AO-DPF7LB / AO-DPF8LB USER MANUAL
1
QUICK START GUIDE
Please read carefully before use
AO-DPF7LB / AO-DPF8LB USER MANUAL
2
TABLE OF CONTENTS
Important Safety Instructions and Precautions .................................................................................. 2
Whats in the box ............................................................................................................................... 2
OPERATION ....................................................................................................................................... 3
By Touch Buttons........................................................................................................................... 3
By Remote Control ........................................................................................................................ 3
First time use ................................................................................................................................. 4
Basic settings ................................................................................................................................. 4
Advanced settings ......................................................................................................................... 4
Specifications .................................................................................................................................... 5
IMPORTANT SAFETY INSTRUCTIONS AND PRECAUTIONS
- Read all instructions carefully before use.
- Retain this manual for future reference.
- Use this product only in the manner described.
- Only use a water-dampened soft-cloth to clean the surface of this product.
- The following will damage this product: any liquid such as water or moisture, extreme
heat; cold; humidity, dusty or sandy environments.
- Only place this device on stable surfaces and ensure that any attached cables are secure
and will not cause the device to fall.
- There are no user serviceable parts in this product.
- Un-authorized attempts to dismantle or repair this product will void product warranty and
may result in dangerous electric shock.
- Remove any power or data cords by pulling them from the plug and not the cord.
WHATS IN THE BOX
1
.
Picture Frame
2
.
User Manual
3
.
Power Adaptor
4
.
Remote Control
AO-DPF7LB / AO-DPF8LB USER MANUAL
3
PRODUCT CONNECTIONS AND USE
OPERATION
By Touch Buttons
1 Power on/off
2 Setup (from menu screen)
3 Play / Pause
4 Previous image
5 Next image
6 Back (to enter menu mode)
7 Power indicator light
By Remote Control
AO-DPF7LB / AO-DPF8LB USER MANUAL
4
On/Off Power Pause &
Up Left
Confirm the Selection Right
Down Set Up
Enter Menu or Back
First time use
1) Connect the device to mains power as described above
2) Insert you storage card (eg. SD, USB) with preloaded JPG format images
3) Power the device ON. The device will then boot to the welcome page (LASER logo) then proceed
directly to the slide show presentation from your memory or flash device.
Basic settings
1) During the slide show presentation, press the SETUP key to select between ROTATE and
MAGNIFY (Zoom). If the ZOOM setting is selected, pressing the play button once will magnify
the image by one increment. (Note: after pressing once, wait for the changes to take affect,
before pressing it again, otherwise the unit may freeze) By then selecting the SAVE PICTURE
option you can then (permanently) save these changes to the file. Selecting EXIT will then
take you back to the slide show presentation.
2) During a slide show presentation, press the BACK button. The screen will then display your
images in THUMB NAIL format. The NEXT and PREVIOUS buttons can then be used to search
for specific images and to view more detailed file information. (To return to the slide show
presentation, press the PLAY button)
3) Once a file has been highlight (indicated by the surrounding yellow window) individual files
can be deleted using the SETUP key. Once a file has been highlighted, use the PREVIOUS and
NEXT key and the PLAY button to confirm your choice. (To return to the slide show
presentation, press the PLAY button)
Advanced settings
From the THUMBNAIL screen, press the BACK key again to enter the MENU screen. The following
options are:
a. PHOTO: Highlight the PHOTO icon and press the PLAY key to enter this option. This screen is the
same as the previously noted THUMBNAIL screen (Use the BACK key to return back to the main
MENU screen)
AO-DPF7LB / AO-DPF8LB USER MANUAL
5
b. FILE: Highlight the FILE icon and press the PLAY key to enter this option. Like the previous
THUMBNAIL screen this view shows all files in a more condensed LIST style format. The above
mention technique for deleting files can also be applied. (Use the BACK key to return back to the
main MENU screen)
c. CALENDER: Highlight the CALENDER icon and press the PLAY key to enter this option. This screen
shows both a full month format calendar as well as the current time. Use the PREVIOUS and NEXT
key to move ahead or back days if required. A small version slide show is also visible in this screen
d. SETUP: Highlight the SETUP icon and press the PLAY key to enter this option. The setting
selections are as follows: Language > Photo Sequence > Slide Mode > Slide speed > Photo effect >
Slide effect > Photo mode > Display > Set date and time > Set time format > Format built-in
memory > Reset settings > Exit. Use PREVIOUS, NEXT and PLAY keys to select and confirm your
choice. Note: Once you have finished navigating these menu settings, you must return to the
THUMBNAIL or FILE LIST screen and press the play button to begin the slide show again.
e. ACCESSING EITHER USB OR SD CARD: From the slide show screen, press the BACK button 3
(three) times. Use the PREVIOUS and NEXT keys to then choose and confirm your selection.
(Note: Each memory type has it own user defined settings)
SPECIFICATIONS
Panel Size
7”
LED (AO
-
DPF7LB), 8" LED (AO
-
DPF8LB)
Resolution
800*600
Brightness
300 cd/m
Contrast
300:1
Viewing Angle
50/60/70/70(CR=10)
Response Time
30 ms
Screen Size Mode
16:9
File Format Type
JPEG
Po
wer Requirement
5V DC
Power Consumption
5W
Operation Temperature
-
20
℃
-
65
℃
Storage Temperature
-
30
℃
-
75
℃
Color
Black
Note: AO-DPF7LB / AO-DPF8LB will only display the photos in JPEG format,
For further product information and instruction please visit our product web page at
www.laserco.net or email support@laserco.com.au
Please note: As continual improvements are made to this product, slight operational
differences may occur. For the most up-to-date user manual, please visit our web site.
AO-DPF7LB / AO-DPF8LB USER MANUAL
6
Warranty Against Defects
Laser Corporation Pty Ltd (“Laser”) warrants your new product to be free from defects in
materials and workmanship for 12 months, from the date of purchase, provided that the
product is used in accordance with accompanying recommendations or instructions where
provided. The benefit of this warranty is in addition to your rights under the Australian
Consumer Law and to other rights and remedies of the consumer under a law in relation to
the goods or services to which the warranty relates.
Through a network of retailers and resellers, Laser will provide you with your choice of a
refund, repair or exchange (where possible) for this product if it becomes defective within the
warranty period. This warranty will no longer apply where the defect is a result of alteration,
accident, misuse, abuse, normal wear and tear, neglect or improper storage.
Please retain your receipt as proof of purchase
How to make a product warranty claim:
Step 1: Find your receipt which proves the date of purchase. Where the date of purchase
cannot be verified, your place of purchase or Laser will make an assessment based on the
date of manufacture, the condition of the Laser Product and the type of defect.
Step 2a): Contact your place of purchase. They will assess the nature of the fault and
refund or replace the product as per their store refund or warranty policy.
Step 2b): If your place of purchase cannot be contacted, then you can contact Laser .
Customer Service with details of your defective Laser Product: Phone: (02) 9870 3355; or
Email: service@laserco.com.au or online www.laserco.net/support/warranty (click on
“Consumers (End Users)”). Our business address is at 1/6-8 Byfield Street, North Ryde,
NSW 2113
Step 3: Laser . will issue you with a Return Authorisation (RA) number within 48 hours.
When requested, send us the defective Product and a copy of your receipt. Laser will cover
the cost of the return delivery.
Step 4: Wait for us to contact you. Once we have received your defective Laser Product for
inspection, we will inform you of our assessment of your claim within 7 days. When we
contact you, we will firstly let you know whether you have a valid claim under this Warranty,
and if so, we will inform you whether your defective Laser Product will be replaced or
repaired, together with the number of days you can expect to wait to receive your replaced
or repaired Laser Product.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Laser eBook-EB370 User manual
-
-
-
-
-
-
-
-
-
