Megasat DVB-T antenna T3 User manual
- Category
- Network antennas
- Type
- User manual
T3
Benutzerhandbuch
• Kompatibel mit allen terrestrischen SD und HD Receivern (DVB-T, ISDB-T, DMB-T/H, ATSC) und DAB/FM Radios.
• Wasserdichtes und UV-beständiges Gehäuse aus spritzgegossenem ASA Material mit super Haltbarkeit.
• Rundstrahlantennen für den Empfang von VHF, UHF und FM Signalen überall in Europa.
• Eingebauter High-Gain und Low Noise Verstärker für minimale Störungen.
• Spezielle Oberflächenbeschichtung für eine perfekte Beständigkeit bei allen Wetterbedingungen.
• Der beste terrestrische Empfang für alle Boote, Caravans und Wohnmobile.
Technische Daten:
Installationsanleitung
Abbildung 1
Außenansicht des Daches Innenansicht des Daches
Lieferumfang:
Frequenzbereich ................... VHF: 47-230 MHz
UHF: 470-862 MHz
Empfangsbereich .................FM / VHF / UHF
Verstärkung .............................. 30 dB
Rauschmaß ...............................3 dB
Ausgangsleistung .................max. 110 dBµV
Widerstand ...............................75 Ohm
Anschluss ...................................F-Stecker
Spannungsversorgung .....DC 5-12 Volt
Antennendurchmesser .....1220 mm
Step 1: Wählen Sie den Standort
Bestimmen sie den Standort der Antenne und der Stromversorgung, anhand des poteniellen Kabelverlaufs. Installieren Sie
bitte unter den folgenden Anweisungen: Wählen Sie einen Ort außerhalb des Daches, der eine einfache Verbindung zur
Spannungsversorgung und zum Anschluss an dem TV ermöglicht. Achten Sie darauf, dass der Untergrund flach ist.
Siehe Abbildung 1.
8
1. Antenne ............................... 1x
2. Gummiring .........................1x
3. Antennenfuß.....................1x
4. Wasserschutzring ...........1x
5. Lochplatte ...........................1x
6. Schraubenset ....................4x
- Sechskantmuttern
- Federbeilagscheibe
- Dichtungsring
7. Schlossschrauben ..........4x
8. Netzteil mit Verstärkungsregler (optional)
- DC 12V Kabel
-12V AC/DC Netzteil
Megasat Werke GmbH
Industriestraße 4a
D-97618 Niederlauer
Model NO.: MV-9011C (with MP-001)
OMNI-DIRECTIONAL MARINE & CARAVAN TV ANTENNA
HDTV
Compatible
ATSC
Com pa ti ble
1
Frequency range:VHF:47-230MHz
UHF:470-862MHz
Receiving range: FM/VHF/UHF
Gain: 30dB
Noise figure: 3dB
Max. output level: 110dBµV
Impedance: 75Ω
Connector: F-connectors
Power supply: DC 12V
1.Antenna x 1
2.Rubber ring x 1
3.Aluminum Mountx 1
4.Water-proof washer x 1
5.Roof Gasket x 1
6.Screw sets x 4
Hexagon Nuts x 4
Spring washer x 4
Antenna Gasket x 4
7. Carriage Bolts x 4
8. Power supply MP-001 kits
Technical Specification
Included in Packaging:
Installation Guide:
STEP 1. Choose Location
Antenna & power supply location determines wher
e and how you run cables, so please install under the following instructions:
Choose a location outside the roof which allow easy connection to power supply and television. Make sure the location is flat and
have sufficient space. See Figure1.
12V AC/DC power adapter
Gain adjuster
Power supply with gain adjuster
DC 12V input wire kits
8
2
{
6
{
6
4
5
3
7
water-proof washer
roof
roof gasket
Figure 1
Outside view of roof Inside view of roof
Specially compatible with HDTV of various digital terrestrial signal
(DVB-T,ISDB-T,DMB-T/H,ATSC) and DAB/FM radios.
The antenna is surface-treated to withstand impacts from saltwater
and weather conditions
Build-in high gain and low noise amplifier, shielded for minimum
interference.
Waterproof housing design made of UV resistant, injection molded
ASA material with super durability.
Omnidirectional antennas receive VHF, UHF, and FM signal from every
point regardless of the direction you are travelling.
The best digital terrestrial TV reception solution for your boating and caravans
SMD Technology and micro-electronics makes the high quality amplifier, ensure the
excellent antenna performance.
