development. The informaon in this document shall therefore not be construed as a commitment on the

part of HMS Networks and is subject to change without noce. HMS Networks makes no commitment to update

or keep current the informaon in this document.

The data, examples and illustraons found in this document are included for illustrave purposes and are only

intended to help improve understanding of the funconality and handling of the product. In view of the wide

range of possible applicaons of the product, and because of the many variables and requirements associated

with any parcular implementaon, HMS Networks cannot assume responsibility or liability for actual use

based on the data, examples or illustraons included in this document nor for any damages incurred during

installaon of the product. Those responsible for the use of the product must acquire sucient knowledge in

order to ensure that the product is used correctly in their specic applicaon and that the applicaon meets all

performance and safety requirements including any applicable laws, regulaons, codes and standards. Further,

HMS Networks will under no circumstances assume liability or responsibility for any problems that may arise as

a result from the use of undocumented features or funconal side eects found outside the documented scope

of the product. The eects caused by any direct or indirect use of such aspects of the product are undened and

may include e.g. compability issues and stability issues.

Table of Contents

1. Introducon ........................................................................................................................... 1

2. Prerequisites .......................................................................................................................... 2

3. Installaon ............................................................................................................................. 3

4. Create a New Project from a Template ........................................................................................ 4

5. Main Menu Overview .............................................................................................................. 6

6. Conguraon Tab .................................................................................................................... 7

6.1. General .......................................................................................................................... 7

6.1.1. General Conguraon ................................................................................................ 8

6.1.2. Connecon .............................................................................................................. 8

6.1.3. USB Host ................................................................................................................. 8

6.1.4. Time Conguraon .................................................................................................... 9

6.1.5. Security .................................................................................................................. 9

6.1.6. Secondary BMS Protocol ............................................................................................ 9

6.1.7. Wiring Diagram ....................................................................................................... 11

6.2. BMS Protocol Conguraon .............................................................................................. 11

6.2.1. BMS Protocol: BACnet ............................................................................................... 11

6.2.1.1. BACnet Server General Conguraon ................................................................... 12

6.2.1.2. Gateway Mode ................................................................................................ 12

6.2.1.3. BACnet Advanced Conguraon .......................................................................... 12

6.2.1.3.1. Nocaon Class ...................................................................................... 13

6.2.1.3.2. Calendars ................................................................................................ 17

6.2.1.3.3. Schedules ................................................................................................ 18

6.2.1.3.4. Trend Logs ............................................................................................... 21

6.2.2. BMS Protocol: Modbus ............................................................................................. 23

6.2.2.1. Modbus Conguraon ....................................................................................... 23

6.2.2.2. RTU Conguraon ............................................................................................ 23

6.2.2.3. TCP Conguraon ............................................................................................. 24

6.3. DALI Protocol Conguraon ............................................................................................... 25

6.3.1. DALI Conguraon ................................................................................................... 25

6.3.1.1. DALI Channel ................................................................................................... 26

6.3.1.2. ECGs .............................................................................................................. 27

6.3.1.2.1. Add ECGs on Channel ................................................................................ 27

6.3.1.2.2. Failsave Conguraon ................................................................................ 29

6.3.1.2.3. ECG Idencaon ..................................................................................... 29

6.3.1.2.4. Common ECG Parameters ........................................................................... 33

6.3.1.2.5. Delete and Clone ECGs ............................................................................... 34

6.3.1.3. Input Devices ................................................................................................... 34

6.3.1.3.1. Add Input Device on Channel ...................................................................... 34

6.3.1.3.2. Delete, Clone, and Copy Input Devices .......................................................... 35

6.3.1.3.3. Input Devices Local Conguraon ................................................................ 36

6.3.1.3.4. Input Device Parameters ............................................................................ 44

6.3.1.4. Input Device Instances ...................................................................................... 44

6.3.1.4.1. Delete, Clone, and Copy Instances ................................................................ 45

6.3.1.4.2. Instance Conguraon ............................................................................... 46

6.3.1.4.2.1. Instance Type: Push Buon ................................................................. 46

6.3.1.4.2.2. Instance Type: Absolute Input .............................................................. 47

6.3.1.4.2.3. Instance Type: Occupancy Sensor ......................................................... 48

6.3.1.4.2.4. Instance Type: Light Sensor ................................................................. 49

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2

6.3.2. DALI Commissioning ................................................................................................. 49

6.3.2.1. DALI Bus Scanning ............................................................................................ 51

6.3.2.2. Discovered Devices Idencaon and Address Associaon ....................................... 52

6.3.2.3. Add Discovered Devices to the Project ................................................................. 52

7. Connecon Tab ...................................................................................................................... 55

8. Signals Tab ............................................................................................................................ 57

9. Receive/Send Tab ................................................................................................................... 58

10. Diagnosc Tab ...................................................................................................................... 59

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2

1. Introducon

Intesis MAPS© is a soware tool for conguring and monitoring the Intesis® gateways. Intesis MAPS has been

designed and developed in-house, assuring an up-to-date tool to get all the potenal of our gateways.

