2. Anybus
  3. AWB3000
AWB3000

Anybus AWB3000, Wireless Cable Kit Installation guide

  • Hello! I've reviewed the Anybus Wireless Cable Kit startup guide and I'm ready to assist you. This document details the installation process, including the RJ45 connector assembly and cable color coding, as well as the configuration steps using Easy Config Mode for setting up the Bluetooth connection and assigning LAN IP addresses. Feel free to ask me any questions you have about it.
  • What is the correct voltage range for the power supply?
    What does the blue color on the power cable represent?
    What is the purpose of the shielding tape when assembling the RJ45 connector?
    How do you set up unit 1 in Easy Config mode?
    How do you set up unit 2 in Easy Config mode?
© 2020 HMS Industrial Networks SP2463 1.3 en-US / 2020-08-12 / 19469
Step 1: Installation
This document does not include the complete instructions for the safe use of the described
equipment. Make sure that you have read and understood the safety instructions in the user
documentation for the described equipment before proceeding.
Power Cable
Connecting power with reverse polarity or using the wrong type of power supply may damage the
equipment. Make sure that the power supply is connected correctly and of the recommended type.
Color Function
Brown Power + (9–30 V)
Blue Power Ground
Ethernet Cable
Color Function
Orange/White Transmit +
Green/White Receive +
Orange Transmit -
Green Receive -
Anybus®Wireless Cable Kit
STARTUP GUIDE
© 2020 HMS Industrial Networks SP2463 1.3 en-US / 2020-08-12 / 19469
Assembling the RJ45 connector
1. Slide the pressure nut and plug housing over the cable.
If the cable should pass through any walls or enclosures, thread the cable through the openings
and apply cable glands as required before continuing.
2. Fold back the braided shield and apply shielding tape around the cable sheath end. Make sure
that the tape does not protrude over the stripped part of the cable.
3. Trim the braided shield just behind the shielding tape.
Anybus®Wireless Cable Kit Startup Guide 2 (8)
© 2020 HMS Industrial Networks SP2463 1.3 en-US / 2020-08-12 / 19469
4. Untwist the wires and insert them all the way into the wire block so that the wire block meets
the cable end.
Observe the wire color coding printed on the wire block
5. Press the shielding lugs together over the cable end to hold the connector in place and trim the
wire ends close to the wire block.
6. Press the wire block firmly into the connector assembly until it snaps into place.
Anybus®Wireless Cable Kit Startup Guide 3 (8)
© 2020 HMS Industrial Networks SP2463 1.3 en-US / 2020-08-12 / 19469
7. Pull the plug housing over the connector assembly until the housing snaps into place on both
sides of the connector.
8. Tighten the pressure nut firmly by hand.
Anybus®Wireless Cable Kit Startup Guide 4 (8)
© 2020 HMS Industrial Networks SP2463 1.3 en-US / 2020-08-12 / 19469
Step 2: Configuration
Setting up unit 1 in Easy Config Mode 1
1. Power on the first unit and wait for the Link Quality LEDs to light up and go out again, then
immediately press and release MODE.
2. LED Ashould now be lit. Otherwise, press MODE repeatedly until only LED Ais lit.
3. Press and hold MODE for 2 seconds to confirm Easy Config mode 1.
4. LED Awill blink while the unit is scanning for the second unit.
Anybus®Wireless Cable Kit Startup Guide 5 (8)
© 2020 HMS Industrial Networks SP2463 1.3 en-US / 2020-08-12 / 19469
Setting up unit 2 in Easy Config Mode 4
The second unit must be set up within 120 seconds of the first unit.
5. Power on the second unit and wait for the Link Quality LEDs to light up and go out again, then
immediately press and release MODE.
6. Press MODE repeatedly until only LED Cis lit.
7. Press and hold MODE for 2 seconds to confirm.
8. LED Cwill blink until the units have established Bluetooth communication.
Anybus®Wireless Cable Kit Startup Guide 6 (8)
© 2020 HMS Industrial Networks SP2463 1.3 en-US / 2020-08-12 / 19469
Step 3: Validation
The two units should now be paired as Bluetooth clients (PANU-PANU) and will have the LAN IP
addresses 192.168.0.99 and 192.168.0.100.
The blue BT LED should be lit on both units.
Bluetooth link quality will be indicated with the A-B-C-D LEDs on both units.
For further information about the configuration of wireless and Ethernet communication as well as
PROFINET optimization and PROFISAFE, please refer to the user manual and other related
documentation available at www.anybus.com/support.
Anybus®Wireless Cable Kit Startup Guide 7 (8)
last page
© 2020 HMS Industrial Networks
Box 4126
300 04 Halmstad, Sweden
[email protected] SP2463 1.3 en-US / 2020-08-12 / 19469
/