Amantii BI-50-DEEP Owner's manual

Brand: Amantii

Model: BI-50-DEEP

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

Amantii BI-50-DEEP is a built-in electric fireplace with a 50-inch viewing area. It can be hard-wired or plugged into a standard 120-volt outlet. The BI-50-DEEP comes with a variety of features, including:

Realistic flame effects that can be customized to your liking
Adjustable heat settings to keep you warm and comfortable
A remote control for easy operation
A built-in timer to turn the fireplace on and off automatically
Safety features to protect your home and family

The BI-50-DEEP is a great way to add warmth and ambiance to any room in your home.

Realistic flame effects that can be customized to your liking
Adjustable heat settings to keep you warm and comfortable
A remote control for easy operation
A built-in timer to turn the fireplace on and off automatically
Safety features to protect your home and family

The BI-50-DEEP is a great way to add warmth and ambiance to any room in your home.

INSTALLATION AND OPERATION INSTRUCTIONS FOR BI-DEEP

UNITS

BI-40-DEEP

BI-50-DEEP

BI-60-DEEP

BI-72-DEEP

BI-88-DEEP

SAFETY INFORMATION

WARNING

If the information in these instructions are

not followed exactly, a fire or explosion

may result causing property damage,

personal injury or loss of life.

Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

TABLE OF CONTENTS

Please read and carefully follow all of the instruction found in this manual. Please pay special

attention to the safety instructions provided in this manual. The instructions included here will assure

that you have many years of dependable and enjoyable service from your Amantii product.

IMPORTANT INSTRUCTIONS....................................................................................................................................3

UNPACKING AND TESTING APPLIANCE...............................................................................................................4

GROUNDING APPLIANCE.........................................................................................................................................4

LOCATING THE FIREPLACE.....................................................................................................................................4

BI-40-DEEP...................................................................................................................................................................5

BI-50-DEEP...................................................................................................................................................................6

BI-60-DEEP...................................................................................................................................................................7

BI-72-DEEP...................................................................................................................................................................8

BI-88-DEEP...................................................................................................................................................................9

INSTALLATION..........................................................................................................................................................14

SAFETY DRILL SCREW AREA................................................................................................................................10

FOR BATHROOM USE..............................................................................................................................................12

HARD-WIRE INSTALLATION..................................................................................................................................11

PANORAMA COVER INSTALLATION....................................................................................................................18

MEDIA OPTIONS.......................................................................................................................................................19

OPERATION................................................................................................................................................................20

INSTALLING WALL THERMOSTAT........................................................................................................................22

REPLACEMENT PARTS............................................................................................................................................23

EXPLODED VIEW......................................................................................................................................................24

TROUBLE SHOOTING..............................................................................................................................................25

SERVICE HISTORY....................................................................................................................................................26

WARRANTY...............................................................................................................................................................27

OUTDOOR INSTALLATIONS .........................................................................................................................................13

IMPORTANT INSTRUCTIONS

Read all instructions before installing or using this heater.

2. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at

least 3 feet from the front of the heater; keep them away from sides and rear as well.

3. Always unplug heater when it’s not in use.

4. Do not operate the fireplace if it has a damaged cord or plug, after it has malfunctioned, or if the

unit has been dropped or damaged in any way.

5. Never place the heater where it may fall into a bathtub or other water containers.

6. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners or anything

else. Arrange the cord away from traffic areas where it could not be tripped over.

7. To disconnect the heater, turn the controls to "OFF" before removing the plug from the outlet.

8. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may

cause an electric shock, fire or damage to the heater.

9. To prevent a possible fire, do not block air intakes in any manner.

10. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint

or flammable liquids are used or stored.

11. Use this heater only as described in this manual. Any other use not recommended by the

manufacturer may cause fire, electric shock or injury to persons.

12. Avoid the use of an extension cord because the extension cord may overheat and cause a fire.

13. Always use properly grounded fused and polarized outlets.

14. Always use ground fault protection where it is required by electrical codes.

15. Always disconnect the power before performing any cleaning, maintenance or relocation of the

heater.

16. To prevent a possible fire, do not burn wood or other materials in this heater.

17. To prevent electric shock or fire, always use a certified electrician, should new circuits or

outlets be required.

When transporting or storing the heater, keep it in a dry place, free from excessive vibration.

18.

UNPACKING AND TESTING APPLIANCE

Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the

appliance operates properly by plugging the power supply cord into a conveniently located 120 Volt

grounded outlet.

