Miele W 2819 i WPM L Operating instructions

Operating instructions

for Washing machine

W 2819i

To avoid the risk of accidents or

damage to the machine it is

essential to read these instructions

before it is installed and used for the

first time. M.-Nr. 07 739 960

en-GB

Disposal of the packing

material

The transport and protective packing

has been selected from materials which

are environmentally friendly for disposal

and should be recycled.

Ensure that any plastic wrappings,

bags etc. are disposed of safely and

kept out of the reach of babies and

young children. Danger of suffocation!

Disposal of your old machine

Electrical and electronic machines

often contain materials which, if

handled or disposed of incorrectly,

could be potentially hazardous to

human health and to the environment.

They are, however, essential for the

correct functioning of your machine.

Please do not therefore dispose of it

with your household waste.

Please dispose of it at your local

community waste collection / recycling

centre or contact your Dealer for

advice. Ensure that it presents no

danger to children while being stored

for disposal.

Caring for our environment

2

Caring for our environment .........................................2

Warning and Safety instructions .....................................6

Operating the washing machine.....................................10

Control panel .....................................................10

Before using for the first time.......................................12

Washing environmentally and economically ..........................13

Energy and water consumption ....................................13

Detergent .....................................................13

How to wash correctly.............................................14

Extra quiet.....................................................16

Spinning ........................................................19

Final spin speed ..................................................19

Delay start.......................................................20

Programme chart .................................................21

Extras ..........................................................24

Garment care label symbols ........................................25

Programme sequence .............................................26

Changing the programme sequence .................................28

Cancelling a programme ............................................28

Interrupting a programme ...........................................28

Changing a programme ............................................28

Adding or removing laundry after a programme has started ................29

Safety lock .......................................................29

Detergent .......................................................30

The correct detergent ..............................................30

Water softener ....................................................32

Washing with several components ....................................32

Fabric conditioners and liquid starch ..................................33

Automatic dispensing of fabric conditioner or liquid starch to laundry

at the end of a programme ........................................33

Adding fabric conditioner or starch separately ........................33

Colour run and dye removers/dyes ....................................33

Contents

3

Cleaning and care ................................................34

External casing and fascia panel .....................................34

Extra cleaning ..................................................34

Cleaning the detergent dispenser drawer...............................34

Cleaning the filter in the water inlet ....................................36

Problem solving guide ............................................37

The programme does not start .......................................37

Fault messages in the display ........................................38

General problems .................................................39

An unsatisfactory wash result ........................................40

The drum door does not open when you press the Door button..............41

Opening the drum door in the event of a blocked drain outlet

and/or power failure................................................42

After sales service ................................................45

Future updates (PC) .............................................45

Appliance guarantee ............................................45

Optional spare parts and accessories ...............................45

Installation and connection ........................................46

Front view........................................................46

Rear view ........................................................47

Installation surface.................................................48

Installing the washing machine ....................................48

Removing the transit fittings .........................................48

Re-fitting the transit bars ............................................50

Levelling the machine ..............................................51

Screwing out and adjusting the feet .................................51

Washer-dryer stack..............................................51

Building under a continous worktop / in a kitchen run .....................52

Matching the fascia panel to the height of adjacent drawer fronts ............53

Spacer bars ...................................................53

Removing the spacer bars ........................................53

Fitting the front panel ...............................................54

Front panel dimensions ..........................................54

Fitting the front panel ............................................54

Contents

4

Fitting a door front panel made by another manufacturer...................55

Preparing the front panel .........................................55

Preparing the fixing points ........................................56

Fitting a plinth facing ...............................................57

The Miele water protection system ....................................58

Connection to the water supply .......................................59

Connection to the drainage system....................................60

Electrical connection U.K. ...........................................61

Consumption data ................................................62

Notes for test institutes: ..........................................62

Technical data ...................................................63

Programmable functions...........................................64

To access programmable functions .................................64

To select a programmable function .................................64

To alter a programmable function ..................................64

To come out of programmable functions .............................64

Language

! ......................................................64

Water plus .......................................................65

Gentle action .....................................................65

Suds cooling .....................................................65

Code ...........................................................66

Temperature unit ..................................................67

Buzzer ..........................................................67

Keypad tone .....................................................67

Brightness .......................................................67

Contrast .........................................................67

Standby display ...................................................68

Memory .........................................................68

Anti-crease.......................................................68

Optional accessories..............................................69

CareCollection ....................................................69

Contents

5

This washing machine conforms to

current safety requirements.

Inappropriate use can, however,

lead to personal injury and damage

to property.

To avoid the risk of accidents and

damage to the washing machine,

please read these instructions

carefully before using it for the first

time. They contain important

information on its installation, safety,

use and maintenance.

Keep these instructions in a safe

place and ensure that new users are

familiar with the content. Pass them

on to any future owner.

Correct application

~

This washing machine is not

designed for commercial use. It is

intended for use in domestic

households and in similar working and

residential environments such as:

–

Shops

–

Offices and showrooms

and by residents in establishments

such as

–

Hostels and guest houses

~

It must only be used as a domestic

appliance to wash items which are

specified by the manufacturer as being

washable on the care label.

Any other usage is not supported by

the manufacturer and could be

dangerous. Miele cannot be held liable

for damage resulting from incorrect or

improper use or operation of the

washing machine.

~

This washing machine is not

intended for use by persons (including

children) with reduced physical,

sensory or mental capabilities, or lack

of experience and knowledge, unless

they are supervised whilst using it or

have been shown how to use it by a

person responsible for their safety.

Safety with children

~

Keep children away from the

washing machine at all times. It is not a

toy! To avoid the risk of injury do not

allow children to play on or near it or to

play with its controls. Supervise

children whilst you are using it.

~

Older children may only use the

washing machine if its operation has

been clearly explained to them and

they are able to use it safely,

recognising the dangers of misuse.

Warning and Safety instructions

6

Technical safety

~

Before setting up the washing

machine, check it for any externally

visible damage.

Do not install or use a damaged

washing machine.

~

Before connecting the washing

machine, ensure that the connection

data on the data plate (voltage and

connected load) match the mains

electricity supply. If in any doubt,

consult a qualified electrician.

~

The electrical safety of this washing

machine can only be guaranteed when

continuity is complete between it and

an effective earthing system which

complies with current local and national

safety regulations. It is most important

that this basic safety requirement is

present and regularly tested, and

where there is any doubt the household

wiring system should be inspected by a

qualified electrician. The manufacturer

cannot be held liable for the

consequences of an inadequate

earthing system (e.g. electric shock).

~

Do not connect the washing

machine to the mains electricity supply

by an extension lead. Extension leads

do not guarantee the required safety of

the appliance (e.g. danger of

overheating).

~

Faulty components must only be

replaced by genuine Miele original

spare parts. Only when these parts are

fitted can the safety standards of the

machine be guaranteed.

~

Unauthorised repairs could result in

unforeseen dangers for the user, for

which Miele cannot accept liability.

Repairs should only be undertaken by a

Miele approved service technician.

Ensure current is not supplied to the

machine until after maintenance or

repair work has been carried out.

~

If the connection cable is faulty it

must only be replaced by a Miele

approved service technician to protect

the user from danger.

~

In the event of a fault or for cleaning

purposes, the washing machine is only

completely isolated from the electricity

supply when:

– it is switched off at the wall socket

and the plug is withdrawn, or

– it is switched off at the mains, or

– the mains fuse is withdrawn, or the

screw-out fuse is removed (in

countries where this is applicable).

~

This washing machine must only be

connected to the on-site water supply

using a new hose kit. Old hoses must

not be re-used.

~

In countries where there are areas

which may be subject to infestation by

cockroaches or other vermin, pay

particular attention to keeping the

machine and its surroundings in a

clean condition at all times. Any

damage which may be caused by

cockroaches or other vermin will not be

covered by the guarantee.

Warning and Safety instructions

7

~

This washing machine may only be

used in mobile installations such as

ships if a risk assessment of the

installation has been carried out by a

suitably qualified engineer.

~

Do not make any alterations to the

washing machine, unless authorised to

do so by Miele.

Correct use

~

Do not install your washing machine

in rooms where temperatures below

freezing may occur. Frozen hoses may

burst or split. The reliability of the

electronic control unit may be impaired

at temperatures below freezing point.

~

Before using the washing machine

for the first time, check that the transit

bars at the rear of the machine have

been removed (see section on

"Installation and connection"). During

spinning, a transit bar which is still in

place may result in damage to both the

machine and adjacent furniture or

appliances.

~

Turn off the stopcock if the machine

is to be left for any length of time (e.g.

holiday), especially if there is no floor

drain (gully) in the immediate vicinity.

~

Flooding danger.

If hooking the drain hose into a wash

basin, check that the water can drain

off quickly enough to prevent the sink

from overflowing. Make sure the drain

hose is secure, so that the force of the

water flowing out of the hose does not

dislodge it.

~

Take care to ensure that foreign

objects (e.g. nails, pins, coins, paper

clips) do not find their way into the

machine with the laundry. These may

damage components of the machine

(e.g. suds container, drum), which in

turn can result in damage to the

laundry.

~

If the correct amount of detergent is

dispensed, the machine should not

need to be descaled. If, however, you

do wish to descale the machine only

use proprietary non-corrosive descaling

agents and strictly observe the

instructions on the packaging. A

special descaling agent is available to

order from the Miele Spare Parts

Department or via the internet on

www.miele-shop.com.

Warning and Safety instructions

8

~

Textiles which have been

pre-treated with solvent based cleaning

agents must be thoroughly rinsed in

clean water before being washed in the

machine.

~

Never use solvent based cleaning

agents, e.g. those containing benzene,

in this machine, as this may result in

damage to component parts and create

toxic fumes. Such agents also pose a

fire and explosion hazard.

~

Never use solvent based cleaning

agents, e.g. those containing benzene,

to clean the outside surfaces of this

machine. They can cause damage to

plastic surfaces.

~

Only use dyes specified by the

manufacturer as being suitable for use

in a domestic washing machine. Always

observe the manufacturer's instructions

carefully.

~

Colour run and dye removers

contain sulphur compounds which can

cause damage such as corrosion. Do

not use these products in this machine.

~

If detergent comes into contact with

the eyes, rinse them thoroughly with

lukewarm water immediately. If

swallowed, seek medical assistance

immediately and retain the packaging

or label for reference. Those with skin

problems or sensitive skin should avoid

their skin coming into contact with

detergent.

~

Only remove laundry from the

washing machine once the drum has

stopped turning. Reaching into a

moving drum is extremely dangerous

and could result in injury.

Accessories

~

Accessory parts may only be fitted

when expressly approved by Miele. If

other parts are used, guarantee,

performance and product liability

claims will be invalidated.

Miele cannot be held liable for

damage caused by non-compliance

with these Warning and Safety

instructions.

Warning and Safety instructions

9

Control panel

a Extra option buttons

Various extra options can be added

to the washing programmes.

b Display

See the following page for more

information.

c Delay start button

For delaying the start time of a

programme.

d Temperature button

For selecting a temperature.

e Spin speed button

For selecting the final spin speed or

e (Rinse hold) or No . (Without

spin).

f PC / Optical interface

This is used by service technicians

to run diagnostic checks on your

machine and can also be used to

update programming data in the

future.

g Start/Stop button

For starting the programme selected

and cancelling a programme once it

has started.

h Programme selector

For selecting a programme. The

indicator light next to the selected

programme will come on. The

programme selector can be turned

clockwise or anti-clockwise.

i K button

For switching the washing machine

on and off.

To save energy, the washing

machine will switch itself off

automatically 15 minutes after the

end of the programme/anti-crease

phase or after being switched on if

no other selection is made.

j Door button

Opens the machine door.

Operating the washing machine

10

The following are selected via the

display:

– wash temperature

– spin speed

– delay start

– cancellation of a programme

– safety lock

– programmable functions

The display also shows:

–

the programme duration

–

the programme sequence

Programme duration

After the start of a programme, the

estimated programme duration will

appear in the display in hours and

minutes.

When delay start is being used, the

programme duration will appear after

the delay start time has elapsed.

During the first 8 minutes the washing

machine measures how much water is

being absorbed by the laundry and

uses this to calculate the load. The

programme duration may be longer or

shorter depending on this absorbency

rate.

Delay start

The delay start time selected will

appear in the display.