Product features
Step 2:
Step 3:
Step 4:
Bohrlöcher
1.) Legen Sie die Lochplatte (# 5) an der gewählten Position aufs Dach und markieren Sie das große Loch und die 4 Schraub-
löcher auf dem Dach. Siehe Abbildung 2.
2.) Entfernen Sie die Lochplatte wieder und bohren Sie die 5 gekennzeichneten Löcher in das Dach.
Installation der Antenne
1). Ziehen Sie das Antennenkabel durch die Halterung (siehe Abbildung 5).
2.) Stecken Sie die Antenne auf die Halterung (siehe Abbildung 6). Drehen Sie dann die Sechskantmuttern in die entgegen-
gesetzte Richtung, um die Antenne zu befestigen (siehe Abbildung 7).
Befestigen Sie die Antenne
1.) Legen Sie die wasserdichte Unterlegscheibe (# 4) entsprechend auf die 4 Schraubenlöcher.
2.) Führen Sie das Antennenkabel durch die mittlere Öffnung des Daches. Siehe Figure 8.
3.) Setzen Sie 4 Schlossschrauben (# 7) durch die Halterung, Scheibe (# 4) und Dach. Siehe Figure 9
4.) Gehen Sie ins Innere des Fahrzeugs / Yacht. Ziehen Sie das Antennenkabel durch das Dachdichtung (# 5) und befestigen
Sie die 4 Schlossschrauben (# 7) mit Schraub-Sets (# 6) entsprechend der Innenseite des Daches. Siehe Abbildung 10.
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
Abbildung 2
Abbildung 5
Abbildung 8
Abbildung 10
Abbildung 3
Abbildung 6
Abbildung 9
Abbildung 4
Abbildung 7
4 Löcher für
Schlossschrauben
1 Loch für
Koaxialkabel
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
Step 5:
Step 6:
Verbindung des Antennenkabels
Verbinden Sie das Antennen Koaxialkabel (weiblicher F-Stecker) mit dem Koaxialkabel (männlicher F-Stecker) des Netzteils.
Siehe Abbildung 11.
Anschließen der Stromversorgung an V1 (optional)
Option 1: Stromversorgung von AC/DC-Netzadapter. Siehe Abbildung 12.
1). Verbinden Sie das Kabel von der Antenne zum Stromversorgungseingang.
2.) Verbinden Sie den Ausgang des Netzteils mit TV-Receiver oder dem Fernsehgerät.
3.) Verbinden Sie den AC/DC-Adapter mit der 12V DC-Buchse am Netzteil und stecken Sie den Adapter in die Steckdose.
4.) Regeln Sie die Verstärkung am Netzteil für besten Signalempfang.
Option 2: Stromversorgung von DC-Batterie. Siehe Abbildung 13.
1). Verbinden Sie das Kabel von der Antenne zum Stromversorgungseingang.
2.) Verbinden Sie den Ausgang des Netzteils mit TV-Empfänger oder TV.
3.) Schließen Sie die DC 12V-Eingang-Drähte an die 12V DC-Buchse des Netzteils.
4.) Verbinden Sie das andere Ende der Drähte „+“ & „-“ an den 12V DC-System des Fahrzeugs / der Yacht.
5.) Regeln Sie die Verstärkung am Netzteil für besten Signalempfang.
Wenn die Antenne und Stromversorgung installiert worden ist und Sie alle Kabel richtig angeschlossen haben, müssen
Sie zuerst einen Sendersuchlauf durchführen, um alle verfügbaren Programme zu empfangen. Führen Sie einen erneuten
Sendersuchlauf durch, sobald die Antenne bewegt wird oder das Signal nicht mehr ausreicht.
Abbildung 11
Abbildung 12
Stromversorgung von
AC/DC Netzteil
Stromversorgung von
der Batterie
Abbildung 13
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Connect the antenna cable
Connect the antenna coaxial cable(Female F connector) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
AC/DC adapter
12V 150mA
Gain
Adapter
power
supply
antenne
TV
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Connect the antenna cable
Connect the antenna coaxial cable(Female F connector) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
DC 12V
Gain
Adapter
power
supply
antenne
TV
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Connect the antenna cable
Connect the antenna coaxial cable(Female F connector) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
T3
user manual
• Specially compatible with HDTV of various digital terrestrial signal (DVB-T, ISDB-T, DMB-T/H, ATSC) and DAB/FM radios.
• The antenna is surface-treated to withstand impacts from saltwater and weather conditions
• Built-in high gain and low noise amplifier, shielded for minimum interference.