GROUNDING APPLIANCE

This appliance is for use on 120 Volts. The cord has a plug as shown in (A). An adapter as shown in (C)

is available for connecting three-blade grounding type plugs to two-slot receptacles. The green

grounding lug extending from the adapter must be connected to a permanent ground such as a

properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is

available.

To disconnect appliance, turn controls to off, then remove plug from outlet.

LOCATING THE FIREPLACE

Plan where to locate and frame the fireplace. This will save time and money later when you install

the fireplace. Before installation consider the following:

1. Where the fireplace is located must allow for wall and ceiling clearances (see INSTALLATION)

2. Consider a location where the fireplace screen will not be exposed to direct sunlight from

windows or doors.

3. A 15 ampere, 120 Volt, 60 Hz branch circuit with proper ground must be available at the location.

Preferably a dedicated branch circuit should be provided to avoid circuit breakers to trip of fuses

to blow.

BI-40-DEEP

Description Built-in Appliance

Voltage 120V AC 60Hz

Watts 1500W Max

NO HEATER 25W

MOTOR HEATER 19W

Appliance Width 38 5/8” or 98.1 cm

Appliance Height 23 5/8” or 60 cm

Appliance Depth 12 5/8” or 32.2 cm

Gross Weight 94.6lbs or 43kg

Plug Location Left side

Cord Length 70 7/8” or 180 cm

Rough Wall Opening Size 40”× 25“ or

101.6 cm× 63.5cm

BTU 4800

This appliance has been tested in

accordance with the UL Standard 2021

for fixed and location dedicated

electric room appliances in the United

States and Canada. If you need

assistance during installation, please

contact your local dealer.

NOTE: This appliance must be

electrically wired and grounded in

accordance with local codes. In the

absence of local codes, use the

current CSA C22.1 Canadian Electrical

Code in Canada or the ANSI/NFPA 70

National Electrical Code in the United

States.

BI-50-DEEP

Model Number BI-50-DEEP

Voltage 120V AC 60Hz

Watts 1500W Max

NO HEATER 25W

MOTOR HEATER 19W

Appliance Width 48 5/8” or 123.5 cm

Appliance Height 23 5/8” or 60 cm

Appliance Depth 12 5/8” or 32.2 cm

Gross Weight 110lbs or 50kg

Plug Location Left side

Cord Length 70 7/8” or 180 cm

Rough Wall Opening Size 50”× 25“ or

127 cm ×63.5cm

BTU 4800

This appliance has been tested in

accordance with the UL Standard 2021

for fixed and location dedicated electric

room appliances in the United States and

Canada. If you need assistance during

installation, please contact your local

dealer.

NOTE: This appliance must be

electrically wired and grounded in

accordance with local codes. In the

absence of local codes, use the current

CSA C22.1 Canadian Electrical Code in

Canada or the ANSI/NFPA 70 National

Electrical Code in the United States.

BI-60-DEEP

Description Built-in Appliance

Voltage 120V AC 60Hz

Watts 1500W Max

NO HEATER 25W

MOTOR HEATER 19W

Appliance Width 58 5/8” or 148.5 cm

Appliance Height 23 5/8” or 60 cm

Appliance Depth 12 5/8” or 32.2 cm

Gross Weight 127.6lbs or 58kg

Plug Location Left side

Cord Length 70 7/8” or 180 cm

Rough Wall Opening Size 60”× 25“ or

152.4 cm× 63.5 cm

BTU 4800

This appliance has been tested in

accordance with the UL Standard 2021

for fixed and location dedicated electric

room appliances in the United States and

Canada. If you need assistance during

installation, please contact your local

dealer.

NOTE: This appliance must be

electrically wired and grounded in

accordance with local codes. In the

absence of local codes, use the current

CSA C22.1 Canadian Electrical Code in

Canada or the ANSI/NFPA 70 National

Electrical Code in the United States.

BI-72-DEEP

Description Built-in Appliance

Voltage 120V AC 60Hz

Watts 1500W Max

NO HEATER 25W

MOTOR HEATER 19W

Appliance Width 72 1/8” or 183.2 cm

Appliance Height 23 5/8” or 60 cm

Appliance Depth 12 5/8” or 32.2 cm

Gross Weight 156.2lbs or 71kg

Plug Location Left side

Cord Length 70 7/8” or 180 cm

Rough Wall Opening Size 73 1/2”× 25“ or

186.7 cm× 63.5 cm

BTU 4800

This appliance has been tested in

accordance with the UL Standard 2021

for fixed and location dedicated electric

room appliances in the United States and

Canada. If you need assistance during

installation, please contact your local

dealer.

NOTE: This appliance must be

electrically wired and grounded in

accordance with local codes. In the

absence of local codes, use the current

CSA C22.1 Canadian Electrical Code in

Canada or the ANSI/NFPA 70 National

Electrical Code in the United States.

BI-88-DEEP

Description Built-in Appliance

Voltage 120V AC 60Hz

Watts 1500W Max

NO HEATER 25W

MOTOR HEATER 19W

Appliance Width 88 5/8” or 225.2 cm

Appliance Height 23 5/8” or 60 cm

Appliance Depth 12 5/8” or 32.2 cm

Gross Weight 195.8lbs or 89kg

Plug Location Left side

Cord Length 70 7/8” or 180 cm

Rough Wall Opening Size 89 1/4”× 25“ or

226.7 cm× 63.5 cm

BTU 4800

This appliance has been tested in

accordance with the UL Standard 2021

for fixed and location dedicated electric

room appliances in the United States and

Canada. If you need assistance during

installation, please contact your local

dealer.

NOTE: This appliance must be

electrically wired and grounded in

accordance with local codes. In the

absence of local codes, use the current

CSA C22.1 Canadian Electrical Code in

Canada or the ANSI/NFPA 70 National

Electrical Code in the United States.

SAFETY DRILL SCREW AREA

There is a safety drill screw area as show below.

Please make sure that the fix screws are in this area.

Themanualcontrolpadposition

Safety drill screw area

(Dark area)

HARD- WIRE INSTALLATION

Turn off the appliance completely and let cool before servicing. Only a qualified service person

should service and repair this electric appliance.

If it is necessary to hard wire this appliance, a qualified electrician must remove the cord connection,

and wire the appliance directly to the household wiring.

This appliance must be electrically connected and grounded in accordance with local codes, if hard

wired. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in

Canada or the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

1. Remove the cover plate from the left side of the appliance by removing the two screws, as

shown below. Unscrew and remove power cord.

2. Attach the wiring to the junction block. Please make sure the live wire goes into the “L”, the

neutral wire into “N” and the ground wire into “G”.

3. Put the plate back and screw back.

FOR BATHROOM USE

If this unit is installed in a bathroom it must be protected by a GIF receptacle or circuit. If receptacle is

used it must be readily accessible.

To prevent electric shock, please be aware that this unit is an electrical appliance that is NOT watertight

and must be installed as to prevent water from entering unit. This must be installed away from shows,

tubs, etc. Never locate fireplace where it may fall into a bathtub or other water container.

All wiring connections to line power shall be in accordance with local building code requirements.

Inquires about local codes and regulations must be done prior to installation.

The overhang (A) must extend at least 1/2 the roof-line height (B).

Height is measured from the base of the ﬁreplace.

For example: if the roof-line (B) is 8’ above the base of the ﬁreplace,

the overhang (A) must be at least 4’.

OUTDOOR INSTALLATIONS

The BI-DEEP series electric fireplaces are suitable for installation in outdoor areas protected from direct

water impingement. In addition to maintaining the listed mantel and combustibles clearances, a rain

protection overhang factor of 1/2 shall be constructed to the front and to each side of the installed

appliance. See illustration below. All wiring connections to line power shall be in accordance with local

building code requirements. Inquires about local codes and regulations must be done prior to

installation.

When installed in outdoor applications, it is recommended that the BI-DEEP models use the protective

PAN-COVER.





INSTALLATION

The BI-DEEP models are designed to be built-in and allow for the finishing material (drywall, stone,

tile, etc) to be built right down to the glass edge. However, that application is not always desirable or

available so the surround could be used as an alternate finish option.

Note: The optional trim can be pulled out directly from the unit. It will need two people to do it.

The rough wall opening size of the fireplace:

W(＂) D(＂) H(＂)

BI-40-DEEP 40 12 25

BI-50-DEEP 50 12 25

BI-60-DEEP 60 12 25

BI-72-DEEP 73 1/2 12 25

BI-88-DEEP 89 1/4 12 25

1. Take out the unit from the box. Please do the pre-test before you install the fireplace. Pull

out the optional trim from the unit as shows below.

optional trim

2. Remove the framing plates from the unit

framing plate

3. Re-fix the framing plates to the unit as the picture shows

framing plate

4. Bend up the framing plates.

5. Put the unit into the opening.

6. Drive the mounting screws into the framing plates on the unit and the wall studs.

7. After checking that the fireplace operates properly, cover the glass panel with

protective plastic bag and install plywood or drywall.

Fireplace

framing plate

NOTE: In order to use the supplied trim kit, the thickness of the desired wall finish

can not exceed 1 inch.

8. Decorate the plywood or drywall with glazed tile, wallpaper, etc.

Fireplace

9. Put back the trim that you’ve removed from the unit at STEP 1.

trim

PANORAMA COVER INSTALLATION

Make sure install the pan-cover when the fireplace used outdoors.

Remove the cover from the packaging.

The handles will need to be attached to the

cover with the provided hardware as shown in

fig. 1

First, place a plate washer and then a spring

washer on the screw as shown in fig. 2

Affix the handles to the front of the cover using

the prepared screws. Fig. 3

Insert the assembled cover onto the unit as

shown in Figs. 4 and 5

Fig 1

Fig 2

Fig 3

Fig 4

Fig 5

Media Options

The BI-40-DEEP, BI-50-DEEP,BI-60-DEEP

is shipped with 3 large glass nuggets, clear

and blue diamond shaped media and 11

piece log set.

The BI-72-DEEP, BI-88-DEEP is shipped

with 6 large glass nuggets, clear and blue

diamond shaped

media

and

piece

log

set.

Fire Glass Media-Log Installation

1. Take off the front clear glass. There is a

bracket which hold the front glass.It is

show as below. Unscrew the screw and

take off the bracket. Turn around and

insert to the gap. It can hook the glass

and pull out the glass.

2. Installing the fire glass media. Pour the

fire glass media into the tray as shown

below. Feel free to use any combination

of fire glass media that you find most

appealing

3.Put back the front glass and screw back

the bracket.

11 piece log set

OPERATION

The fireplace can be operated either by the switches located on the left bottom of the fireplace unit

or by supplied remote control.

Plug the fireplace into a 15 Amp wall socket.

MANUAL OPERATION

1. The main power ON/OFF switch in position O, the fireplace is OFF.

2. When main power ON/OFF switch is at position I, the fireplace is ready to use.

3. Press the button repeatedly to set the heater to desired heat setting. The heater indicator

LED will glow which shows the current heater settings.

a) RED 1500W HEAT OUTPUT

b) BLUE 750W HEAT OUTPUT

c) PURPLE AUTO MODE

AUTO MODE

Under this mode the heater will automatically turn ON at high heat setting 1500W heat output when

the room temperature drops below 22℃(72℉ ). When the room temperature is between

22-25℃(72-77℉ ) the heater output will switch to low heat setting 750W. When the room

temperature goes above 25℃(77℉) the heater will be turned off and the cycle will continue. The

LED indicator will be PURPLE in colour under this mode.

4. Flame effect: Press the button marked to adjust the flame brightness. The flame brightness

will cycle through –Low-Medium-High -OFF.

5. Mood light effect: Press the button marked to change the mood light colour.

NOTE: If operated at the Low heat setting, the fireplace will not provide as much heat output as in

the High heat setting, however the low setting will not require as much electrical power to operate.

To avoid overloading a circuit, do not plug the fireplace into a circuit that already has other

appliances working. When the fireplace is not in use switch off and unplug.

SAFETY CUT-OFF

l This appliance is fitted with a safety cut-off which will operate if the fireplace overheats (eg. Due

to blocked air vents). For safety reasons, the fireplace will NOT automatically reset.

l To reset the appliance, disconnect the appliance from the main supply for at least 10 minutes.

Reconnect the supply to the main and switch on the appliance.

Page is loading ...

Amantii BI-50-DEEP Owner's manual

Brand: Amantii

Model: BI-50-DEEP

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

Realistic flame effects that can be customized to your liking
Adjustable heat settings to keep you warm and comfortable
A remote control for easy operation
A built-in timer to turn the fireplace on and off automatically
Safety features to protect your home and family

The BI-50-DEEP is a great way to add warmth and ambiance to any room in your home.

Download PDF

report

Amantii BI-50-DEEP Owner's manual

This manual is also suitable for

Amantii BI-50-DEEP Owner's manual

Related papers

Other documents