After the Start/Stop button has been

pressed, the delay start time will start

counting down. If the delay start time is

more than 10 hours, it will count down

by the hour. If it is less than 9 hours and

59 minutes it will count down minute by

minute.

Once the delay start time has elapsed,

the programme begins and the

estimated programme duration shows

in the display.

Programmable functions

The programmable functions can be

used to tailor washing programmes to

suit your individual requirements. In

programming mode, the display will

show the function selected.

Operating the washing machine

11

Before using the machine for the first

time ensure that it is correctly

installed and connected. See

"Installation and connection". Also

check that the drain filter is securely

tightened to prevent the risk of water

leaks during use.

This washing machine has

undergone a thorough functional test

in the factory and there will be some

residual water in the drum from this

process.

For safety reasons, spinning is not

possible until the machine has been

prepared for using for the first time. To

activate the spinning function you must

run a wash programme without laundry

and without detergent.

Using detergent could result in an

excessive build-up of foam.

This also activates the ball valve. The

ball valve prevents detergent escaping

from the suds container into the sump

during a wash programme, thus making

maximum use of the detergent.

^

Press the K button in.

If the washing machine is being

switched on for the first time, the

welcome screen will appear.

The welcome screen will appear in

the display every time the machine is

switched on until a programme

lasting longer than 1 hour has been

completed.

Setting the language

You will be asked to select the

language you require for the display. It

is possible to change the language at

any time via the programmable

functions.

! deutsch

^

If the language shown is not the one

you want, select the language you do

want by turning the programme

selector. Confirm your selection by

pressing the Start/Stop button.

Reminder to remove transit bars

To avoid the risk of damage, the

transit bars must be removed before

the machine is used for the first time.

See "Installation and connection" for

instructions on how to do this.

^ After removing the transit bars (if this

has not already been done by your

fitter), press the Start/Stop button.

Running your first programme

Run the Cottons 60°C programme

without any laundry and without

detergent.

^

Open the stopcock.

^

Press the Start/Stop button.

^

At the end of the programme switch

the machine off.

The machine is now ready for use.

Before using for the first time

12

Energy and water consumption

–

Water consumption and energy

usage are determined by the size of

the load.

To make the most out of your

machine, load the maximum dry load

for the programme you are using.

–

Use the Automatic plus and

Express 20 programmes for small

loads.

–

When smaller amounts of laundry are

washed the automatic load

recognition system will reduce the

amount of water, time and energy

used. This may mean that the time

left shown in the display is adjusted

during the course of the wash

programme.

– Using the Cottons 60°C programme

instead of the Cottons 95°C

programme will give energy savings

of between 35% and 45%. This is

sufficient for most levels of soiling.

Detergent

–

Do not exceed the amounts of

detergent recommended by the

manufacturer on the packaging.

–

Adjust the dosage to the degree of

soiling of the laundry.

–

Reduce the amount of detergent with

smaller loads (approx.

1

/

3

less than

the amount recommended can be

used when washing a half load).

Choosing the correct extra option

(Short, Pre-wash and Pre-wash +

soak)

Select:

– A wash programme together with the

Short extra option for light to normal

soiling where there are no obvious

marks.

– A wash programme without any extra

options for normal to heavy soiling

with visible staining.

–

A wash programme together with the

Pre-wash + Soak extra option for

very heavily soiled laundry

.

–

The Pre-wash extra option for laundry

with large amounts of dirt (e.g. dust,

sand).

When drying with a tumble dryer

Selecting the highest possible spin

speed for the wash programme will

save energy when drying in a tumble

dryer afterwards.

Washing environmentally and economically

13

Brief instructions

The headings numbered A, B, C,...

show the operating sequence and can

be used as brief instructions.

A Sort the laundry

^ Empty all pockets.

,

Foreign objects (e.g. nails,

coins, paper clips, etc.) can cause

damage to garments and

components in the machine.

^

Badly soiled areas, stains etc. should

be cleaned as soon as possible,

preferably whilst still fresh. Spillages

should be carefully dabbed off using

a soft colourfast cloth. Do not rub!

Badly soiled areas can be pre-treated

with liquid detergent, stain removers

etc. first, following the manufacturer's

instructions. With particularly stubborn

stains ask your dry cleaner for advice.

