Real Cable HDS-12 User manual

HDS Series

Installation manual

1

Preface

Disclaimer

As Navico is continuously improving this product, we retain the right to make changes to the

product at any time which may not be reected in this version of the manual. Please contact

your nearest distributor if you require any further assistance.

It is the owner’s sole responsibility to install and use the instrument and transducers in a

manner that will not cause accidents, personal injury or property damage. The user of this

product is solely responsible for observing safe boating practices.

NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES

DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY

CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW.

Governing Language: This statement, any instruction manuals, user guides and other

information relating to the product (Documentation) may be translated to, or has been

translated from, another language (Translation). In the event of any conict between any

Translation of the Documentation, the English language version of the Documentation will be

the ofcial version of the Documentation.

This manual represents the product as at the time of printing. Navico Holding AS and its

subsidiaries, branches and afliates reserve the right to make changes to specications

without notice.

Copyright

Feedback from you

Your feedback is important and helps Navico ensure that this manual is a valuable resource

for all marine technicians. E-mail your comments or suggestions about this manual to the

following address: [email protected]

Warranty

• The warranty card is supplied as a separate document.

• It is shipped with the product registration card.

• In case of any queries, refer to the brand web site of your display or system.

www.lowrance.com

2

Declaration of Conformity

GB

Hereby, Navico Holding AS declares that this HDS is in compliance

with the essential requirements and other relevant provisions of Directive

1999/5/EC.

FI

Navico Holding AS vakuuttaa täten että HDS tyyppinen laite on

direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien

direktiivin muiden ehtojen mukainen.

NL

Hierbij verklaart Navico Holding AS dat het toestel HDS in

overeenstemming is met de essentiële eisen en de andere relevante

bepalingen van richtlijn 1999/5/EG.

FR

Par la présente, Navico Holding AS déclare que ce HDS est conforme

aux exigences essentielles et aux autres dispositions de la directive

1999/5/CE qui lui sont applicables.

SE

Härmed intygar Navico Holding AS att denna HDS står i

verensstämmelse med de väsentliga egenskapskrav och övriga relevanta

bestämmelser som framgår av direktiv 1999/5/EG.

DK

Undertegnede Navico Holding AS erklærer herved, at følgende udstyr

HDS overholder de væsentlige krav og øvrige relevante krav i direktiv

1999/5/ EF.

DE

Hiermit erklärt Navico Holding AS, dass sich dieses SE8, in

Übereinstimmung mit den grundlegenden Anforderungen und den

anderen relevanten Vorschriften der Richtlinie 1999/5/EG bendet.

(BMWi)

GR

Με την παρουσα Navico Holding AS δηλωνει οτι HDS συμμορφωνεται

προς τις ουσιωδεις απαιτησεις και τις λοιπες σχετικες διαταξεις της

οδηγιας 1999/5/ΕΚ.

IT

Con la presente Navico Holding AS dichiara che questo HDS è

conforme ai requisiti essenziali ed alle altre disposizioni pertinenti

stabilite dalla direttiva 1999/5/CE.

ES

Por medio de la presente Navico Holding AS declara que el HDS cumple

con los requisitos esenciales y cualesquiera otras disposiciones aplicables

o exigibles de la Directiva 1999/5/CE.

PT

Navico Holding AS declara que este HDS está conforme com os

requisitos essenciais e outras provisões da Directiva 1999/5/CE.

The equipment named in this declaration, is intended for use in international waters as well as

coastal sea areas administered by countries of the E.U. and E.E.A. A full Declaration can be

obtained from www.lowrance.com

Disposal

Waste Electrical and Electronic Equipment (WEEE) The use of the WEEE

Symbol indicates that this product may not be treated as household waste.

By ensuring this product is disposed of correctly, you will help protect the

environment. For more detailed information about the recycling of this

product, please contact your local authority, your household waste disposal

service provider or the shop where you purchased the product.

3

Contents

Preface .....................................................................................................1

Declaration of Conformity .............................................................................................2

Disposal .........................................................................................................................2

Introduction ........................................................................................... .5

About this Manual .........................................................................................................5

Important Safety and Warning Information ...................................................................5

Check the Parts ..............................................................................................................6

Overview ........................................................................................................................7

Display Installation ................................................................................9

Mounting location ..........................................................................................................9

Panel Mount ...................................................................................................................11

Bracket Mount ...............................................................................................................12

Transducer Installation .........................................................................14

Recommended Tools and Supplies ................................................................................14

Skimmer Installation Instructions ..................................................................................15

System Architecture ...............................................................................28

Wiring the HDS ..................................................................................... .29

Wiring Guidelines ..........................................................................................................29

Power/Data Cable ..........................................................................................................30

NMEA 0183 Wiring Table .............................................................................................31

NMEA 0183 wiring ......................................................................................................31

NMEA 2000 wiring .......................................................................................................32

Ethernet ..........................................................................................................................33

HDS-8 & HDS-10 Data Bridging ..................................................................................34

Single Station .................................................................................................................35

Dual & Multi Station .....................................................................................................36

Connecting HD Radar ....................................................................................................37

Connecting BR24 Radar ...............................................................................................38

Commissioning Check List ............................................................................................39

Sonar ..............................................................................................................................41

4

Dimensional Drawings .......................................................................... .43

HDS5 .............................................................................................................................43

HDS7 .............................................................................................................................44

HDS8 .............................................................................................................................45

HDS10 ...........................................................................................................................46

NMEA Information ............................................................................... .47

NMEA 2000 PGN List ...................................................................................................47

Supported NMEA 0183 sentences .................................................................................49

5

Introduction

About this Manual

• This manual is a reference guide for installing a Lowrance HDS System.

• The information in this manual at the time of printing is correct to the best of our

knowledge. Navico can not be liable for any inaccuracies or missing information.

• Due to the constant improvement of Navico’s products. Navico cannot be liable for

changes between the product and the manual. Refer to www.lowrance.com for

the latest manuals and addendum’s.

Important Safety and Warning Information

Please read carefully before use.

When navigating the vessel, use the Lowrance HDS system only as a

navigational aid. Proper navigation of the vessel is the sole responsibility of the

vessel operator.

The electronic chart used by the HDS System is an aid to navigation only and

is designed to supplement, not replace, ofcial government charts. Only ofcial

government charts supplemented by notices to mariners contain the information

required for safe and prudent navigation. Always supplement the electronic

information provided by the Lowrance HDS with other plotting sources such

as observations, depth soundings, radar and hand compass bearings. Should the

information not agree, the discrepancy must be resolved before proceeding any

further.

Never operate the HDS in Simulate Mode while you are underway. It is the

user’s responsibility to ensure that Simulate Mode is used only in safe situations

such as when you are moored in a marina.

The Global Positioning System (GPS) is operated by the US Government which

is solely responsible for its operation, accuracy and maintenance. The GPS

system is subject to changes which could affect the accuracy and performance

of all GPS equipment anywhere in the world.

The accuracy of the Sonar depth display can be limited by many factors,

including the type of transducer, the location of the transducer, and water

conditions. Ensure that the transducer is installed correctly and the Sonar is used

correctly.

HDS units intended for sale and operation in the America’s region DO NOT

include full functionality outside of the America’s, dened as 30 degrees west

longitude and 180 degrees west longitude. Units are restricted to operate in

English language only with imperial (non-metric) units only.

For full use around the globe an International unit must be purchased from

outside of the America’s region.

6

Check the Parts

Packaged Parts List

HDS Head Unit

Models: 5”, 7”, 8”

or 10”

ISO 30 Degree with Perspective

HDS Bezel

HDS Dust Cover

HDS Mounting

Bracket

HDS Cut-out

Template

HDS Bracket Knobs

HDS

Power/Data Cable

HDS

Connector Caps

HDS

Installation Manual

HDS

Operation Manual

HDS

Quick start guide

HDS

4 x SCREW #10

3/4 PAN HEAD SS

SELFTAP

HDS

4 x SCREW NO.

6X1.5 PANHEAD

PHILLIPS TP1

7

Overview

4

3

2

1

Key Description

1

CURSOR CONTROL: Move the cursor, scroll through menus, adjust

features, view sonar/GPS history. 8 & 10 models also have a y wheel to aid

scrolling.

2

CONTROL KEYS

ZOUT:

Zoom out to see more of the map with less detail

ZIN: Zoom in to see less of the map with more detail.

Pressing ZOUT & ZIN at the same time will activate Man Overboard mode.

ENTER: Finalize menu selections; shortcut key for functions like saving a

waypoint at cursor position.

MENU: Opens Content & Settings menu.

LIGHT/POWER: Controls backlight level & turns the unit on/off.

EXIT: Cancels entries, closes menus & windows; toggles between cursor position

and chart location on Chart page.

PAGES: Press to open Pages menu; press and hold to select the active panel of the

display.

WPT/FIND: Saves a waypoint at current position; accesses searching tools.

3

MMC/SD Card slot: Insert MMC/SD and high-detail mapping cards here.

4

SOFT KEYS: Controls commonly used features and functions. Only available on

8 & 10” units.

8

2

3 4

1

Key Description

1 Sonar (Not available on HDS5M, 7M, 8M or 10M units)

2 Power/Data

3 ENET (Ethernet)

4 NMEA2K (NMEA2000) Network

9

Display Installation

Mounting location

Choose the mounting locations carefully before you drill or cut. The display should be

mounted so that the operator can easily use the controls and clearly see the display screen.