• Waterproof housing design made of UV resistant, injection molded ASA material with super durability.
• Omnidirectional antennas receiver VHF. UHF and FM signal from every point regardless of the
direction you are travelling.
• The best digital terrestrial TV reception solution for your boating and caravans
• SMD Technology and micro-electronics makes the high quality amplifier, ensure the excellent
antenna performance.
Specications:
Installation Guide:
Figure 1
Outside view of roof Inside view of roof
Delivery
Frequency range ...................VHF: 47-230 MHz
UHF: 470-862 MHz
Receiving range .....................FM / VHF / UHF
Gain ...............................................30 dB
Noise figure .............................. 3 dB
Max. output level ..................max. 110 dBµV
Impedance ...............................75 Ohm
Connector ................................. F-connector
Power supply ...........................DC 5-12 Volt
Antenna diameter ................1220 mm
Megasat Werke GmbH
Industriestraße 4a
D-97618 Niederlauer
Step 1:
8
1. Antenna ...............................1x
2. Rubber ring ........................1x
3. Aluminium mount.........1x
4. Water-proof washer ......1x
5. Roof gasket ........................ 1x
6. Screw sets ........................... 4x
- Hexagon nuts
- Spring washer
- Antenna gasket
7. Carriage Bolts ....................4x
8. Power supply (optional)
- DC 12V cable
-12V AC/DC power supply
Choose Location
Antenna & power supply location determines where and how you run cables, so please install under the following inst-
ructions: Choose a location outside the roof wich allow easy connaction to power supply and television. Make sure the
location is flat and have sufficent space. See figure 1.
Model NO.: MV-9011C (with MP-001)
OMNI-DIRECTIONAL MARINE & CARAVAN TV ANTENNA
HDTV
Compatible
ATSC
Com pa ti ble
1
Frequency range:VHF:47-230MHz
UHF:470-862MHz
Receiving range: FM/VHF/UHF
Gain: 30dB
Noise figure: 3dB
Max. output level: 110dBµV
Impedance: 75Ω
Connector: F-connectors
Power supply: DC 12V
1.Antenna x 1
2.Rubber ring x 1
3.Aluminum Mountx 1
4.Water-proof washer x 1
5.Roof Gasket x 1
6.Screw sets x 4
Hexagon Nuts x 4
Spring washer x 4
Antenna Gasket x 4
7. Carriage Bolts x 4
8. Power supply MP-001 kits
Technical Specification
Included in Packaging:
Installation Guide:
STEP 1. Choose Location
Antenna & power supply location determines wher
e and how you run cables, so please install under the following instructions:
Choose a location outside the roof which allow easy connection to power supply and television. Make sure the location is flat and
have sufficient space. See Figure1.
12V AC/DC power adapter
Gain adjuster
Power supply with gain adjuster
DC 12V input wire kits
8
2
{
6
{
6
4
5
3
7
water-proof washer
roof
roof gasket
Figure 1
Outside view of roof Inside view of roof
Specially compatible with HDTV of various digital terrestrial signal
(DVB-T,ISDB-T,DMB-T/H,ATSC) and DAB/FM radios.
The antenna is surface-treated to withstand impacts from saltwater
and weather conditions
Build-in high gain and low noise amplifier, shielded for minimum
interference.
Waterproof housing design made of UV resistant, injection molded
ASA material with super durability.
Omnidirectional antennas receive VHF, UHF, and FM signal from every
point regardless of the direction you are travelling.
The best digital terrestrial TV reception solution for your boating and caravans
SMD Technology and micro-electronics makes the high quality amplifier, ensure the
excellent antenna performance.
Product features
Step 2:
Step 3:
Step 4:
Drill holes
1.) Place the roof gasket (#5) in the choosen location and mark 1 center hole and 4 screw holes on the roof. See figure 2.
2.) Remove the roof gasket (#5) and drill the aboved-mentioned 5 holes accordingly on the roof.
Install the antenna
1.) Gently pull the antenna cable through the mount. See figure 5
2.) Slide the antenna onto the mount. See figure 6. Then slide the hexagon nuts in the opposite direction to lock it lighter.
See figure 7
Fix the antenna
1.) Place the water-proof washer (#4) correspond to the 4 screw holes.
2.) Run the antenna cable through the center hole of the roof. See figure 8.
3.) Put 4 carriage bolts (#7) through the mount and washer (#4) and roof. See figure 9.
4.) 4.) Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket (#5) and fix the 4 carriage bolts (#7) with
screw sets (#6) accordingly inside the roof. See figure 10.
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
Figure 2
Figure 5
Figure 8
Figure 10
Figure 3
Figure 6
Figure 9
Figure 4
Figure 7
4 holes for screws
1 hole for
coaxial cable
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
STEP 2. Drill Holes
1)Place the roof gasket(#5) in the chosen location and mark 1 center hole and 4 screw holes on the roof.See Figure2
2)Remove the roof gasket(#5) and drill the aboved-mentioned 5 holes accordingly on the roof
4 holes for screws
Hole for
coaxical cable
STEP 4. Fix the Antenna
1)Place the water-proof washer(#4) correspond to the 4 screw holes.
2)Run antenna cable through the center hole of the roof. See Figure8
3)Put 4 carriage bolts(#7) through the mount and washer(#4) and roof.See Figure9
4)Go inside the vehicle / yacht. Pull the antenna cable through the roof gasket(#5) and fix the 4 carriage bolts (#7) with screw sets(#6)
accordingly inside the roof. See Figure10
Figure 2
Figure 5
Figure 3 Figure 4
Figure 6 Figure 7
Figure 8 Figure 9
Figure 10
STEP 3. Install the Antenna
1)Gently pull the antenna cable through the mount.See Figure 5
2)Slide the antenna onto the mount. See Figure 6.Then slide the hexagon Nuts in the opposite direction to lock it tighter. See Figure 7
Step 5:
Step 6:
Connect the antenna cable
Connect the antenna coaxial cable (Female F-connector) to the coaxial cable (Male F-connector) of power supply unit.
See figure 11.
Connect power supply V1
Option 1: Power from AC/DC power adapter. See figure 12.
1.) Connect the cable from antenna to power supply input.
2.) Connect the output connector of the power supply unit to DTV receivers or TVs.
3.) Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.) Adjust the gain in power supply unit for best signal reception.
Option 2: Power from DC battery. See figure 13.
1.) Connect the cable from antenna to power supply input.
2.) Connect the output connector of the power supply unit to TV-receiver oder TV.
3.) Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.) Connect the other end of the wires „+“ & „-“ to the 12V DC system of vehicle/yacht.
5.) Adjust the gain in power supply unit for best signal reception.
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a
channel scan before watching TV in order to receive maximum programs. Run a channel scan as once the antenna is mo-
ved or the TV loses a channel. Now you can enjoy the TV Programm after you nish running a channel scan.
AC/DC adapter
12V 150mA
DC 12V
Gain
Adapter
Gain
Adapter
power
supply
power
supply
antenna
antenna
TV
TV
Figure 11
Figure 12
powered from
AC/DC power adapter
powered from
DC battery
Figure 13
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Connect the antenna cable
Connect the antenna coaxial cable(Female F connector) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Connect the antenna cable
Connect the antenna coaxial cable(Female F connector) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
Power
supply
TV
AC/DC adapter
12V 150mA
Powered from
AC/DC power adaptor
Gain
adjuster
Power
supply
TV
DC 12V
+ -
Powered from
DC battery
Gain
adjuster
Once the antenna and power supply have been installed and all cables have been properly connected, you must run a channel scan before
watching TV in order to receive maximum programs. Run a channel scan as once the antenna is moved or the TV loses a channel. Now you
can enjoy the TV program after you finish running a channel scan.
STEP 5. Connect the antenna cable
Connect the antenna coaxial cable(Female F connector) to the coaxial cable(Male Fconnector) of power supply unit. See Figure11
Figure 11
Figure 12
Figure 13
STEP 6: Connect power supply MP-001 kits
Option 1: Power from AC/DC power adapter. See Figure 12.
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the AC/DC adapter to the 12V DC jack on the power supply unit, and plug the adapter into the power socket.
4.Adjust the gain in power supply unit for best signal reception
Option 2: Power from DC battery. See Figure 13
1.Connect the cable from Antenna to power supply input.
2.Connect the output connector of the power supply unit to DTV receivers or TVs.
3.Connect the DC 12V input wires to the 12V DC jack on the power supply unit.
4.Connect the other end of the wires "+" & " -" to the 12V DC system of vehicle/yacht.
5.Adjust the gain in power supply unit for best signal reception.
-
1
-
2
-
3
-
4
-
5
-
6
Megasat DVB-T antenna T3 User manual
- Category
- Network antennas
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Megasat DVB-T antenna T1 User manual
-
-
Megasat DVB-T 40 User manual
-
-
-
-
-
Megasat Shipman User Manual and Installation Instructions
-