NOTE

Intesis MAPS is compable with Windows® 7 and higher.

The design of this conguraon tool focuses on four main pillars:

• A user-friendly interface.

•Mulple ways to create your project:

– From scratch, using a template.

–Imporng data from your computer.

– Downloading the sengs from an already congured gateway.

• Full linkage between the control system and the device installaon signals.

•Real-me monitoring of the device network.

Introducon INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2 Page 1 of 60

2. Prerequisites

To congure the gateway, you need:

• The items supplied by HMS Networks:

– Intesis IN703DAL0640000 gateway

– Gateway documentaon:

•Installaon sheet: www.intesis.com/docs/installaon-sheet-in703dal064000

• User manual: www.intesis.com/docs/user-manual-in703dal064000

– USB Mini-B type to USB A type cable to connect the gateway and the computer.

NOTE

You can use an Ethernet cable instead (not included).

• A computer to run the conguraon tool Intesis MAPS.

NOTE

Requirements:

– Windows 7 or higher

– Hard disk free space: 1 GB

– RAM: 4 GB

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Prerequisites

Page 2 of 60 INTESIS MAPS USER MANUAL Version 1.0.2

3. Installaon

Downloading the soware

1. Enter the Intesis MAPS secon on the Intesis webpage: hps://www.intesis.com/products/intesis-maps

2. Fill out the form.

3. Check the consent box (I hereby give consent for HMS to process my data).

4. Click the DOWNLOAD MAPS buon.

5. A .zip le will be downloaded to your computer.

Installing the soware

1. Click the ZIP le to open it.

2. Double-click the EXE le.

3. The Intesis MAPS Setup Wizard will guide you through the steps required to install Intesis MAPS on your

computer:

a. Read the license agreement and select I Agree.

b. Select the installaon folder.

4. Once the installaon is completed, click the Close buon.

Installaon INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2 Page 3 of 60

4. Create a New Project from a Template

1. Open Intesis MAPS.

2. Click Create New Project in the Geng started menu on the le.

You can create a project from scratch using a template. To nd the appropriate template, lter the search

by:

• Clicking on the protocol logos, depending on the desired applicaon.

• Typing the order code IN703DAL0640000 in the Order Code eld.

NOTE

The order code is printed on the silver label placed on the gateway's right side.

• Looking for the Project Name IN-BAC-DALI-64 or IN-MBS-DALI-64 on the list.

Figure 1. Three possibilies for the template selecon

3. Select the desired template.

4. Click Next or double-click the template on the list.

NOTE

Templates are just examples of integraon. Depending on the type of integraon, you may have to

modify some parameters.

IMPORTANT

Don't forget to save your project on your computer before exing Intesis MAPS. To do so, go to

Project → Save or Save As. Later on, you can load the project to Intesis MAPS and connue with the

conguraon.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Create a New Project from a Template

Page 4 of 60 INTESIS MAPS USER MANUAL Version 1.0.2

Create a New Project from a Template INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2 Page 5 of 60

5. Main Menu Overview

Figure 2. Intesis MAPS main menu

The following secons provide an overview of the ve tabs that compose the Intesis MAPS main menu. Through

these opons, you will congure both the gateway and your project, and monitor that everything works ne

using the Diagnosc tab.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE Main Menu Overview

Page 6 of 60 INTESIS MAPS USER MANUAL Version 1.0.2

6. Conguraon Tab

Find on the le side of the Conguraon tab a menu with three opons:

•General: Congure the general parameters of the gateway.

•Building management system (BMS) protocol: Modbus or BACnet,

depending on your project's current applicaon. In the case of the image

on the le, the control system is based on Modbus.

•DALI: Congure the parameters for DALI.

6.1. General

Figure 3. General conguraon menu on the Conguraon tab

Use this menu to congure some general parameters of the gateway.

TIP

Toolp: Hover the cursor over a eld, and a message will appear indicang the purpose of the

parameter.

Conguraon Tab INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2 Page 7 of 60

6.1.1. General Conguraon

•Gateway Name: Type a descripve name for your gateway.

•Project Descripon: Type a short descripon of your project.

6.1.2. Connecon

NOTE

When commissioning the gateway for the rst me, DHCP will be enabled for 30 seconds. During

that me, if there is a DHCP server, an IP address will be automacally assigned to the gateway. If

there is no DHCP, you can type an IP address of your choice. Aer that me, the default IP address

192.168.100.246 will be automacally set.

You can nd this default IP address wrien in the installaon sheet.

•Enable DHCP: Use this opon for networks that have a DHCP server.

Uncheck this opon to unlock the following parameters:

–IP Address: Assign a xed IP address for the gateway.

–Net Mask: Set the gateway IP netmask.

–Default Gateway: Set the default route assigned to the gateway.

NOTE

The Default Gateway parameter is oponal, but you must dene the gateway route when a

connecon to the internet or to other networks is needed.

•Password: Click the Change buon and follow the instrucons to set a password for the gateway.

6.1.3. USB Host

Click the Edit buon to open the USB Mode Conguraon.

Buon A Funconality

•Auto Capture logs in USB (enabled by default): Capture logs by pressing the gateway's buon A.

–Capture Spons (enabled by default): Spontaneous values are logged.

–Capture Communicaon (enabled by default): Protocol communicaon is logged.

–Debug Level: Choose the debug level (0 .. 255. Default value: 1).

•Save project in USB (enabled by default): Save the project to the USB together with the logs.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE General

Page 8 of 60 INTESIS MAPS USER MANUAL Version 1.0.2

Buon B Funconality

•Download project to the gateway (enabled by default): Download a project from a USB ash drive to the

gateway by pressing the gateway's buon B.

•Download Firmware to the gateway (enabled by default): Download a rmware version from a USB ash drive

to the gateway by pressing the gateway's buon B.

IMPORTANT

The gateway's USB port only admits the connecon of a USB ash drive. No external hard disks or

similar are allowed.

Click Apply to save the changes.

6.1.4. Time Conguraon

•Set current PC me to the gateway: Connect the gateway to your PC and click the Set buon to set the

gateway's clock with your PC's current me.

•Time sync on project download (disabled by default): The gateway's clock is set to your PC me when

downloading the project to the gateway.

6.1.5. Security

•Edit Security Conguraon: Click the Edit buon to open the Security Conguraon window.

IMPORTANT

We recommend keeping the predetermined conguraon.

–Disable UPD Discover Service (disabled by default): The gateway is not discoverable through UDP

communicaon.

–Disable TCP Console Service (disabled by default): The gateway stops communicang with the conguraon

and diagnosc soware through TCP. This only applies to gateways supporng connecon to the PC via both

Ethernet and console ports.

–Disable HTTPS Cercates Auto Update (enabled by default): Automac updates for the HTTPS cercates

are not allowed.

Click Save to save the changes.

6.1.6. Secondary BMS Protocol

IMPORTANT

This funcon applies to BACnet to DALI applicaons only.

1. Click the Edit buon to add a secondary BMS protocol based on Modbus.

2. On the Secondary BMS Protocol Management window, select Modbus Slave.

3. Click Apply to save the changes.

The new opon Secondary BMS Protocol MAP appears.

• Click the View buon on this second opon to view the Extra protocol Map Summary window.

The table lists the signals for the BMS, the secondary BMS, and the device protocols.

•View Internal Columns (enabled by default): Hide/show the BACnet Server column.

General INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2 Page 9 of 60

•View External Columns (enabled by default): Hide/show the DALI column.

•View Secondary BMS Protocol Columns (enabled by default): Hide/show the Modbus Master column.

NOTE

Click the Export buon to save an Excel copy of the table on your computer.

The menu on the le now shows Modbus Slave (MBS):

Conguraon parameters for the secondary BMS:

Modbus Conguraon

•Type: TCP (RTU opon is not allowed).

•Byte Order 32 bits registers. Choose between:

–Big Endian (default value)

–Lile Endian

–Word Inv BE (word inverted Big Endian)

–Word Inv LE (word inverted Lile Endian)

•Nocaon on MB Write. Select when the Modbus write nocaon will be sent to the device protocol:

–Always

–On Change of Value (default value)

•Select Modbus register base. Choose between:

–0 based (default value)

–1 based

TCP Conguraon

•Port: Set the port for communicaon between the gateway and the Modbus TCP system.

NOTE

The default port is 502.

•Keep Alive: Set the me in minutes before sending a keep-alive message (1 to 1440. Default value: 10 min).

NOTE

Set the parameter to 0 to disable this funcon.

•Slave Number: Set the Modbus Slave Address (1 to 255. Default value: 1).

MBS Summary

•View MBS Extra Protocol Summary: Click the View buon to open the Extra protocol Map Summary window.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE General

Page 10 of 60 INTESIS MAPS USER MANUAL Version 1.0.2

NOTE

See above for details.

•Select registers format. Choose between:

–16 bits unsigned (default value)

–32 bits oat

6.1.7. Wiring Diagram

•Check Gateway's Wiring Diagram: Click the View buon to open the schemac image on how to wire the

gateway.

6.2. BMS Protocol Conguraon

6.2.1. BMS Protocol: BACnet

For this applicaon, the gateway acts like a BACnet server device.

BMS Protocol Conguraon INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2 Page 11 of 60

6.2.1.1. BACnet Server General Conguraon

•Device Name: Type a descripve name for your gateway.

•Device Instance: Set the BACnet device object instance property. This is a unique idener for the gateway

inside a single BACnet network segment (0 to 4194302. Default value: 246).

•Password: Click the Change buon and follow the instrucons to set a password for the gateway.

•Objects Informaon: Click Show to see a table with the type of objects available.

•Disable BACnet password (not recommended) (parameter disabled by default): Disable the BACnet password.

IMPORTANT

Keep the BACnet password enabled to ensure the security of the gateway and the installaon.

6.2.1.2. Gateway Mode

•Mode: Select the communicaon type.

–IP (default value): IP communicaon over Ethernet.

•UDP Port: Select the UDP port for the BACnet/IP communicaon.

NOTE

The UDP port is set to 47808 (BAC0 in hexadecimal) by default.

•Network Role (disabled by default): Dene the gateway behavior regarding other network elements.

IMPORTANT

If you are unfamiliar with these opons, please leave the parameter as Disabled to avoid

issues with the BACnet communicaon/conguraon.

–Disabled: The gateway provides no special service regarding network communicaon or sengs.

–Foreign Device: The gateway acts as a foreign device from the BACnet network point of view.

–BBMD: The gateway acts as a BBMD in the BACnet network.

–MS/TP: Serial communicaon over the EIA-485 bus.

•Baudrate: Select the communicaon speed: Auto, 9600, 19200, 38400, 57600, 76800, or 115200 bps.

NOTE

The baudrate is set to Auto by default.

•Max. Masters: Set the highest master MAC address in the MS/TP network (1 .. 127. Default value: 127).

•Max. Info Frames: Set the maximum number of messages that can be sent onto MS/TP network per

token pass (1 .. 100. Default value: 1).

•MAC Address: Set the MAC address of the gateway in the MS/TP network (0 .. 127. Default value: 1).

•Edit MSTP Timeouts: Click Edit to open the MSTP Timeouts Conguraon window.

–PFM Timeout: Set the polling for master meout in milliseconds (20 .. 100 ms. Default value: 60 ms).

–TP Timeout: Set the token passing meout in milliseconds (20 .. 100 ms. Default value: 60 ms).

6.2.1.3. BACnet Advanced Conguraon

Show Advanced Conguraon: Open advanced conguraon parameters (disabled by default).

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE BMS Protocol Conguraon

Page 12 of 60 INTESIS MAPS USER MANUAL Version 1.0.2

IMPORTANT

These sengs are for advanced users only. We recommend leaving the predetermined

conguraon.

6.2.1.3.1. Nocaon Class

Click Edit to open the Nocaon Class Conguraon parameters.

Figure 4. Nocaon Class Conguraon window

Click the buon to create up to ten Nocaon_Class objects. For each one, you can set:

•Object Name: Type a name for the Nocaon_Class.

•Object Instance: Sets the BACnet object instance for the Nocaon_Class.

•Recipient List: Click the buon to create eight dierent BACnet desnaons. For each one, you can set:

–Desnaon Name: Type a descripve name for the BACnet desnaon.

–Transions: Select which transions will force this Nocaon_Class to be acve:

•O_normal (disabled by default): When the status changes from o to normal.

•Fault (disabled by default): When the status changes to fault.

•Normal (disabled by default): When the status changes from fault to normal.

–Recipient Type: Select the type of desnaon:

•Device (default value): The recipient is a device. Select the device instance number for this device in the

Object Instance text box.

•Address (IP): The recipient is set using the specic address on BACnet/IP. Specify:

–Network Number (0 .. 65535. Default value: 0).

BMS Protocol Conguraon INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2 Page 13 of 60

–IP address (192.168.100.10 by default) and Port (47808 by default) for the desnaon.

– Set the desnaon as a Global Broadcast (disabled by default).

– Set the desnaon as a Broadcast (disabled by default).

•Address (MS/TP): The recipient is set using the specic address on BACnet MS/TP. You'll have to specify:

–Network Number (0 .. 65535. Default value: 0).

–MS/TP MAC Address (0 .. 255. Default value: 0).

– Set the desnaon as a Global Broadcast (disabled by default).

– Set the desnaon as a Broadcast (disabled by default).

•Address (Other): The recipient is set using another type of address. You'll have to specify:

–Network Number (0 .. 65535. Default value: 0).

–Other Address.

– Set the desnaon as a Global Broadcast (disabled by default).

– Set the desnaon as a Broadcast (disabled by default).

•BACDesnaon Advanced Opons (disabled by default): Check this opon to show some advanced opons.

–Valid days: Sets the days for receiving the nocaon.

–From: Sets the starng point for the valid period.

–To: Sets the ending point for the valid period.

–Issue Conrmed Nocaons (disabled by default): Determines if nocaon events are sent as Conrmed

or Unconrmed to the BACnet desnaon.

IMPORTANT

Sending them as Conrmed requires Ack.

•Nocaon Class Advanced Opons (disabled by default): Check this opon to show the Ack Required

opons.

–O_Normal (disabled by default): Enable the acknowledgment for the TO_OFF_NORMAL event.

–Fault (disabled by default): Enable the acknowledgment for the TO_FAULT event.

–Normal (disabled by default): Enable the acknowledgment for the TO_NORMAL event.

NOTE

Set the priority for each parameter (0 .. 255. Default value: 140).

Once you have created and congured the needed Nocaon_Class objects, the next step is to assign them to

signals:

1. Go to the Signals tab.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE BMS Protocol Conguraon

Page 14 of 60 INTESIS MAPS USER MANUAL Version 1.0.2

2. Click the Edit Columns buon from the boom menu.

3. In the Select Visible Columns window, check NC.

4. Click Save.

A new column named NC is now visible.

5. Look for the signal to which you want to assign the Nocaon_Class object and click the corresponding cell

in the NC column.

6. Click the buon.

7. In the Select Nocaon Class window, uncheck the Empty parameter.

BMS Protocol Conguraon INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE

INTESIS MAPS USER MANUAL Version 1.0.2 Page 15 of 60

8. Use the dropdown menu to select the Nocaon_Class object.

9. Set the rest of the parameters:

NOTE

These parameters vary depending on the signal type.

•Nofy Type: Choose if the nocaon is sent as an Alarm (default) or an Event.

•Time Delay: Set the me in seconds before launching the nocaon (0 .. 65535. Default value: 0

seconds).

•Event Enable: Click in the eld to enable/disable the following opons:

–TO_OFF_NORMAL (enabled by default): Enable/disable the TO_OFF_NORMAL event.

–TO_FAULT (enabled by default): Enable/disable the TO_FAULT event.

–TO_NORMAL (enabled by default): Enable/disable the TO_NORMAL event.

•Feedback Value: Choose if the feedback value is Acve or Inacve (default).

•High Limit (Disabled by default): Enable this parameter to set the high limit for the nocaon.

•Low Limit (Disabled by default): Enable this parameter to set the low limit for the nocaon (0.00 ..

999.00).

•Deadband: Set the deadband for the nocaon.

10. Click Save to save the changes.

Once assigned, the instance number of the Nocaon_Class object appears in the NC column.

INTESIS MAPS: CONFIGURATION AND MONITORING SOFTWARE BMS Protocol Conguraon

Page 16 of 60 INTESIS MAPS USER MANUAL Version 1.0.2

Page is loading ...

Intesis IN703DAL0640000 User manual

Intesis IN703DAL0640000 User manual

Related papers

Other documents