,

If you use a solvent-based clean

-

ing agent (e.g. one containing ben

-

zene) to pre-treat a stain, make sure

that any plastic parts (e.g. buttons)

are protected, and that the cleaning

agent is rinsed off before washing the

garment in the machine.

,

Do not use solvent-based

cleaning agents in or on this machine.

^

Sort the laundry by colour and by

care label. Most garments have a

textile care label in the collar or side

seam.

Dark textiles often contain excess dye

and should be washed separately

several times before being included in

a mixed load. Always wash whites and

coloureds separately.

– Curtains: Remove lead weights first

or place in a laundry bag.

–

Underwiring and collar stiffeners:

Any loose wiring in bras, shirt collar

stiffeners, etc. should be removed or

sewn in.

–

Knitted garments, trousers and

jeans, T-shirts and sweat shirts: Turn

inside out, if recommended by the

manufacturer.

–

Close any zips, fasten hooks and

eyes etc before washing.

–

Fasten duvet covers etc. to prevent

small items from being rolled up

inside them.

Do not wash any items in this machine

which are specified by the

manufacturer as not washable on the

care label. (h symbol)

How to wash correctly

14

B Switch on the washing machine

C Load the drum

^

Press the Door button to open the

drum door.

^

Unfold the laundry and load loosely

into the drum. Mixing both large and

small items gives better wash results

and also helps distribute the load

evenly during spinning.

The most efficient use of energy and

water is achieved when a full load is

washed. However, do not overload as

this causes creases and reduces

cleaning efficiency.

Make sure that no items are caught

between the drum door and seal.

^

Shut the door with a gentle swing.

D Select a programme

^

Turn the programme selector

clockwise or anti-clockwise to the

required programme. The

programme indicator light for the

programme selected will come on.

E Select a temperature / spin speed

The suggested temperature and/or spin

speed can be changed.

1:49 60° 1400

^

Press the Temperature button to alter

the temperature and press the Spin

speed button to alter the spin speed.

How to wash correctly

15

F Select an extra option(s)

^ Select an extra option by pressing

the appropriate button. The relevant

indicator light will come on to show

which extra option has been

selected.

Not all the extra options are suitable for

use with every programme.

You can only select extra options which

are compatible with the programme

being used.

Short

For light to normal soiling with no visible

staining.

The duration of the main wash is

reduced.

Water plus

The water level in the main wash and

the rinses will be increased if the Water

plus option is selected.

However, you can select other settings

for Water plus. These are described in

"Programmable functions".

Pre-wash

+

The Pre-wash

+

button is used for

activating the Pre-wash option on its

own as well as a Pre-wash with an

additonal soak time of one or two hours.

Press the button:

x 1 = Pre-wash

x 2 = Pre-wash+1hsoak

x 3 = Pre-wash +2 h soak

x 4 = No options selected

Extra quiet

If using your washing machine during

quiet periods, you can reduce the noise

levels even more.

The machine will activate the Rinse

hold (e) option and not spin if the

Extra quiet option is selected. The

programme duration is longer.

To deactivate Rinse hold

^

Use the Spin speed button to select

the spin speed you want.

By using Delay start you can make

sure the final spin occurs outside

quiet periods in the home.

How to wash correctly

16

G Select Delay start (if required)

The start of a programme can be

delayed from 30 minutes up to 24

hours, allowing you to make use of

night-time economy electricity rates, for

example.

See "Delay start" for more information.

H Add detergent

It is important to dispense the correct

amount, because... . .

. . . too little detergent results in:

–

Laundry not getting properly clean

and with time it may become grey

and hard to the touch.

– Greasy particles clinging to the

laundry.

– Limescale deposits on the heater

elements.

. . . too much detergent results in:

– Excessive foam which causes a low

level of agitation and poor wash,

rinse and spin results.

–

Higher water consumption (an

additional rinse cycle will

automatically switch in).

–

A burden to the environment.

^

Pull out the detergent drawer and

add detergent to the compartments

as follows:

i

Detergent for the pre-wash (divide

the total recommended amount as

follows: add

1

/

3

to compartment i

and

2

/

3

to compartment j)

j

Detergent for the main wash,

including Soak if selected

§

Fabric conditioner or liquid starch

^

Close the detergent drawer.

See "Detergent" for further information.

How to wash correctly

17

I Start the programme

^

Press the flashing Start/Stop button.

If a delay start time has been selected,

then this will count down in the display.

At the end of the delay start time or im

-

mediately after the programme has

started (if no delay start time has been

selected) the estimated programme

duration will appear in the display.

During the first 8 minutes the machine

measures how much water is being

absorbed by the laundry. The

programme duration may be longer or

shorter depending on this absorbency

rate.

The programme sequence is also

shown in the display. The washing

machine shows you when each section

of the programme is reached.

J Remove the laundry when the

programme has finished

In the anti-crease phase after the

programme has finished, the following

will appear alternately in the display:

0:00 Anti-crease

and

0:00 Finish

^

Press the Door button to open the

drum door.

The washing machine will switch off

automatically 15 minutes after the

end of the anti-crease phase. You will

need to press the K button to switch

it back on again.

^

Remove the laundry.

Check that all items have been

removed from the drum. Items left in

the drum could discolour other items

in the next wash or become

discoloured themselves.

^ Check the folds in the door seal for

any small articles, e.g. buttons, which

might be lodged there.

^ Switch the machine off with the

K button.

^

Close the drum door. Otherwise there

is the danger of objects being placed

inadvertently in the drum. If these

remained unnoticed and were

washed in the next load, they could

damage the laundry.

How to wash correctly

18

Final spin speed

You can reduce the final spin speed.

However, you cannot select a final spin

speed higher than that shown in the

chart above.

Rinse and interim spin

There is a spin after the main wash and

between the rinses. A reduction in the

final spin speed will also reduce the

interim spin speed. If a spin speed of

less than 700 rpm is selected for a

Cottons programme, an additional rinse

is introduced.

To omit the final spin (Rinse hold)

^

Select the Rinse hold (e) setting

using the Spin speed button. The

laundry will not be spun and will

remain suspended in the final rinse

water. This reduces creasing if the

laundry is not going to be removed

from the drum immediately after the

end of the programme.

–

To start the final spin

:

The washing machine will display the

maximum spin speed possible. You

can select a spin speed lower than

this. Start the final spin by pressing

the Start/Stop button.

– To end the programme

:

Press the Door button. The water will

drain away. Press the Door button

again to open the door.

To omit rinse and interim spin and

the final spin (No .)

^

Select the No . setting using the

Spin speed button.

The laundry is not spun after the final

rinse. The water will drain away and the

machine will go straight into the

anti-crease stage.

With some programmes an additional

rinse is introduced if this setting is

selected.

Spinning

19

Programme rpm

Cottons 1400

Minimum iron 1200

Delicates 600

Woollens / 1200

Proofing 1000

Express 20 1400

Dark garments / Denim 1200

Shirts 600

Intensive plus 1400

Spin 1400

Separate rinse/Starch 1200

Automatic plus 1200

Delay start allows you to choose when

you want the programme to start. The

start of a programme can be delayed

from 30 minutes up to a maximum of 24

hours, allowing you to make use of

night-time economy electricity rates, for

example.

Selecting delay start

^

Press the Delay start button. The

following will appear in the display:

0:30 , 60° 1400

^

Each press on the Delay start button

increases the delay start time:

– in 30 minute steps up to 10 hours,

– in 1 hour steps from 10 hours

upwards.

If you keep the Delay start button

pressed in, the time will continue to

count up to 24 hours.

Activating delay start

^

Press the Start/Stop button to activate

delay start. The following will appear

in the display:

4:30 , until start

After the delay start time has elapsed,

the washing programme will start and

the estimated programme duration and

the programme sequence will show in

the display.

Altering delay start

You can change the delay start time at

any time by pressing the Delay start

button.

Cancelling delay start before delay

start has been activated

^

Press the Delay start button until

24 h appears in the display. Then

press the Delay start button again

briefly to cancel delay start.

If you cancel delay start after the delay

start time has started counting down,

the washing programme will start imme-

diately.

Delay start

20

Page is loading ...

Miele W 2819 i WPM L Operating instructions

This manual is also suitable for

Miele W 2819 i WPM L Operating instructions

Related papers

Other documents