Sony CMA-D3 User manual

Type
User manual

This manual is also suitable for

2 (GB)
English
Owner’s Record
The model and serial numbers are located at the bottom.
Record these numbers in the spaces provided below.
Refer to these numbers whenever you call upon your Sony
dealer regarding this product.
Model No. Serial No.
For the customers in the U.S.A.
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct
the interference at his own expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with the
limits for digital device pursuant to Subpart B of Part 15 of
FCC Rules.
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
For the customers in Europe
This product with the CE marking complies with both the
EMC Directive (89/336/EEC) and the Low Voltage Directive
(73/23/EEC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the
following European standards:
• EN60065: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment(s):
E1 (residential), E2 (commercial and light industrial), E3
(urban outdoors) and E4 (controlled EMC environment, ex.
TV studio)
3 (GB)
GB
Table of Contents
English
Overview
The CMA-D3/D3CE camera adaptor is designed to operate
the Sony DXC-390/390P 3CCD color video camera on an
AC or DC power supply.
As the camera adaptor can be connected to the video camera
using the CCMC-3MZ camera cable and a CCZ-A series
camera cable extendable up to 100 m, the video camera can
be installed a considerable distance from a control room.
About this manual
This manual applies to both the CMA-D3 and CMA-D3CE.
The CMA-D3 is designed for the NTSC color system and
can be connected to a DXC-390 video camera. The CMA-
D3CE is for the PAL color system and can be connected to a
DXC-390P video camera. The operating instructions for
both camera adaptors are the same.
Precautions..........................................................................4
Safty Precautions ...........................................................4
Handling Precautions.....................................................4
Location and Functions of Parts .......................................6
Front Panel.....................................................................6
Rear Panel ......................................................................7
Connections .......................................................................10
Outline .........................................................................10
Basic System Configuration for the DXC-390/390P...11
Connecting to a Computer ...........................................12
Specifications.....................................................................13
4 (GB)
Precautions
Safety Precautions
Power supply
The unit is designed for operation on a power supply
meeting the requirements indicated in the “Specifications”
on page 13 (GB).
Do not drop or place heavy objects on the power cord. If
the power cord is damaged, turn off the power
immediately. It is dangerous to use the unit with a
damaged power cord.
Disconnect the power cord from the AC outlet by grasping
the plug, not by pulling the cord.
Do not touch the AC power plug with a wet hand.
Keep foreign objects out of the cabinet
Dropping flammable or metal objects into the cabinet, or
spilling liquids nearby can lead to accidents.
In case of malfunctions
If you notice any unusual sound or smell, or smoke, turn off
the power immediately, disconnect the power supply and
contact your Sony dealer.
Handling Precautions
Location
Do not store or use the unit under any of the following
conditions.
In excessive heat or cold
In direct sunlight or near a heater
In damp or dusty locations
In locations subject to vibrations
Near strong magnetic fields
Near a television or radio station generating strong radio
frequency energy
Protect from impact
Do not drop the unit or subject it to severe shocks.
Do not place the unit on an unstable base.
Use of the DC power supply
Use a DC power supply capable of supplying constant
voltage of 30 W or more.
As the power switch of this unit does not operate on DC,
install the power switch and fuse on the DC power source
for safety.
5 (GB)
When connecting the DC power cable to the DC 15 V IN
connector, take special care with the following:
– use a DC power cable of a sufficient current capacity.
– align the polarities correctly.
– make sure that there is no loose connection or short-
circuit on the conductors.
Ventilation
To prevent internal heat buildup, do not block air circulation
around the unit.
Transportation
When transporting the unit, repack it as originally packed at
the factory or in materials equal in quality.
Cleaning
Clean the cabinet and panels by wiping with a soft, dry
cloth. For severe stains, moisten the cloth with a small
amount of neutral solvent, and finish by wiping with a dry
cloth. Do not use alcohol, benzine, thinner or volatile
liquids, as these may discolor or damage the cabinet surface.
6 (GB)
POWER
ON
OFF
CABLE COMP
REMOTE
100m
75
25
50
0
CAMERA ADAPTOR CMA-D3
Note
The POWER switch does not operate when the DC/AC
SELECT switch is set to DC.
3 CABLE COMP (cable compensation) selector
Set the selector to the appropriate position according to the
connected cable length.
4 REMOTE (remote control) connector (mini DIN, 8-
pin)
Connect to the RM-C950 remote control unit (not supplied).
4 REMOTE connector
Location and Functions of Parts
3 CABLE COMP selector
1 Power indicator
2 POWER switch
1 Power indicator
For AC operation, the indicator lights when you set the
POWER switch 2 to ON.
For DC operation, it lights when you supply power to the
DC 15V IN connector on the rear panel.
2 POWER switch
For AC operation, set the switch to ON to turn on the power
of the unit.
Front Panel
This illustration shows
the CMA-D3 model.
7 (GB)
W.E OUT
TRIG IN HD
G/Y OUT B/C
OUT
R/VBS
OUT
CAMERA
DC/AC
SELECT
~
AC IN
DC15V
IN
VD/SYNC
IN
RGB
VBS/Y/C
OUT
1 RGB, VBS/Y/C switch
8 CAMERA connector
9 DC/AC SELECT switch
q; AC IN connector
qa DC 15 V IN connector
1 RGB, VBS/Y/C switch
Set the switch to RGB to output the sync signal from the G/
Y OUT, B/C OUT and R/VBS OUT connectors 2.
Set the switch to VBS/Y/C to output the VBS or Y/C signal
from these connectors.
2 G/Y OUT, B/C OUT and R/VBS OUT (video signal
output) connectors (BNC type)
Output the video signal (RGB or Y/C/VBS) supplied from
the video camera.
Rear Panel
2 G/Y OUT, B/C OUT and R/VBS OUT connectors
3 W.E OUT connector
7 IN/OUT selector
5 HD connector
4 TRIG IN connector
6 VD/SYNC connector
8 (GB)
Location and Functions of Parts
3 W.E OUT (Write Enable pulse output) connector
(BNC type)
Outputs the WE pulse to communicate the timing to store
the image on an external frame memory, etc.
For detailed information, read the instruction manual of the
DXC-390/390P.
4 TRIG IN (trigger input) connector (BNC type)
Connects to a commercially available slave unit in strobe
mode by converting the connector of the slave unit into
BNC type.
For detailed information, read the instruction manual of the
DXC-390/390P.
5 HD (horizontal deflection) input/output connector
(BNC type)
Inputs or outputs the HD signal. Input or output can be
selected by setting the IN/OUT selector 7.
6 VD/SYNC (vertical deflection/sync) input/output
connector (BNC type)
Inputs or outputs the vertical deflection signal or sync
signal. Input or output can be selected by setting the IN/
OUT selector 7.
The type of sync signal is set on the SYSTEM menu of the
video camera.
7 IN/OUT (sync input/output) selector
Set to IN to use the HD connector 5 and VD/SYNC
connector 6 as inputs, and to OUT to use them as outputs.
Set to OUT when external sync is not used.
Using the HD and VD/SYNC connectors
The following shows how to use the HD and VD/SYNC
connectors combined with the menu setting on the video
camera and the IN/OUT selector on this unit.
Purpose
To use HD and
VD signals for
external sync
To use VBS
signal for
external sync
To use HD and
VD signals
output from the
camera
To use SYNC
signal output
from the
camera
Function of connector
HD
HD signal
input
No signal
input
HD signal
output
No signal
output
VD/SYNC
VD signal
input
VBS signal
input
VD signal
output
SYNC
signal
output
Menu
setting on
camera
Any
Any
Set SIGNAL
to HD/VD.
Set SIGNAL
to C. SYNC.
IN/OUT
selector
setting
IN
IN
OUT
OUT
9 (GB)
Pin No. Signal
A Power output
B GND
1 Trigger output
2 GND
3 GND
4 G/Y input
5 R/VBS input
6 GND
7 B/C input
8 GND
9—
10
11
Pin No. Signal
12 WE pulse input
13 Control
14
15
16 GND
17
18 HD input/output
19 GND
20
21 VD/SYNC input/output
22
23
24
9 DC/AC SELECT switch
Set to the right position (AC IN) to operate the video camera
on the AC power supply connected to the AC IN connector.
Set to the left position (DC 15V IN) to operate the video
camera on the DC power supply connected to the DC 15V
IN connector.
q; AC IN connector
Connect to an AC outlet using the AC power cord
(supplied).
qa DC 15V IN connector
Connect to the DC power supply.
8 CAMERA connector (26-pin)
Connect to the DXC-390/390P video camera using the
CCMC-3MZ camera cable. To extend the cable, use the
CCMC-3MZ and CCZ-A series camera cables.
Pin assignment
A
B
1
6
23
12
18
24
11
17
22
7
10 (GB)
Cable length
10 m or less
Approx. 25 m
Approx. 50 m
Approx. 75 m
Approx. 100 m
Connections
Outline
Applicable cameras
You can connect the following Sony video camera to the
unit.
3CCD color video camera DXC-390/390P
Usable camera cables
The following camera cables can be used to connect the unit
to a video camera.
CCMC-3MZ (12-pin, D-sub 9-pin, mini DIN 8-pin and
BNC y 26-pin) (CCZZ-1E cable adaptor supplied)
CCZ-A2/A5/A10/A25/A50/A100 (26-pin y 26-pin)
Set the CABLE COMP selector on the front panel to the
appropriate position according to the camera cable length.