Be sure to leave a direct path for all of the cables. The display screen is high-contrast and anti-

reective, and is viewable in direct sunlight, but for best results install the display out of direct

sunlight. The chosen location should have minimal glare from windows or bright objects.

Ensure that any holes cut are in a safe position and will not weaken the boat’s structure. If in

doubt, consult a qualied marine electronics installer.

The mounting location should be at least 100 mm (4”) away from the compass, at least 300

mm (12”) away from any radio transmitter and at least 1.2 m (4 ft) away from any antenna.

Before cutting a hole in a panel, make sure that there are no hidden electrical wires or other

parts behind the panel.

Do not mount any part where it could be used as a hand hold, where it might be submerged or

where it will interfere with the operation, launching or retrieving of the boat.

If bracket mounting, chose a at area where the display will not be subjected to excessive

vibration.

Leave sufcient clearance space behind the display to connect all relevant cables.

Good ventilation is required behind the mounting panel. Poor ventilation may cause the

display to overheat. The display is designed to operate in temperatures from -15° C to +55° C

(+5° F to +131° F).

For overall width and height requirements, please see the drawings at the back of this manual.

10

Bezel Removal

1: To removing the bezel from the 5 and 7-inch models the card slot door must be open

2: To remove the bezel use a at head screwdriver.

3: Insert screwdriver into the bezel release slots and pry out and away from the unit. The

bottom of the bezel will release from the unit. Push up to release the top bezel catches.

For 8 and 10-inch models

1: While pulling the lower left or right corner of the bezel toward the outside of the unit

2: Push up towards the top of the unit to release the top bezel catches.

Note: All models have four adhesive strips behind the bezel. These strips should be kept free

of dust and other foreign material when the bezel is not attached to the unit.

11

Panel Mount

1: Attach the ush mounting template

to the selected mounting position

using adhesive tape.

2: Drill pilot holes for the four hole saw

cuts and for the four self tapping

screws used to secure the display.

3: Use a hole saw to cut the four corner

radius

4: Cut along the dotted line and remove

the shaded area.

5: Connect all cables to the rear of

the unit before placing the unit

into the console. Secure using the four

provided #6-20 x 1-1/2” screws

6: To nish off the installation rmly

clip the front bezel in place

12

Bracket Mount

An alternative to ush mounting the HDS display is to bracket mount the unit. This method

has the advantage that the display can be easily removed when not in use and may be tilted to

achieve the best possible viewing angle.

1: Loosely screw securing knobs to the

Display unit.

2: Temporarily mount the display unit

in the bracket

3: Make sure the display can be

adjusted to the correct angle without

interfering with the surrounding.

Allow space for cables attached to

the rear of the unit

4: Remove the display unit and use the

mounting bracket as a template to

mark the four positions of the screw

holes and optional center cable hole.

5: Drill a pilot hole for the four screws

and an optional hole large enough

for the cables to emerge from.

6: Secure the bracket to the surface

7: Connect the cables.

13

8: Slide the display into the mounting

bracket and secure in place with the

bracket knobs.

9: Attach the bezel. Firmly clip the

front bezel in place.

14

Transducer Installation

Recommended Tools and Supplies

Tools and Supplies (not included)

If you plan to route the transducer cable through the transom, you will need either a 1” drill

bit or a 5/8” drill bit depending on the size of the transducer cable connector. Each transom

mount requires a high quality, marine grade above- or below-waterline sealant/adhesive

compound. The following installations also call for these recommended tools and supplies.

One-piece Bracket Transom Installation

Tools: two adjustable wrenches or socket wrench, drill, #29 (0.136”) drill bit, screwdriver.

Supplies: none.

Two-piece Bracket Transom Installation

Tools: two adjustable wrenches or socket wrench, drill, #20 (0.161”) drill bit, screwdriver.

Supplies: four, 1” long, #12 stainless steel wood screws.

TMB-S Bracket Trolling Motor Installation

Tools: two adjustable wrenches or socket wrench, screwdriver. Supplies: plastic cable ties.

Skimmer Transducer Shoot-through Hull Installation

Supplies: alcohol wipes, 60 and 160 grit sandpaper, and marine grade above- or below-

waterline epoxy adhesive.

Pod Transducer Shoot-through Hull Installation

Supplies: alcohol wipes, 60 and 160 grit sandpaper, and marine grade above- or below-

waterline epoxy adhesive.

15

Skimmer Installation Instructions

Transducer location and installation is one of the most critical steps in sonar installation.

Select a transducer location

To function properly the Skimmer transducer must be in the water at all times and in a

location that has a smooth ow of water when the boat is moving.

Good location

Poor location

Good location

Note: Aluminum boats with strakes or ribs on the hull can create large amounts of

turbulence at higher speeds. A good transducer location on these types of boats is between the

ribs closest to the engine.

If the transducer is not placed in a smooth ow of water, interference caused by bubbles and

turbulence may show on-screen in the form of random lines or dots. The unit also could lose

bottom signal when the boat is on plane.

Note: When mounting the transducer, make sure it does not interfere with the hauling of the

boat.

Do not mount the transducer

closer than approximately one

foot from the engine’s lower

unit. This will prevent cavitation

interference from the prop.

16

Aligning Ratchets on Transducer bracket

Aligning ratchets on one-piece bracket:

The one-piece bracket assembly includes two black plastic ratchets. The ratchets are used to

align the transducer with the boat hull. Each ratchet has the letters A-E molded into it.

3: Hold the transducer assembly against the

transom. Look at the transducer from the

side.Try to adjust the transducer so its face

is parallel to the ground. If it does, then the

"A" position is correct.

Transom

2: Slide the transducer in the

bracket and temporarily

slide the bolt through the

transducer bracket, as

shown in the image at

right.

1: Insert the ratchets in the bracket with the

letter "A" aligned with the dot stamped on the

outside of the transducer bracket, as shown in

the following series of diagrams.

Ratchet

Bracket

Align dot and

letter "A".

If the transducer will not adjust with its face parallel to the ground, remove the transducer and

ratchets from the bracket. Reinsert the ratchets into the bracket, this time with the letter “B”

aligned with the dot stamped in the bracket.

Reassemble the transducer and bracket and place it against the transom. Again, check to see if

the transducer will adjust so its face is parallel with the ground. Repeat this process until the

transducers face will adjust so that it is parallel with the ground.

17

1: Place two of the ratchets

in each side of the bracket

with the letter "A" aligned with

the alignment mark molded

into each bracket.

Ratchet

Bracket

Alignment mark

4: Hold the transducer assembly

against the transom. Look at

he transducer from the side. Try

to adjust the transducer so its

face is parallel to the ground.

If it does, then the

"A" position is correct.

3: Slide the transducer in the bracket

and temporarily slide the bolt through

the transducer bracket.

Transom

2: Now place the other two

ratchets on the transducer with

the letter "A" aligned in the

12 o'clock position on the

transducer stem.

Aligning ratchets on two-piece bracket

The two-piece bracket includes four black plastic ratchets. The ratchets are

used to align the transducer with the boat hull. Each ratchet has the letters A-F

molded into it.

If the transducer will not adjust with its face parallel to the ground.

5: Remove the transducer and ratchets

from the bracket. Reinsert the ratchets

into the bracket, this time with the

letter “B” aligned with the dot stamped

in the bracket. Reassemble the

transducer and bracket and place it against the transom. Again, check to see if the

transducer will adjust so its face is parallel with the ground. Repeat this process until the

transducers face will adjust so that it is parallel with the ground.

18

Metal washer

Lock nut

Rubber washers

Bolt

Metal washer

Ratchets

Bolt

Small at

washer

Thick rubber

washer

Lock nut

Large at

washer

Assembling the Transducer bracket

After determining the correct position for the ratchets, loosely assemble the transducer and

bracket assembly as shown in one of the two diagrams below.

One-piece bracket assembly

Note:

Do not tighten the transducer bracket assembly until you have aligned the transducer

and bracket on the transom.

Two-piece bracket assembly

Note:

Do not tighten the transducer bracket assembly until you have aligned the transducer

and bracket on the transom.

19

Aligning and Attaching the Transducer

Adjust the transducer so that its "face" is parallel with the ground and its center line is even

with the bottom of the boat hull.

Note: When mounting the transducer to the transom, there are two extremes you should

avoid, rst, do not let the edge of the mounting bracket extend below the bottom of the hull,

left image, above. Second, do not let the bottom of the transducer rise above the bottom of

the hull, right image, above.

The center line of the transducer

should be level with the bottom of

the boat hull and its "face" parallel

with the ground.

Transom

Bottom of hull.

Transducer face

For single frequency

transducers, with a

one-piece bracket,

assemble it with the

cable passing over the

bolt and through the

bracket, as shown here.

Do not over tighten

the transducer bracket

lock nut. If you do,

the transducer may not

"kick-up" if it strikes an

object in the water.

Transducer bracket

mounted too low.

Bottom of hull.Bottom of hull.

Transom Transom

Transducer bracket

mounted too high.

Page is loading ...

Real Cable HDS-12 User manual

Real Cable HDS-12 User manual

Related papers

Other documents