2. American Standard
  3. Afwall Elongated Toilet Flush Valve Toilet 2257.103

American Standard Afwall Elongated Toilet Flush Valve Toilet 2257.103 User manual

  • Hello! I am an AI chatbot trained to assist you with the American Standard Afwall Elongated Toilet Flush Valve Toilet 2257.103 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
M77
© 2008 AS America Inc.
Revised 11/08
AFWALL™ ELONGATED
FLUSH VALVE TOILET
VITREOUS CHINA
AFWALL™ ELONGATED TOILET
• Flush valve toilet
• Vitreous china
• Low-consumption (6.0 Lpf/1.6 gpf)
• Wall-mounted elongated bowl
• Fully glazed trapway
• Direct-fed siphon jet action
• 1-1/2" inlet spud
• Fully-glazed 2-1/8" trapway
• 10" x 12" water surface area
• 100% factory ush tested
❏ 2257.103 Elongated bowl only, top spud
Component Parts:
❏ 047007-0070A Inlet Spud (furnished with bowl)
Nominal Dimensions:
635 x 375 x 381mm
(25" x 14-3/4" x 15")
Recommended working pressure – between
30 psi at valve when ushing and 80 psi static
Fixture only, less seat, bolt caps, and ush valve
Compliance Certications -
Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixtures
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE
BUILDING FACILITIES - CHECK LOCAL CODES.
When installed so top of seat is 432 to 483mm (17" to 19") from the
finished floor.
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
BARRIER FREE
To Be Specied:
❏ Color: ❏ White
❏ Seat: 5901.100 American Standard Seat
❏ 5901.110 American Standard Seat with EverClean
®
❏ Alternate Seat: 5905.100 Heavy Duty
American Standard Seat
❏ 5905.110 Heavy Duty American Standard Seat
with EverClean
❏ Flush Valve:
❏ American Standard Selectronic
™
#6065.161.002
DC Power (Top Spud)
❏ Carrier Fitting (by others):
M78
© 2008 AS America Inc.
AFWALL™ ELONGATED
FLUSH VALVE TOILET
VITREOUS CHINA
NOTES:
● Toilet designed to meet ADA handicapped standards with seat height set at 432 to
483mm (17" to 19") from nished oor.
WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-FELT (WAX RING
NOT RECOMMENDED).
SUGGESTED 2mm (1/16) CLEARANCE BETWEEN FACE OF WALL AND BACK OF BOWL.
TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM BREAKER ON
THE FLUSH VALVE, THE PLUMBER MUST VERIFY DIMENSIONS SHOWN FOR SUPPLY
ROUGHING.
FLUSH VALVE NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.
CARRIER FITTING AS REQUIRED TO BE FURNISHED BY OTHERS.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORT.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of
tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is assumed for
use of superseded or voided pages
FINISHED WALL
470mm
(18-1/2)
C/L OF SEAT POST
HOLES 140 mm
(5-1/2) CENTER
635mm
(25)
73mm
(2-7/8)
133mm
(5-1/4)
191mm
(7-1/2)
292mm
(11-1/2)
(4) 22mm
(7/8)
HOLES
375mm
(14-3/4)
C/L OF
OUTLET
121mm
(4-3/4)
FINISHED
FLOOR
32mm
(1-1/4)
381mm
(15)
1" N.P.T. OR C.W.T. SUPPLY
AS REQUIRED TO FLUSH VALVE
330mm
(13)
19mm
(3/4)
133mm
(5-1/4)
95mm
(3-3/4)
70mm
(2-3/4)
1-1/2 SPUD
C/L
229mm
(9)
2257
Revised 11/08
BARRIER FREE
/