Notes
If your cable length is not indicated in the table, set the
selector to the position for a closer length. Do not use a
cable of more than 100 m.
For DC operation, the usable cable length is limited by the
supplied voltage. If you use the camera cable of 50 m or
longer, connect a 11.5 to 15 V DC power supply.
Power supply
The unit operates on either AC or DC power supply.
AC power
Connect the AC power cord (supplied) to an AC outlet and
set the DC/AC SELECT switch on the rear panel to AC IN
(right position). You can turn on and off the unit with the
POWER switch on the front panel.
DC power
Connect a DC external power source to the DC 15V IN
connector and set the DC/AC SELECT switch on the rear
panel to DC 15V IN (left position).
The power indicator lights when power is supplied to the
DC 15V IN connector. (The POWER switch on this unit
does not operate.)
Selector setting
0
25
50
75
100
CABLE COMP
100m
75
25
50
0
11 (GB)
W.E OUT
TRIG IN HD
G/Y OUT B/C
OUT
R/VBS
OUT
CAMERA
DC/AC
SELECT
~
AC IN
DC15V
IN
VD/SYNC
IN
RGB
VBS/Y/C
OUT
VIDEO OUT
DC IN/VBS
REMOTE
LENS
TRIG IN
MENU LOCK
OFF ON
RGB/SYNC
Basic System Configuration for the DXC-390/390P
Note
Turn off the power to all the units before making any connections.
* To extend the cable, connect the CCMC-3MZ camera cable to the CCZ-A camera cable using the cable adaptor supplied with the CCMC-3MZ.
DXC-390/390P
TRIG IN
REMOTE
RGB/SYNC
CCMC-3MZ camera cable
26-pin
DC IN/VBS
CCZZ-1E cable adaptor*
(supplied with the CCMC-3MZ)
CCZ-A camera cable*
(max. 100 m)
CAMERA
(26-pin)
RM-C950 remote control unit
CAMERA
R/VBS
OUT
Video input
connector
75-ohm coaxial
cable
CMA-D3/D3CE camera adaptor
Video monitor,
VCR, etc.
Power
cord
26-pin
REMOTE (front)
Connecting cable
(supplied with the RM-C950)
12 (GB)
W.E OUT
TRIG IN HD
G/Y OUT B/C
OUT
R/VBS
OUT
CAMERA
DC/AC
SELECT
~
AC IN
DC15V
IN
VD/SYNC
IN
RGB
VBS/Y/C
OUT
VIDEO OUT
DC IN/VBS
REMOTE
LENS
TRIG IN
MENU LOCK
OFF ON
RGB/SYNC
Connecting to a Computer
The following is a connection for controlling the camera with a computer using an RS-232C command.
For details on RS-232C protocols and cables for connection to a computer, contact your authorized Sony dealer.
Connections
1) Use the shielded connecting cable for connecting to a computer.
2) To extend the cable, connect the CCMC-3MZ camera cable to the CCZ-A camera cable using the cable adaptor supplied with the CCMC-3MZ.
DXC-390/390P
TRIG IN
REMOTE
RGB/SYNC
CCMC-3MZ camera cable
26-pin
DC IN/VBS
CCZZ-1E cable adaptor
2)
(supplied with the CCMC-3MZ)
CCZ-A camera cable
2)
(max. 100 m)
CAMERA
(26-pin)
Video input
connector
75-ohm coaxial
cable
CMA-D3/D3CE camera adaptor
Video monitor,
VCR, etc.
Power
cord
26-pin
Computer
Serial interface connector
Connecting cable
1)
R/VBS
OUT
REMOTE (front)
7 (ES)
W.E OUT
TRIG IN HD
G/Y OUT B/C
OUT
R/VBS
OUT
CAMERA
DC/AC
SELECT
~
AC IN
DC15V
IN
VD/SYNC
IN
RGB
VBS/Y/C
OUT
8 Conector CAMERA
9 Interruptor DC/AC SELECT
q; Conector AC IN
qa Conector DC 15 V IN
2 Conectores G/Y OUT, B/C OUT y R/VBS OUT
(salida de señales de vídeo) (tipo BNC)
Envían la señal de vídeo (RGB o Y/C/VBS) suministrada
desde la cámara de vídeo.
Panel posterior
2 Conectores G/Y OUT, B/C OUT y R/VBS OUT
3 Conector W.E OUT
7 Selector IN/OUT
5 Conector HD
4 Conector TRIG IN
6 Conector VD/SYNC
1 Interruptor RGB, VBS/Y/C
1 Interruptor RGB, VBS/Y/C
Ajuste el interruptor en RGB para enviar la señal de
sincronización desde los conectores G/Y OUT, B/C OUT y
R/VBS OUT 2.
Ajuste el interruptor en VBS/Y/C para enviar la señal VBS o
Y/C desde estos conectores.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Sony CMA-D3 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI