Minka Group 841-91 User manual

Type
User manual

Minka Group 841-91 is a lighting fixture designed for indoor use. It features a simple and elegant design that can complement a variety of décor styles. The fixture is easy to install and can be mounted on a wall or ceiling. It comes with all the necessary hardware for installation, including screws, wire connectors, and a mounting bracket. The fixture uses standard light bulbs, which are not included. The maximum wattage for the fixture is 60 watts. The fixture is made of high-quality materials and is backed by a one-year warranty.

Here are some of the benefits of using the Minka Group 841-91 lighting fixture:

Minka Group 841-91 is a lighting fixture designed for indoor use. It features a simple and elegant design that can complement a variety of décor styles. The fixture is easy to install and can be mounted on a wall or ceiling. It comes with all the necessary hardware for installation, including screws, wire connectors, and a mounting bracket. The fixture uses standard light bulbs, which are not included. The maximum wattage for the fixture is 60 watts. The fixture is made of high-quality materials and is backed by a one-year warranty.

Here are some of the benefits of using the Minka Group 841-91 lighting fixture:

INSTALLATION INSTRUCTIONS
Item #841 Rev. 02/27/2012
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
Fig. 2
MOUNTING THE BACKPLATE (Fig.1)
1. Shut off the power at the circuit breaker and
remove old fixture, including the mounting
hardware.
2. Carefully unpack your new fixture and lay out all
the parts on a clear area. Take care not to lose
any small parts necessary for installation.
3. Attach the Crossbar (A) to the junction box using
two Junction Box Screws (B) (Size: #8-32N*L0.5”).
The side of the Crossbar marked GND” must
face out.
4. Thread the Nipple (C) part way into the center
hole of the Crossbar (A).
CONNECTING THE WIRES (Fig. 2)
5. Connect the electrical wires as shown in (Fig.2),
use wire connectors to secure the connections. If
you outlet has a ground wired (green or bare
copper) connect fixture’s ground wire to it.
Otherwise connect fixture’s ground wire directly to
the crossbar using the green screw provided.
MOUNTING FIXTURE AND SHADE (Fig.1)
6. After the wires are connected, carefully tuck them
inside the junction box as you place the Fixture
Body (D) over the Nipple (C). Secure the Fixture
Body (D) against the wall using Knurled Cap (E).
7. Place the Glass Shade (F) into the Fixture Body
(D).
8. Install light bulbs in accordance with fixture
specifications, (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!) (NE PAS
DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
Your installation is now complete. Return power
to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
LA-1396E
E
C
B
A
D
F
MIN 90 SUPPLY CONDUCTORS
Set# A-016
- Crossbar
- Ground screw
- Mounting Screw*2
  • Page 1 1

Minka Group 841-91 User manual

Type
User manual

Minka Group 841-91 is a lighting fixture designed for indoor use. It features a simple and elegant design that can complement a variety of décor styles. The fixture is easy to install and can be mounted on a wall or ceiling. It comes with all the necessary hardware for installation, including screws, wire connectors, and a mounting bracket. The fixture uses standard light bulbs, which are not included. The maximum wattage for the fixture is 60 watts. The fixture is made of high-quality materials and is backed by a one-year warranty.

Here are some of the benefits of using the Minka Group 841-91 lighting fixture:

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI