Rugged Ridge Windshield CB Radio Mount Installation guide

Brand
Rugged Ridge
Model
Windshield CB Radio Mount
Type
Installation guide

Rugged Ridge Windshield CB Radio Mount

The Rugged Ridge Windshield CB Radio Mount is designed to provide a sturdy and convenient mounting solution for CB radios in 2003-2006 Jeep TJ/LJ models. Here's an overview of its capabilities:

  • Secure Mounting: The mount securely attaches to the windshield frame using well nuts and long screws, ensuring a stable platform for your CB radio.

  • Compatibility: It is specifically designed to fit 2003-2006 TJ/LJ models, ensuring a precise fit and seamless integration with your vehicle.

  • Easy Installation: The included instructions provide clear and concise steps for easy installation, requiring basic tools like a drill and screwdriver.

Rugged Ridge Windshield CB Radio Mount

The Rugged Ridge Windshield CB Radio Mount is designed to provide a sturdy and convenient mounting solution for CB radios in 2003-2006 Jeep TJ/LJ models. Here's an overview of its capabilities:

  • Secure Mounting: The mount securely attaches to the windshield frame using well nuts and long screws, ensuring a stable platform for your CB radio.

  • Compatibility: It is specifically designed to fit 2003-2006 TJ/LJ models, ensuring a precise fit and seamless integration with your vehicle.

  • Easy Installation: The included instructions provide clear and concise steps for easy installation, requiring basic tools like a drill and screwdriver.

Copyright © 2016 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
CB Radio Mount, 2003-2006 TJ/LJ
Page 1/3
Part # 13551.07
OMIX-ADA® TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649 | EMAIL: [email protected]
FOR WARRANTY INFORMATION VISIT: www.Omix-Ada.com
CONTENTS:
• CB Radio Mount (1)
TOOLS REQUIRED:
• Drill
• 3/8” Drill Bit
• Phillips Head
Screwdriver
• Utility Knife
HARDWARE:
• Well Nut (2)
• Long Screw (2)
• Short Screw (2)
• Washer (2)
• Locknut (2)
Washer x 2
Well Nut x 2
Short Screw x 2
Long Screw x 2
Locknut x 2
CB Radio Mount x 1
Careful attention is required to this instruction or operation, but does not generally
relate to pesonal injury. Damage to your product or other property may result if
you do not follow instructions.
NOTICE
Copyright © 2016 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
CB Radio Mount, 2003-2006 TJ/LJ
Page 2/3
3. Clean the area and insert well nuts in the newly
drilled holes. Collapse the well nuts by screwing in
the long screws provided. Remove the screws before
proceeding.
2. Drill out the rivets holding the footman loop with a
3/8” drill bit and remove the footman loop.
1. Retract soft top, position sun visors against the side
windows, and pry off the plastic windshield trim by
gently pulling along it until all the clips release.
NOTICE
Use caution when drilling out rivets to not
drill through the windshield frame and to
ensure best possible t of product.
Copyright © 2016 Omix-Ada®, Inc.
460 HORIZON DR. SUITE 400 | SUWANEE, GA 30024 | PHONE: 770-614-6101 | FAX: 770-614-6069 | [email protected]
CB Radio Mount, 2003-2006 TJ/LJ
Page 3/3
6. Install CB Radio, or other accessories, using the
short screws, washers, and locknuts supplied.
NOTE: Be sure not to obstruct the rear view mirror.
5. Cut off center tab on the plastic windshield trim
with a utility knife and reinstall on windshield frame.
4. Remove plastic liner from mounting tape, allign
mounting holes, and install CB Radio Mount on the
windshield frame. Place footman loop over the CB
Radio Mount and fasten to frame with the long screws
provided.
NOTICE
Use caution when cutting tab to ensure
no damage is done to trim.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Rugged Ridge Windshield CB Radio Mount Installation guide

Brand
Rugged Ridge
Model
Windshield CB Radio Mount
Type
Installation guide

Rugged Ridge Windshield CB Radio Mount

The Rugged Ridge Windshield CB Radio Mount is designed to provide a sturdy and convenient mounting solution for CB radios in 2003-2006 Jeep TJ/LJ models. Here's an overview of its capabilities:

  • Secure Mounting: The mount securely attaches to the windshield frame using well nuts and long screws, ensuring a stable platform for your CB radio.

  • Compatibility: It is specifically designed to fit 2003-2006 TJ/LJ models, ensuring a precise fit and seamless integration with your vehicle.

  • Easy Installation: The included instructions provide clear and concise steps for easy installation, requiring basic tools like a drill and screwdriver.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents