Leg
1/32" (1 mm)
Cut Line
"B" Mark
B
B
Top Track
x2
#8-18 x 1-1/2"
Screw Cover
Screw Cover
x2
3
2
1
Notch
Rails
Long Leg
Outside of
the Shower
Wall Jamb – Top View
x2
Hanger
Bracket
x2
Gasket
Tin Snips
9/64"
Number 2 Pencil
Miter Box
32 Teeth Per Inch Blade
Masking Tape
100% Silicone Sealant
Rubber Mallet
5/16" Masonry Bit for Tile
5/16"
1218520**
Hardware Skin Pack
1219162
End Cap
Screw
1048208-C
Wall Jamb*
Gasket
1213732
Barrel Nut
1050048-A
#8-32 x 3/8"
8-32 x 1/4"
Screw
1051142-A
Roller
1050047
Hanger Bracket
1219763-01**
Sex Bolt
1077763-A
Left Door
Panel*
Wall Jamb*
Serial Number Label
1077762
Anchor
1218971
Bumper
1031943**
Screw Cover
1214505-01**
Top Track
1056868-A
Screw
1218476**
Center Guide
#8-18 x 1-1/2"
1213333-01**
Bottom Track
1219930-01**
Handle
Right Door
Panel*
Wipe
Seal*
1219002
Spacer
1216764-01**
Post
1216847**
Back Plate
Handle Skin Pack
1219473**
1219005-A
Screw
Bottom Wall
Jamb Notch
Bottom Wall
Jamb Notch
A
A
"A" Mark
Cut Line
1/4" (6 mm)
Measure distance “A.” Subtract 1/4” (6 mm) or
the width of a number 2 pencil from “A” and cut
the bottom track.
Position the bottom track on the center of the
ledge. If needed, file the ends to match the
corners.
Center the bottom track on the ledge with the leg
to the outside. Tape the bottom track in place and
mark the position.
Important! The bottom track and wall jamb
must sit flat against the shower ledge and the
wall. If needed, trim and file the wall jamb. Use a
coin to match and to transfer the corner radius of
the shower to the wall jamb.
Position the wall jambs over the bottom track.
The long leg of each wall jamb faces the outside
of the shower. Plumb both wall jambs. Mark the
screw holes.
Remove the wall jambs. Drill 5/16” holes into the
walls and insert the anchors.
Reposition both wall jambs. Secure the wall
jambs with screws.
Measure distance “B” above the wall jambs.
Subtract 1/32” (1 mm) or the width of a saw
blade from “B.” Mark and cut the top track.
Place the top track over the wall jambs (either
side may face out). At each end of the top track,
insert and twist a bumper into place over the
rails. Slide the bumpers against the wall jambs.
For both doors, slide a gasket over the top of the
glass panel and into each mounting hole. Press
the hanger bracket over the gasket and align the
hanger brackets with the mounting holes.
5400 Heavy Glass Series Sliding Shower Doors
IMPORTANT! Do not cut the top track the same length as the bottom track.
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for application and
curing time.
Watch this installation online; visit the product page at
www.sterlingplumbing.com.
Sliding Shower DoorsSliding Bath Doors
11218556-2-B
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310
1218556-2-B
Installation and Care Instructions
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Required Tools Parts Identifi cation
2 3 4
7 86 9
1 5
10
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
NOTICE: Do not touch the edges of the tempered glass with tools or any
other hard objects. Do not set the unframed tempered glass directly on the
floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
SterlingPlumbing.com
No Gap
at Top
Sex Bolt
Hanger
Bracket
Barrel
Nut
8-32 x 1/4"
x2
Label
Handle Holes
Showerhead
Label Side
Roller
Screw
Label
x2
#8-32 x 3/8"
Handle
Holes
x2
Label
Side
#8-32 x 3/8"
Label
Screw
Rollers
Handle Holes
Lower the glass.
Raise the glass.
Bottom Track
Lip
Leg
Center of the
Bottom Track
Frame
Guide
Guide
Bottom Track
Wipe Seal
Wall Jamb
Top Track
Self-Tapping
Screws
End Caps
Spacers
Back
Plate
Screw
Outside Panel Inside Panel
Post
9/64"
Frame
Wipe
Seal
Notch
Door
Opening
1/2" (13 mm)
Inside of Shower
Troubleshooting
Symptom: Alignment Recommended Action
1. The top of the door panel is tilted away from
the wall.
A. Remove the door panel from the top track and lower the roller that is closest to the wall. See step 18.
2. The bottom of the door panel is tilted away
from the wall.
A. Remove the door panel from the top track and raise the roller that is closest to the wall. See step 18.
3. The door panel does not touch the bumper. A. Determine whether the door panel top or bottom is closer to the wall, and then adjust the roller closest to the wall.
4. The bottom track is miscut or skewed. A. The notched wall jamb fits over the bottom track to cover any miscut or skewed cuts. Seal as directed to ensure
proper watertight seal. See step 23.
Symptom: Water Leaks Recommended Action
1. Water leaks between panels. A. When showering, make sure the inside panel is against the showerhead wall.
2. Water leaks between the wall jamb and the
door panel.
A. Adjust the door panel to line up with the wall jamb. Add the optional seal. See step 24 and 25.
3. Water leaks under the bottom track. A. Check for proper silicone sealant application. See steps 22 and 23. Apply more silicone sealant in the leak location.
Symptom: Operation (open/close) Recommended Action
1. The inside and/or outside panel is difficult to
move.
A. Ensure a gap exists between the guide and the door panel. If no gap exists, lower the rollers.
B. Ensure the inside center guide is properly secured with the self-tapping screws. See step 19.
C. Ensure the rollers are properly installed. See steps 13, 14, 15, and 16.
D. Clean any debris in the top track groove.
E. Ensure that the hanger bracket is tight to the glass.
While pressing downward on the hanger
brackets, use screwdrivers to thread the sex bolt
into the barrel nut. Tighten until the hanger
brackets are secured firmly in place.
Before proceeding, identify which door panel
will install on the inside track. The inside panel
will be the door panel closest to the showerhead.
When the inside panel is in position, the label
will be on the outside of the shower and the
handle hole will be next to the wall jamb.
On the inside panel, assemble a roller to the
middle hole of each hanger bracket. Install
the rollers on the side of the door panel that is
opposite the label.
Lift the inside panel onto the inside track. The
label faces the outside of the shower.
On the outside panel, assemble a roller to the
middle hole of each hanger bracket. Install the
rollers on the same side of the door panel as the
label.
Lift the outside panel onto the outside track. The
label faces the outside of the shower.
Measure and mark the center of the bottom track.
Position the guide under the lip of the bottom
track. Center the guide on the bottom track and
slide a leg of the guide inside the frame of each
door panel.
While holding the guide in place, slide the doors
from wall to wall. If either panel binds or needs
adjustment, remove the door and position the
rollers in new holes to raise or lower the glass.
Hold the guide in place and secure with the two
self-tapping screws. Do not overtighten!
Insert the endcaps into the bottom corners of
each shower door.
Press a spacer onto each back plate and post. Use
a 9/64” hex wrench to assemble the handles as
shown. On the outside panel, the handle installs
on the outside of the shower. On the inside panel,
the handle installs on the inside of the shower.
Outside the shower, use silicone sealant to seal
along the entire length of the wall jambs and the
bottom track.
Inside the shower, use silicone sealant to seal
along the entire length of the wall jambs and
where the wall jambs meet the bottom track.
Optional Wipe Seal for Water Containment:
Measure the height of the door opening and
add 1/2” (13 mm). Trim both wipe seals to this
measurement. To avoid interference with the
frame of the door panel, notch the bottom of
each wipe seal.
The wipe seal should rest on the top edge of
the bottom track and extend into the top track.
Remove the adhesive backing and attach to the
wall jamb as shown.
21218556-2-B ©2014 Kohler Co.
11 12
17
22
13
18
23
16
21
14
19
24
15
20
25
WARRANTY
5 YEARS LIMITED
SP2375 Series, 5100 Series, 5300 Series, 5400 Series, 6300 Series, 6500 Series
3 YEARS LIMITED
1500 Series, 1900 Series, 2200 Series, 4600 Series, 4700 Series, 4800 Series, 4900 Series, 5900 Series
1 YEAR LIMITED
500 Series, 600 Series, 660 Series, 670 Series, 690 Series, 950 Series, 2300 Series, 3100 Series
Based on the classification specified above, STERLING bath and shower doors are warranted to be free of
manufacturing defects within the time of the specified model’s limited warranty from date of sale.
Kohler Co. will, at its election, repair, rectify or replace a fixture when inspection by Kohler Co. discloses any such
defects occurring in normal usage within the time period of coverage stated above. Kohler Co. is not responsible
for removal or installation costs where replacement is indicated. Damages due to improper handling, installation or
maintenance are not considered manufacturing defects and are not covered by this warranty. This warranty is valid
for the original, consumer purchaser only.
To obtain warranty service, contact Sterling, either through your plumbing contractor, home center, wholesaler
or dealer, or by calling or writing Sterling, Consumer Services, 444 Highland Drive, Kohler, Wisconsin 53044,
1-800-783-7546.
TO THE EXTENT PERMITTED BY LAW, ALL IMPLIED WARRANTIES INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
KOHLER CO. AND SELLER HEREBY DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty
lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and
exclusions may not apply to you. This warranty gives you specific legal rights. You may have other rights which
vary from state/province to state/province.
This is the exclusive written warranty for Kohler Co.
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
Sterling 547808-59S-G05 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Sterling 542808-59S-G03 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Sterling Plumbing Finesse™ Peak® Installation guide
-
Kohler K-702208-L-SHP Installation guide
-
-
-
Sterling Plumbing SP5400 User manual
-
-
-
-
-